mrjcd@daDeb:~$ ssh root@citadel-station-homeworld.mrjcd.com
DD-WRT v3.0-r55846 std (c) 2024 NewMedia-NET GmbH
Release: 04/20/24
Board: Linksys EA8500
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
https://www.dd-wrt.com
==========================================================
BusyBox v1.36.1 (2024-04-20 02:22:03 +07) built-in shell (ash)
root@Citadel-Station-Homeworld:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 6.1.87 (root@server2) (arm-openwrt-linux-gcc (OpenWrt GCC 13.2.0 r24111-66f6c20e45) 13.2.0, GNU ld (GNU Binutils) 2.41) #131 SMP Sat Apr 20 02:18:06 +07 2024
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys EA8500 WiFi Router
[ 0.000000] OF: fdt: Ignoring memory range 0x41500000 - 0x42000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s17652 r8192 d23308 u49152
[ 0.000000] pcpu-alloc: s17652 r8192 d23308 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 471616K/491520K available (8181K kernel code, 807K rwdata, 2256K rodata, 1024K init, 2309K bss, 19904K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000003] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000026] Switching to timer-based delay loop, resolution 160ns
[ 0.000270] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000283] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000294] ... MAX_LOCK_DEPTH: 48
[ 0.000303] ... MAX_LOCKDEP_KEYS: 8192
[ 0.000311] ... CLASSHASH_SIZE: 4096
[ 0.000321] ... MAX_LOCKDEP_ENTRIES: 32768
[ 0.000329] ... MAX_LOCKDEP_CHAINS: 65536
[ 0.000339] ... CHAINHASH_SIZE: 32768
[ 0.000348] memory used by lock dependency info: 1861 kB
[ 0.000357] per task-struct memory footprint: 1536 bytes
[ 0.000425] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000456] CPU: Testing write buffer coherency: ok
[ 0.000539] pid_max: default: 32768 minimum: 301
[ 0.001340] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001366] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.004080] qcom_scm: convention: smc legacy
[ 0.005848] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.006180] rcu: Hierarchical SRCU implementation.
[ 0.006192] rcu: Max phase no-delay instances is 1000.
[ 0.007624] smp: Bringing up secondary CPUs ...
[ 0.011001] smp: Brought up 1 node, 2 CPUs
[ 0.011021] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.011038] CPU: All CPU(s) started in SVC mode.
[ 0.036668] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.037089] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.037126] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.037540] pinctrl core: initialized pinctrl subsystem
[ 0.041630] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.042383] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.045827] thermal_sys: Registered thermal governor 'step_wise'
[ 0.046141] cpuidle: using governor ladder
[ 0.046285] cpuidle: using governor menu
[ 0.109768] cryptd: max_cpu_qlen set to 1000
[ 0.114467] pps_core: LinuxPPS API ver. 1 registered
[ 0.114483] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.114541] PTP clock support registered
[ 0.117873] mctp: management component transport protocol core
[ 0.117891] NET: Registered PF_MCTP protocol family
[ 0.119087] clocksource: Switched to clocksource dg_timer
[ 0.120176] VFS: Disk quotas dquot_6.6.0
[ 0.120351] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.122584] NET: Registered PF_INET protocol family
[ 0.122927] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.125252] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 10240 bytes, linear)
[ 0.125337] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.125394] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.125523] TCP bind hash table entries: 4096 (order: 6, 327680 bytes, linear)
[ 0.127077] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.127874] MPTCP token hash table entries: 512 (order: 2, 24576 bytes, linear)
[ 0.128118] UDP hash table entries: 256 (order: 2, 24576 bytes, linear)
[ 0.128258] UDP-Lite hash table entries: 256 (order: 2, 24576 bytes, linear)
[ 0.128840] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.129027] PCI: CLS 0 bytes, default 64
[ 0.138656] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.154983] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.271333] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[ 0.271918] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[ 0.272182] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.272779] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.272839] qcom-pcie 1b500000.pci: Parsing ranges property...
