mrjcd@daDeb:~$ ssh root@citadel-switch.mrjcd.com
DD-WRT v3.0-r47596 std (c) 2021 NewMedia-NET GmbH
Release: 10/25/21
Board: Netgear WNDR3700 V4
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
https://www.dd-wrt.com
==========================================================
BusyBox v1.34.1 (2021-10-25 07:42:47 +07) built-in shell (ash)
root@Citadel-Switch:~# dmesg
<6>[ 0.310000] Switched to clocksource MIPS
<6>[ 0.310000] NET: Registered protocol family 2
<6>[ 0.320000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.320000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.330000] TCP: Hash tables configured (established 1024 bind 1024)
<6>[ 0.330000] TCP: reno registered
<6>[ 0.340000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.340000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.350000] NET: Registered protocol family 1
<7>[ 0.350000] PCI: CLS 0 bytes, default 32
<5>[ 0.350000] gpio_proc: module loaded and /proc/gpio/ created (cool)
<6>[ 0.360000] fixup WNDR3700v4 wifi led
<5>[ 0.360000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<6>[ 0.370000] futex hash table entries: 256 (order: -1, 3072 bytes)
<6>[ 0.380000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>[ 0.390000] msgmni has been set to 245
<6>[ 0.390000] io scheduler noop registered
<6>[ 0.400000] io scheduler deadline registered (default)
<6>[ 0.400000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.410000] console [ttyS0] disabled
<6>[ 0.430000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
<6>[ 0.440000] console [ttyS0] enabled
<6>[ 0.450000] bootconsole [early0] disabled
<4>[ 0.460000] Atheros on-chip NAND FLash Controller Driver, Version 0.1 (c) 2010 Atheros Communications, Ltd.
<4>[ 0.470000] Ath Nand ID[87c721e0]: 2c:f1:80:95:02
<4>[ 0.470000] ONFI MICRON MT29F1G08ABADAWP
<4>[ 0.480000] Micron
<0>[ 1.490000]
<0>[ 1.490000] found squashfs at 0x7E0000
<5>[ 1.490000] Creating 7 MTD partitions on "ath-nand":
<5>[ 1.500000] 0x000000000000-0x000000080000 : "RedBoot"
<5>[ 1.510000] 0x0000006c0000-0x000008000000 : "linux"
<5>[ 3.560000] 0x0000007e0000-0x000001d00000 : "rootfs"
<5>[ 3.920000] mtd: partition "rootfs" set to be root filesystem
<5>[ 3.930000] 0x000001d00000-0x000008000000 : "ddwrt"
<5>[ 5.600000] 0x000000340000-0x0000003c0000 : "nvram"
<5>[ 5.620000] 0x000000080000-0x0000000c0000 : "board_config"
<5>[ 5.630000] 0x000000000000-0x000008000000 : "fullflash"
<4>[ 7.790000] ====== NAND Parameters ======
<4>[ 7.790000] sc = 0x87c72000 bbt = 0x87d00500 bbt_size = 0x100 nf_ctrl = 0x344
<4>[ 7.790000] page = 0x800 block = 0x20000 oob = 0x40
<4>[ 7.840000] registering PCI controller with io_map_base unset
<6>[ 7.850000] PCI host bridge to bus 0000:00
<6>[ 7.850000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
<6>[ 7.860000] pci_bus 0000:00: root bus resource [io 0x0000]
<6>[ 7.860000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
<7>[ 7.870000] pci 0000:00:00.0: [168c:0033] type 00 class 0x028000
<6>[ 7.870000] pci 0000:00:00.0: fixup device configuration
<0>[ 7.880000] bootstrap returns device 168C:33
<7>[ 7.880000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
<7>[ 7.880000] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
<7>[ 7.880000] pci 0000:00:00.0: supports D1
<7>[ 7.880000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
<7>[ 7.880000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
<6>[ 7.880000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
<6>[ 7.890000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
<6>[ 7.900000] pci 0000:00:00.0: using irq 72 for pin 1
<6>[ 7.900000] libphy: Fixed MDIO Bus: probed
<6>[ 7.910000] PPP generic driver version 2.4.2
<6>[ 7.910000] PPP BSD Compression module registered
<6>[ 7.920000] PPP Deflate Compression module registered
<6>[ 7.920000] PPP MPPE Compression module registered
<6>[ 7.930000] NET: Registered protocol family 24
<6>[ 7.940000] u32 classifier
<6>[ 7.940000] Performance counters on
<6>[ 7.940000] input device check on
<6>[ 7.950000] Actions configured
<6>[ 7.950000] Netfilter messages via NETLINK v0.30.
