mrjcd@daDeb:~$ ssh root@wnr2000v3.mrjcd.com
DD-WRT v3.0-r54475 std (c) 2023 NewMedia-NET GmbH
Release: 12/07/23
Board: Netgear WNR2000v3
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
https://www.dd-wrt.com
==========================================================
BusyBox v1.36.1 (2023-12-07 07:39:36 +06) built-in shell (ash)
root@WNR2000v3:~# dmesg
root@WNR2000v3:~# cat /tmp/var/log/messages
Dec 31 18:00:02 WNR2000v3 syslog.info syslogd started: BusyBox v1.36.1
Dec 31 18:00:02 WNR2000v3 user.info : [klogd] : successfully started
Dec 31 18:00:02 WNR2000v3 kern.notice kernel: klogd started: BusyBox v1.36.1 (2023-12-07 07:39:36 +06)
Dec 31 18:00:02 WNR2000v3 kern.notice kernel: klogd: exiting
Dec 31 18:00:02 WNR2000v3 user.info : [resetbutton] : successfully started
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: start deconfigure_single_ath9k
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: start delete_ath9k_devices
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: leave delete_ath9k_devices
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: leave deconfigure_single_ath9k
Dec 31 18:00:02 WNR2000v3 user.info : [bridge] : bridge br0 successfully added
Dec 31 18:00:02 WNR2000v3 user.info : [bridge] : interface eth0 successfully added to bridge br0
Dec 31 18:00:02 WNR2000v3 user.info : [bridge] : interface eth1 successfully added to bridge br0
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: start deconfigure_single_ath9k
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: start delete_ath9k_devices
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: leave delete_ath9k_devices
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: leave deconfigure_single_ath9k
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: start configure_single_ath9k
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: start setRTS
Dec 31 18:00:02 WNR2000v3 user.debug : mac80211: leave setRTS
Dec 31 18:00:03 WNR2000v3 user.debug : mac80211: start setMacFilter
Dec 31 18:00:03 WNR2000v3 user.debug : mac80211: leave setMacFilter
Dec 31 18:00:04 WNR2000v3 user.info : [hostapd] : successfully started
Dec 31 18:00:04 WNR2000v3 user.info : [bridge] : interface wlan0 successfully added to bridge br0
Dec 31 18:00:04 WNR2000v3 user.info : [gratarp] : successfully started
Dec 31 18:00:05 WNR2000v3 syslog.info syslogd exiting
Dec 31 18:00:05 WNR2000v3 syslog.info syslogd started: BusyBox v1.36.1
Dec 31 18:00:05 WNR2000v3 user.info : [klogd] : successfully started
Dec 31 18:00:05 WNR2000v3 kern.notice kernel: klogd started: BusyBox v1.36.1 (2023-12-07 07:39:36 +06)
Dec 31 18:00:05 WNR2000v3 kern.notice kernel: klogd: exiting
Dec 31 18:00:05 WNR2000v3 user.info : [cron] : successfully started
Dec 31 18:00:05 WNR2000v3 cron.info cron[804]: (CRON) STARTUP (fork ok)
Dec 31 18:00:05 WNR2000v3 user.info : [wland] : successfully started
Dec 31 18:00:05 WNR2000v3 user.info : [dropbear] : successfully started
Dec 31 18:00:05 WNR2000v3 authpriv.info dropbear[816]: Running in background
Dec 31 18:00:07 WNR2000v3 daemon.info httpd[876]: [httpd] : httpd server started at port 80
Dec 31 18:00:07 WNR2000v3 user.info : [httpd] : successfully started
Dec 31 18:00:08 WNR2000v3 user.info : [wland] : daemon successfully stopped
Dec 31 18:00:08 WNR2000v3 user.info : [wland] : successfully started
Dec 31 18:00:09 WNR2000v3 user.info : [process_monitor] : successfully started
Dec 31 18:00:10 WNR2000v3 daemon.info httpd[888]: [httpd] : httpd server shutdown
Dec 31 18:00:10 WNR2000v3 user.info : [httpd] : daemon successfully stopped
Dec 31 18:00:10 WNR2000v3 daemon.info httpd[1212]: [httpd] : httpd server started at port 80
Dec 31 18:00:10 WNR2000v3 user.info : [httpd] : successfully started
Dec 31 18:00:10 WNR2000v3 user.info : [resetbutton] : daemon successfully stopped
Dec 31 18:00:10 WNR2000v3 user.info : [resetbutton] : successfully started
Dec 31 18:00:10 WNR2000v3 daemon.debug ntpclient[1209]: Connecting to 2.pool.ntp.org [12.167.151.1] ...
Dec 8 10:10:26 WNR2000v3 daemon.info ntpclient[1209]: Time set from 2.pool.ntp.org [12.167.151.1].