[ 0.272910] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fe0ffff -> 0x0000000000
[ 0.273032] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[ 0.392054] qcom-pcie 1b500000.pci: Using 32 MSI vectors
[ 0.392449] qcom-pcie 1b500000.pci: iATU unroll: disabled
[ 0.392467] qcom-pcie 1b500000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[ 0.495288] qcom-pcie 1b500000.pci: PCIe Gen.1 x1 link up
[ 0.495708] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.495731] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.495753] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.495771] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.495791] pci_bus 0000:00: scanning bus
[ 0.495970] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.496225] pci 0000:00:00.0: supports D1
[ 0.496243] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.496317] pci 0000:00:00.0: PME# disabled
[ 0.500279] pci_bus 0000:00: fixups for bus
[ 0.500311] PCI: bus0: Fast back to back transfers disabled
[ 0.500332] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.500576] pci_bus 0000:01: scanning bus
[ 0.500857] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.501163] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.502574] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.502631] pci 0000:01:00.0: PME# disabled
[ 0.503053] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 0.504093] pci_bus 0000:01: fixups for bus
[ 0.504183] PCI: bus1: Fast back to back transfers disabled
[ 0.504200] pci_bus 0000:01: bus scan returning with max=01
[ 0.504223] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.504247] pci_bus 0000:00: bus scan returning with max=ff
[ 0.504287] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.504318] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.504470] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.504497] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.504925] pcieport 0000:00:00.0: assign IRQ: got 27
[ 0.505369] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x43c07000
[ 0.506400] pcieport 0000:00:00.0: AER: enabled with IRQ 28
[ 0.506605] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 0.506626] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 0.506642] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 0.506659] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 0.506675] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 0.506692] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 0.506708] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 0.506724] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 0.506740] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x8100800)
[ 0.506758] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 0.506774] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 0.506791] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 0.506807] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 0.506825] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 0.506842] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 0.506858] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3011b)
[ 0.508086] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[ 0.508533] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[ 0.508740] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.509301] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 0.509469] qcom-pcie 1b700000.pci: Parsing ranges property...
[ 0.509539] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031e0ffff -> 0x0000000000
[ 0.509597] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[ 0.632193] qcom-pcie 1b700000.pci: Using 32 MSI vectors
[ 0.632524] qcom-pcie 1b700000.pci: iATU unroll: disabled
[ 0.632545] qcom-pcie 1b700000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[ 0.735277] qcom-pcie 1b700000.pci: PCIe Gen.2 x1 link up
[ 0.735580] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.735603] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.735627] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
[ 0.735649] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.735669] pci_bus 0001:00: scanning bus
[ 0.735742] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.735931] pci 0001:00:00.0: supports D1
[ 0.735945] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.735967] pci 0001:00:00.0: PME# disabled
[ 0.739812] pci_bus 0001:00: fixups for bus
[ 0.739841] PCI: bus0: Fast back to back transfers disabled
[ 0.739862] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.740172] pci_bus 0001:01: scanning bus
[ 0.740512] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.740799] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.742113] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.742168] pci 0001:01:00.0: PME# disabled
[ 0.743521] pci_bus 0001:01: fixups for bus
[ 0.743605] PCI: bus1: Fast back to back transfers disabled
[ 0.743624] pci_bus 0001:01: bus scan returning with max=01
[ 0.743647] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.743672] pci_bus 0001:00: bus scan returning with max=ff
[ 0.743706] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.743735] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.743879] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.743907] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.744259] pcieport 0001:00:00.0: assign IRQ: got 30
[ 0.744492] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x43c5e000
[ 0.745298] pcieport 0001:00:00.0: AER: enabled with IRQ 31
[ 0.745547] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 0.745570] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 0.745586] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 0.745602] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 0.745619] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 0.745636] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 0.745652] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 0.745669] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 0.745686] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
[ 0.745703] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 0.745720] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 0.745736] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 0.745751] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 0.745768] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 0.745784] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 0.745800] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x3011e)
[ 0.852665] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[ 0.852690] krait-cc soc:clock-controller: CPU1 @ Undefined rate. Forcing new rate.
[ 0.852952] krait-cc soc:clock-controller: CPU1 @ 800000 KHz
[ 0.852972] krait-cc soc:clock-controller: L2 @ Undefined rate. Forcing new rate.