<6>[ 7.960000] nf_conntrack version 0.5.0 (1967 buckets, 7868 max)
<4>[ 7.960000] nf_conntrack_rtsp v0.7 loading
<4>[ 7.970000] nf_nat_rtsp v0.7 loading
<6>[ 7.970000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 7.980000] TCP: westwood registered
<6>[ 7.980000] TCP: hybla registered
<6>[ 7.980000] TCP: vegas registered
<6>[ 7.990000] NET: Registered protocol family 17
<6>[ 7.990000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
<5>[ 8.000000] Bridge firewalling registered
<6>[ 8.010000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 8.010000] searching for nvram
<6>[ 8.020000] nvram size = 524288
<6>[ 8.060000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 8.070000] ar71xx-wdt: timeout=15 secs (max=107) ref freq=40000000
<6>[ 8.110000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 8.110000] Freeing unused kernel memory: 136K
<6>[ 15.310000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
<6>[ 16.030000] libphy: ag71xx_mdio: probed
<6>[ 16.620000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
<6>[ 16.630000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
<6>[ 18.050000] Loading modules backported from Linux version v5.10-rc6-0-gb65054597872
<6>[ 18.050000] Backport generated by backports.git v5.10-rc6-1-0-g3a9d70a3
<6>[ 18.700000] eth0: link up (1000Mbps/Full duplex)
<7>[ 19.810000] ath: EEPROM regdomain sanitized
<7>[ 19.810000] ath: EEPROM regdomain: 0x64
<7>[ 19.810000] ath: EEPROM indicates we should expect a direct regpair map
<7>[ 19.810000] ath: Country alpha2 being used: 00
<7>[ 19.810000] ath: Regpair used: 0x64
<6>[ 19.820000] initialize fq_codel with 262144 bytes memory limit
<6>[ 19.830000] ieee80211_txq_setup_flows: set limit to 262144 bytes
<7>[ 19.840000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 19.840000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=78
<0>[ 19.850000] 2 vs 0
<4>[ 19.850000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
<7>[ 19.860000] ath: EEPROM regdomain sanitized
<7>[ 19.860000] ath: EEPROM regdomain: 0x64
<7>[ 19.860000] ath: EEPROM indicates we should expect a direct regpair map
<7>[ 19.860000] ath: Country alpha2 being used: 00
<7>[ 19.860000] ath: Regpair used: 0x64
<6>[ 19.870000] initialize fq_codel with 262144 bytes memory limit
<6>[ 19.880000] ieee80211_txq_setup_flows: set limit to 262144 bytes
<7>[ 19.890000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
<6>[ 19.890000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=72
<6>[ 20.750000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 4 is up
<6>[ 20.750000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 5 is up
<7>[ 20.780000] ar71xx-wdt: enabling watchdog timer
<6>[ 22.910000] device br0 entered promiscuous mode
<6>[ 23.020000] device vlan1 entered promiscuous mode
<6>[ 23.020000] device eth0 entered promiscuous mode
<6>[ 23.030000] br0: port 1(vlan1) entered forwarding state
<6>[ 23.030000] br0: port 1(vlan1) entered forwarding state
<6>[ 23.110000] device vlan2 entered promiscuous mode
<6>[ 23.120000] br0: port 2(vlan2) entered forwarding state
<6>[ 23.120000] br0: port 2(vlan2) entered forwarding state
<6>[ 23.150000] device br0 left promiscuous mode
<6>[ 23.160000] device br0 entered promiscuous mode
<6>[ 23.180000] device br0 left promiscuous mode
<7>[ 23.330000] ath: EEPROM regdomain: 0x8348
<7>[ 23.330000] ath: EEPROM indicates we should expect a country code
<7>[ 23.330000] ath: doing EEPROM country->regdmn map search
<7>[ 23.330000] ath: country maps to regdmn code: 0x3a
<7>[ 23.330000] ath: Country alpha2 being used: US
<7>[ 23.330000] ath: Regpair used: 0x3a
<7>[ 23.330000] ath: regdomain 0x8348 dynamically updated by user
<7>[ 23.330000] ath: EEPROM regdomain: 0x8348
<7>[ 23.330000] ath: EEPROM indicates we should expect a country code
<7>[ 23.330000] ath: doing EEPROM country->regdmn map search
<7>[ 23.330000] ath: country maps to regdmn code: 0x3a
<7>[ 23.330000] ath: Country alpha2 being used: US
<7>[ 23.330000] ath: Regpair used: 0x3a
<7>[ 23.330000] ath: regdomain 0x8348 dynamically updated by user
<6>[ 25.580000] device wlan1 entered promiscuous mode
<6>[ 26.630000] br0: port 3(wlan1) entered forwarding state
<6>[ 26.630000] br0: port 3(wlan1) entered forwarding state
<6>[ 26.830000] device wlan1.wds0 entered promiscuous mode
<6>[ 30.770000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 30.770000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>[ 35.930000] ip6_tables: (C) 2000-2006 Netfilter Core Team
<4>[ 36.500000] asn1_decoder: module license 'unspecified' taints kernel.