Dec 8 10:10:26 WNR2000v3 daemon.info process_monitor[1208]: Cyclic NTP Update success (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Dec 8 10:10:26 WNR2000v3 daemon.info process_monitor[1208]: Local timer delta is 0
Dec 8 10:10:26 WNR2000v3 daemon.debug process_monitor[1208]: Restarting cron (time sync change)
Dec 8 10:10:26 WNR2000v3 user.info : [cron] : daemon successfully stopped
Dec 8 10:10:27 WNR2000v3 user.info : [cron] : successfully started
Dec 8 10:10:27 WNR2000v3 cron.info cron[1259]: (CRON) STARTUP (fork ok)
Dec 8 10:10:27 WNR2000v3 daemon.debug process_monitor[1208]: We need to re-update after 3600 seconds
Dec 8 10:10:27 WNR2000v3 daemon.info process_monitor[1208]: [process_monitor] : set timer: 3600 seconds, callback: ntp_main()
Dec 8 10:10:27 WNR2000v3 daemon.info process_monitor[1208]: [process_monitor] : cleanup timers
Dec 8 10:10:27 WNR2000v3 user.info : [process_monitor] : daemon successfully stopped
Dec 8 10:10:27 WNR2000v3 user.info : [process_monitor] : successfully started
Dec 8 10:10:27 WNR2000v3 daemon.debug ntpclient[1286]: Connecting to 2.pool.ntp.org [12.167.151.1] ...
Dec 8 10:10:27 WNR2000v3 daemon.info ntpclient[1286]: Time set from 2.pool.ntp.org [12.167.151.1].
Dec 8 10:10:27 WNR2000v3 daemon.info process_monitor[1285]: Cyclic NTP Update success (servers 2.pool.ntp.org 212.18.3.19 88.99.174.22)
Dec 8 10:10:27 WNR2000v3 daemon.info process_monitor[1285]: Local timer delta is 0
Dec 8 10:10:27 WNR2000v3 daemon.debug process_monitor[1285]: We need to re-update after 3600 seconds
Dec 8 10:10:27 WNR2000v3 daemon.info process_monitor[1285]: [process_monitor] : set timer: 3600 seconds, callback: ntp_main()
Dec 8 10:13:18 WNR2000v3 authpriv.info dropbear[1720]: Child connection from 10.72.28.3:42406
Dec 8 10:13:18 WNR2000v3 authpriv.notice dropbear[1720]: Pubkey auth succeeded for 'root' with ssh-rsa key SHA256:8rGXH4R7z6eZ2tJK0tB/FEBhjCAhJiRe6qUpZPUDQ3U from 10.72.28.3:42406
root@WNR2000v3:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00050000 00010000 "RedBoot"
mtd1: 00390000 00010000 "linux"
mtd2: 00230000 00010000 "rootfs"
mtd3: 00060000 00010000 "ddwrt"
mtd4: 00010000 00010000 "nvram"
mtd5: 00010000 00010000 "board_config"
mtd6: 00400000 00010000 "fullflash"
mtd7: 00050000 00010000 "fullboot"
mtd8: 00010000 00010000 "uboot-env"
root@WNR2000v3:~# iw phy0 info
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 2 (up to 900m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Device supports T-DLS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CMAC (00-0f-ac:6)
* CMAC-256 (00-0f-ac:13)
* GMAC-128 (00-0f-ac:11)
* GMAC-256 (00-0f-ac:12)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* P2P-client
* P2P-GO
* outside context of a BSS
Band 1:
Capabilities: 0x11ee
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
Frequencies:
* 2412 MHz [1] (23.0 dBm)
* 2417 MHz [2] (23.0 dBm)
* 2422 MHz [3] (23.0 dBm)
* 2427 MHz [4] (23.0 dBm)
* 2432 MHz [5] (23.0 dBm)
* 2437 MHz [6] (23.0 dBm)
* 2442 MHz [7] (23.0 dBm)
* 2447 MHz [8] (23.0 dBm)
* 2452 MHz [9] (23.0 dBm)
* 2457 MHz [10] (23.0 dBm)
* 2462 MHz [11] (23.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2477 MHz [14] (23.0 dBm)
* 2482 MHz [15] (23.0 dBm)
* 2484 MHz [14] (20.0 dBm)
* 2487 MHz [14] (23.0 dBm)
* 2492 MHz [15] (23.0 dBm)
* 2497 MHz [16] (23.0 dBm)
* 2502 MHz [17] (23.0 dBm)
* 2507 MHz [18] (23.0 dBm)
* 2512 MHz [19] (23.0 dBm)
* 2517 MHz [20] (23.0 dBm)
* 2522 MHz [21] (23.0 dBm)
* 2527 MHz [22] (23.0 dBm)
* 2532 MHz [23] (23.0 dBm)