[ 0.853253] krait-cc soc:clock-controller: L2 @ 800000 KHz
[ 0.862087] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.865066] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.867036] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.867097] msm_serial 16340000.serial: uartclk = 7372800
[ 0.867293] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 35, base_baud = 460800) is a MSM
[ 0.867412] msm_serial: console setup on port #0
[ 1.809653] printk: console [ttyMSM0] enabled
[ 1.815145] msm_serial: driver initialized
[ 1.830202] loop: module loaded
[ 1.832770] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 1.832811] nand: AMD/Spansion S34MS01G2
[ 1.838757] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.299622] random: crng init done
[ 2.530385] found squashfs at 1380000 with len of 23855104 bytes
[ 3.217453] found squashfs at 3B80000 with len of 23068672 bytes
[ 3.217516] 19 fixed-partitions partitions found on MTD device qcom_nand.0
[ 3.222664] Creating 19 MTD partitions on "qcom_nand.0":
[ 3.229224] 0x000000000000-0x000000040000 : "SBL1"
[ 3.239318] 0x000000040000-0x000000180000 : "MIBIB"
[ 3.242660] 0x000000180000-0x0000002c0000 : "SBL2"
[ 3.247508] 0x0000002c0000-0x000000540000 : "SBL3"
[ 3.254895] 0x000000540000-0x000000660000 : "DDRCONFIG"
[ 3.258025] 0x000000660000-0x000000780000 : "SSD"
[ 3.262093] 0x000000780000-0x000000a00000 : "TZ"
[ 3.269633] 0x000000a00000-0x000000c80000 : "RPM"
[ 3.275383] 0x000000c80000-0x000000dc0000 : "art"
[ 3.278732] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[ 3.282009] 0x000000ec0000-0x000000f00000 : "u_env"
[ 3.285440] 0x000000f00000-0x000000f40000 : "s_env"
[ 3.290199] 0x000000f40000-0x000000f80000 : "devinfo"
[ 3.294972] 0x000000f80000-0x000003780000 : "linux"
[ 3.379146] 0x000001380000-0x000002a40000 : "rootfs"
[ 3.425130] mtd: setting mtd14 (rootfs) as root device
[ 3.425265] 0x000003780000-0x000005f40000 : "linux2"
[ 3.508880] 0x000003b80000-0x000005180000 : "rootfs2"
[ 3.553402] 0x000005f40000-0x000005f80000 : "nvram"
[ 3.554740] 0x000005f80000-0x000008000000 : "ddwrt"
[ 3.685041] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[ 4.486129] ar8327: qca,phy-rgmii-en is not specified
[ 4.487870] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[ 4.490276] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[ 4.497703] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 4.504908] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 4.510319] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 4.517689] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 4.523582] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 4.531291] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 4.539127] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 4.545005] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 4.552424] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 4.559096] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 4.566719] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 4.573747] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 4.579911] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address 22:7e:80:13:54:89
[ 4.592002] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[ 4.596253] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[ 4.603891] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 4.610728] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 4.616395] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 4.623936] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 4.629775] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 4.637395] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 4.645348] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 4.651190] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 4.658488] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 4.665342] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 4.672885] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 4.679900] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 4.686016] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address 5e:5d:48:c5:16:bb
[ 4.697755] PPP generic driver version 2.4.2
[ 4.702834] PPP BSD Compression module registered
[ 4.706841] PPP Deflate Compression module registered
[ 4.711957] PPP MPPE Compression module registered
[ 4.716479] NET: Registered PF_PPPOX protocol family
[ 4.721631] i2c_dev: i2c /dev entries driver
[ 4.734711] GACT probability NOT on
[ 4.734783] Mirror/redirect action on
[ 4.737120] Simple TC action Loaded
[ 4.742106] netem: version 1.3
[ 4.744206] u32 classifier
[ 4.747258] Performance counters on
[ 4.750040] input device check on
[ 4.753680] Actions configured
[ 4.759013] nf_conntrack_rtsp v0.7 loading
[ 4.762231] xt_time: kernel timezone is -0000
[ 4.765315] gre: GRE over IPv4 demultiplexor driver
[ 4.770656] NET: Registered PF_INET6 protocol family
[ 4.776862] Segment Routing with IPv6
[ 4.779239] In-situ OAM (IOAM) with IPv6
[ 4.783086] NET: Registered PF_PACKET protocol family
[ 4.787085] Bridge firewalling registered
[ 4.791776] 8021q: 802.1Q VLAN Support v1.8
[ 4.795922] Registering SWP/SWPB emulation handler
[ 4.804051] registered taskstats version 1
[ 4.873118] Failed to get APPS FABRIC clock
[ 4.876644] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 4.903548] s1a: Bringing 0uV into 1050000-1050000uV
[ 4.904390] s1b: Bringing 0uV into 1050000-1050000uV
[ 4.908229] s2a: Bringing 0uV into 800000-800000uV
[ 4.913335] s2b: Bringing 0uV into 800000-800000uV
[ 4.929444] thermal thermal_zone0: failed to read out thermal zone (-110)
[ 4.955048] searching for nvram
[ 4.955106] nvram size = 262144
[ 5.018765] found nvram at 20000
[ 5.051246] UBI error: no valid UBI magic found inside mtd13
[ 5.064155] VFS: Mounted root (squashfs filesystem) readonly on device 31:14.