<4>[ 36.500000] Disabling lock debugging due to kernel taint
<6>[ 36.960000] Linux kernel CIFS/SMB SERVER 3.4.2 by Namjae Jeon <linkinjeon@kernel.org>
<6>[ 38.080000] br0: port 1(vlan1) entered forwarding state
<6>[ 38.160000] br0: port 2(vlan2) entered forwarding state
<6>[ 40.820000] usbcore: registered new interface driver usbfs
<6>[ 40.830000] usbcore: registered new interface driver hub
<6>[ 40.830000] usbcore: registered new device driver usb
<6>[ 41.070000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 41.120000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 41.120000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<4>[ 41.130000] ehci_reset Intialize USB CONTROLLER in host mode: 13
<4>[ 41.140000] ehci_reset Port Status 1c000000
<6>[ 41.170000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 41.190000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 41.190000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 41.200000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 41.210000] usb usb1: Product: Atheros AR91xx built-in EHCI controller
<6>[ 41.210000] usb usb1: Manufacturer: Linux 3.18.140-d6 ehci_hcd
<6>[ 41.220000] usb usb1: SerialNumber: platform
<6>[ 41.220000] hub 1-0:1.0: USB hub found
<6>[ 41.230000] hub 1-0:1.0: 1 port detected
<6>[ 41.580000] usb 1-1: new high-speed USB device number 2 using ar71xx-ehci
<6>[ 41.680000] br0: port 3(wlan1) entered forwarding state
<6>[ 41.730000] usb 1-1: New USB device found, idVendor=058f, idProduct=6387
<6>[ 41.740000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 41.750000] usb 1-1: Product: Mass Storage
<6>[ 41.750000] usb 1-1: Manufacturer: Generic
<6>[ 41.750000] usb 1-1: SerialNumber: F346A086
<5>[ 42.370000] SCSI subsystem initialized
<6>[ 42.710000] usb-storage 1-1:1.0: USB Mass Storage device detected
<6>[ 42.710000] scsi host0: usb-storage 1-1:1.0
<6>[ 42.720000] usbcore: registered new interface driver usb-storage
<5>[ 43.720000] scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 4
<5>[ 43.730000] sd 0:0:0:0: [sda] 31457280 512-byte logical blocks: (16.1 GB/15.0 GiB)
<5>[ 43.760000] sd 0:0:0:0: [sda] Write Protect is off
<7>[ 43.760000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
<5>[ 43.770000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
<6>[ 43.800000] sda: sda1
<5>[ 43.810000] sd 0:0:0:0: [sda] Attached SCSI removable disk
<6>[ 44.520000] ksmbd: kill command received
<5>[ 45.590000] random: nonblocking pool is initialized
<4>[ 49.280000] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
<4>[ 49.310000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
<6>[ 51.470000] Linux kernel CIFS/SMB SERVER 3.4.2 by Namjae Jeon <linkinjeon@kernel.org>
<6>[ 623.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 4 is down
<6>[ 627.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 4 is up
<6>[ 645.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 4 is down
<6>[ 691.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 4 is up
<6>[ 2473.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
<6>[ 2475.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is down
<6>[ 2477.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
<6>[ 2501.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is down
<6>[ 2503.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
<6>[ 2571.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is down
<6>[ 2575.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
<6>[ 2713.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is down
<6>[ 2723.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
<6>[ 2725.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is down
<6>[ 2729.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
<6>[ 5381.670000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is down
<6>[ 9991.150000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<3>[15980.750000] ksmbd: cannot get linux path (/mnt/sda1/MotoEdge+/~gvfSBam.tmp), err = -22
<3>[16028.520000] ksmbd: cannot get linux path (/mnt/sda1/MotoEdge+/Lotto_102721/TX_Lotto-103021.jpg), err = -22
root@Citadel-Switch:~# cat /tmp/smb.conf
[global]
log level = 1
netbios name = Citadel-Switch
server string =
syslog = 10
encrypt passwords = true
preferred master = yes
use sendfile = yes
aio read size = 2048
aio write size = 2048
large readwrite = yes
security = user
oplocks = yes
mangled names = no
max stat cache size = 64
workgroup =
bind interfaces only = yes
guest account = nobody
map to guest = bad user
smb passwd file = /var/samba/smbpasswd
private dir = /var/samba
passdb backend = smbpasswd
log file = /var/smbd.log
max log size = 1000
socket options = TCP_NODELAY IPTOS_LOWDELAY SO_SNDBUF=262144 SO_RCVBUF=262144
read raw = yes
write raw = yes
max xmit = 65536
dead time = 15
getwd cache = yes
lpq cache time = 30
server min protocol = SMB2_10
server max protocol = SMB3_11
printing = none
load printers = No
usershare allow guests = Yes
smb3 encryption = yes
[switch]
comment = switch
path = /mnt/sda1
read only = no
guest ok = no
valid users = mrjcd
force user = root
root@Citadel-Switch:~#
Connection to citadel-switch.mrjcd.com closed.
mrjcd@daDeb:~$