* 2537 MHz [24] (23.0 dBm)
* 2542 MHz [25] (23.0 dBm)
* 2547 MHz [26] (23.0 dBm)
* 2552 MHz [27] (23.0 dBm)
* 2557 MHz [28] (23.0 dBm)
* 2562 MHz [29] (23.0 dBm)
* 2567 MHz [30] (23.0 dBm)
* 2572 MHz [31] (23.0 dBm)
* 2577 MHz [32] (23.0 dBm)
* 2582 MHz [33] (23.0 dBm)
* 2587 MHz [34] (23.0 dBm)
* 2592 MHz [35] (23.0 dBm)
* 2597 MHz [36] (23.0 dBm)
* 2602 MHz [37] (23.0 dBm)
* 2607 MHz [38] (23.0 dBm)
* 2612 MHz [39] (23.0 dBm)
* 2617 MHz [40] (23.0 dBm)
* 2622 MHz [41] (23.0 dBm)
* 2627 MHz [42] (23.0 dBm)
* 2632 MHz [43] (23.0 dBm)
* 2637 MHz [44] (23.0 dBm)
* 2642 MHz [45] (23.0 dBm)
* 2647 MHz [46] (23.0 dBm)
* 2652 MHz [47] (23.0 dBm)
* 2657 MHz [48] (23.0 dBm)
* 2662 MHz [49] (23.0 dBm)
* 2667 MHz [50] (23.0 dBm)
* 2672 MHz [51] (23.0 dBm)
* 2677 MHz [52] (23.0 dBm)
* 2682 MHz [53] (23.0 dBm)
* 2687 MHz [54] (23.0 dBm)
* 2692 MHz [55] (23.0 dBm)
* 2697 MHz [56] (23.0 dBm)
* 2702 MHz [57] (23.0 dBm)
* 2707 MHz [58] (23.0 dBm)
* 2712 MHz [59] (23.0 dBm)
* 2717 MHz [60] (23.0 dBm)
* 2722 MHz [61] (23.0 dBm)
* 2727 MHz [62] (23.0 dBm)
* 2732 MHz [63] (23.0 dBm)
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 2048, #{ AP } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match
* #{ WDS } <= 2048,
total <= 2048, #channels <= 1, STA/AP BI must match
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
P2P GO supports CT window setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports active monitor (which will ACK incoming frames)
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device supports ACK timeout estimation.
Device supports configuring vdev MAC-addr on create.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ ACK_SIGNAL_SUPPORT ]: ack signal level support
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ MULTICAST_REGISTRATIONS ]: mgmt frame registration for multicast
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
root@WNR2000v3:~# iw wlan0 station dump
Station 9a:88:3b:85:ac:7f (on wlan0)
inactive time: 26460 ms
rx bytes: 693655
rx packets: 2464
tx bytes: 10771054
tx packets: 9246
tx retries: 126
tx failed: 0
rx drop misc: 2
signal: -49 [-52, -53] dBm
signal avg: -52 [-55, -54] dBm
tx bitrate: 130.0 MBit/s MCS 14 short GI
tx duration: 867105 us
rx bitrate: 6.0 MBit/s
rx duration: 169328 us
airtime weight: 256
expected throughput: 45.226Mbps
authorized: yes
authenticated: yes
associated: yes
preamble: short
WMM/WME: yes
MFP: no
TDLS peer: no
Powersave: yes
Compression: no
DTIM period: 2
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 368 seconds
associated at [boottime]: 32.048s
associated at: 1702051837698 ms
current time: 1702052206320 ms
Radio Name: root@WNR2000v3:~# uptime
10:17:28 up 7 min, load average: 0.00, 0.05, 0.04
root@WNR2000v3:~# date
Fri Dec 8 10:17:31 CST 2023
root@WNR2000v3:~#
Connection to wnr2000v3.mrjcd.com closed.
mrjcd@daDeb:~$ neofetch
_,met$$$$$gg. mrjcd@daDeb
,g$$$$$$$$$$$$$$$P. -----------
,g$$P" """Y$$.". OS: Debian GNU/Linux trixie/sid x86_64
,$$P' `$$$. Host: OptiPlex 7010 01
',$$P ,ggs. `$$b: Kernel: 6.5.0-5-amd64
`d$$' ,$P"' . $$$ Uptime: 2 days, 13 hours, 1 min
$$P d$' , $$P Packages: 2702 (dpkg)
$$: $$. - ,d$$' Shell: bash 5.2.21
$$; Y$b._ _,d$P' Resolution: 1600x900
Y$$. `.`"Y$$$$P"' DE: GNOME 44.5
`$$b "-.__ WM: Mutter
`Y$$ WM Theme: Adwaita
`Y$$. Theme: Adwaita [GTK2/3]
`$$b. Icons: gnome [GTK2/3]
`Y$$b. Terminal: gnome-terminal
`"Y$b._ CPU: Intel i5-3570 (4) @ 3.800GHz
`""" GPU: NVIDIA GeForce GT 1030
Memory: 1779MiB / 15945MiB
mrjcd@daDeb:~$