[ 5.064861] Freeing unused kernel image (initmem) memory: 1024K
[ 5.070634] Run /sbin/init as init process
[ 5.075996] with arguments:
[ 5.076002] /sbin/init
[ 5.076008] with environment:
[ 5.076014] HOME=/
[ 5.076019] TERM=linux
[ 10.341370] ath9k: ath9k: Driver unloaded
[ 10.764193] ath10k_pci 0000:01:00.0: assign IRQ: got 27
[ 10.765977] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 10.766083] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 10.767028] qcom-pcie 1b500000.pci: msi#1 address_hi 0x0 address_lo 0x43c07000
[ 10.767216] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.102235] ath10k_pci 0000:01:00.0: found firmware features ie (8 B)
[ 11.102283] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 11.107668] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0
[ 11.118947] ath10k_pci 0000:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7768 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 57333134
[ 11.183257] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[ 11.186562] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 11.192571] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 11.215565] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 e4a0f655
[ 11.236868] ath10k_pci 0000:01:00.0: boot already acquired valid otp board id,skip download, board_id 2 chip_id 1
[ 11.257403] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11240
[ 12.188600] ath10k_pci 0000:01:00.0: Init Max Stations to 64
[ 12.189373] ath10k_pci 0000:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000002 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2500 low_5ghz_chan 4800 high_5ghz_chan 6115 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 12.280602] ath10k_pci 0000:01:00.0: ChipType 1200 ChipTypeID 30 BoardID 1 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0
[ 12.281491] ath10k_pci 0000:01:00.0: free: 23232 iram: 29408 sram: 19112
[ 12.291998] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr 14:91:82:7d:ef:7d status 0
[ 12.330026] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 12.413827] ath10k_pci 0000:01:00.0: init channel number 86
[ 12.420193] ath10k_pci 0001:01:00.0: assign IRQ: got 30
[ 12.421042] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 12.421149] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 12.421777] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x43c5e000
[ 12.421954] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 12.581442] ath10k_pci 0001:01:00.0: found firmware features ie (8 B)
[ 12.581487] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 12.586870] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0
[ 12.598324] ath10k_pci 0001:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7768 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 57333134
[ 12.662197] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[ 12.665501] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 12.671505] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 12.681069] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 e4a0f655
[ 12.710296] ath10k_pci 0001:01:00.0: boot already acquired valid otp board id,skip download, board_id 1 chip_id 1
[ 12.730718] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11240
[ 13.658508] ath10k_pci 0001:01:00.0: Init Max Stations to 64
[ 13.659312] ath10k_pci 0001:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000001 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2500 low_5ghz_chan 4800 high_5ghz_chan 6115 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 13.747944] ath10k_pci 0001:01:00.0: ChipType 1200 ChipTypeID 30 BoardID 2 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0
[ 13.748800] ath10k_pci 0001:01:00.0: free: 23232 iram: 29408 sram: 19112
[ 13.759339] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr 14:91:82:7d:ef:7d status 0
[ 13.796631] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 13.884209] ath10k_pci 0001:01:00.0: init channel number 281
[ 15.056344] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.067131] dwmac1000: Master AXI performs any burst length
[ 15.067163] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 15.081590] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 15.081896] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 15.090400] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 15.097102] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.105183] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.117355] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.130673] dwmac1000: Master AXI performs any burst length
[ 15.130704] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 15.145062] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 15.145268] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 15.153792] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 15.160222] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.168466] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 17.787799] device br0 entered promiscuous mode
[ 17.851579] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 17.869340] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 17.880390] dwmac1000: Master AXI performs any burst length
[ 17.880423] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 17.894778] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 17.894982] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 17.902702] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 17.909932] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 17.918181] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 17.935340] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 17.947238] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 17.958008] dwmac1000: Master AXI performs any burst length
[ 17.958041] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 17.972477] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 17.972679] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 17.980394] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 17.987361] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 17.995979] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 18.007285] br0: port 1(eth1) entered blocking state
[ 18.016021] br0: port 1(eth1) entered disabled state
[ 18.021522] device eth1 entered promiscuous mode
[ 18.026220] br0: port 1(eth1) entered blocking state
[ 18.030754] br0: port 1(eth1) entered forwarding state
[ 18.035723] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[ 18.057509] device br0 left promiscuous mode
[ 18.061986] device br0 entered promiscuous mode
[ 18.144916] device br0 left promiscuous mode
[ 18.299183] ath10k_pci 0001:01:00.0: Core CLK 300
[ 18.299222] ath10k_pci 0001:01:00.0: Mac CLK 150
[ 19.269228] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[ 19.292924] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11240
[ 20.222002] ath10k_pci 0001:01:00.0: Init Max Stations to 64
[ 20.222042] ath10k_pci 0001:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000001 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2500 low_5ghz_chan 4800 high_5ghz_chan 6115 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 20.311379] ath10k_pci 0001:01:00.0: ChipType 1200 ChipTypeID 30 BoardID 2 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0
[ 20.312253] ath10k_pci 0001:01:00.0: free: 23232 iram: 29408 sram: 19112
[ 20.322774] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr 14:91:82:7d:ef:7d status 0
[ 20.417608] ath10k_pci 0001:01:00.0: Init Channel Number 40
[ 20.446808] ath10k_pci 0001:01:00.0: set base mac addr 14:91:82:7d:ef:80
[ 20.480606] br0: port 2(wlan1) entered blocking state
[ 20.480642] br0: port 2(wlan1) entered disabled state
[ 20.485010] device wlan1 entered promiscuous mode
[ 20.489834] br0: port 2(wlan1) entered blocking state
[ 20.494363] br0: port 2(wlan1) entered forwarding state
[ 20.500004] br0: port 2(wlan1) entered disabled state
[ 20.628278] ath10k_pci 0001:01:00.0: mac txpower 30
[ 20.941663] ath10k_pci 0001:01:00.0: mac txpower 30
[ 20.942065] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 20.945518] br0: port 2(wlan1) entered blocking state
[ 20.952037] br0: port 2(wlan1) entered forwarding state
[ 21.131462] ath10k_pci 0000:01:00.0: user requested fw restart
[ 21.421541] ath10k_pci 0000:01:00.0: found firmware features ie (4 B)
[ 21.421590] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 21.426973] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0
[ 21.438376] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.18-00002 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 4716237b
[ 21.502488] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[ 21.505789] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 21.511918] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 21.521411] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 e4a0f655
[ 21.550777] ath10k_pci 0000:01:00.0: boot already acquired valid otp board id,skip download, board_id 2 chip_id 1
[ 21.571333] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11240
[ 22.724923] ath10k_pci 0000:01:00.0: Init Max Stations to 512
[ 22.726585] ath10k_pci 0000:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000002 fw_build 0x00000000 phy_capab 0x00000002 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000008 min_pkt_size_enable 0x00000000
[ 22.817840] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr 14:91:82:7d:ef:7d status 0
[ 22.848583] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 22.934112] ath10k_pci 0000:01:00.0: init channel number 14
[ 22.959489] ath10k_pci 0000:01:00.0: Core CLK 300
[ 22.959528] ath10k_pci 0000:01:00.0: Mac CLK 150
[ 23.318760] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[ 23.342629] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11240
[ 24.496698] ath10k_pci 0000:01:00.0: Init Max Stations to 512
[ 24.496739] ath10k_pci 0000:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000002 fw_build 0x00000000 phy_capab 0x00000002 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000008 min_pkt_size_enable 0x00000000
[ 24.590334] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr 14:91:82:7d:ef:7d status 0
[ 24.681692] ath10k_pci 0000:01:00.0: Init Channel Number 14
[ 24.711459] ath10k_pci 0000:01:00.0: set base mac addr 14:91:82:7d:ef:7f
[ 24.711621] ath10k_pci 0000:01:00.0: bdf failsafe status event received from fw: 0
[ 24.747438] br0: port 3(wlan0) entered blocking state
[ 24.747477] br0: port 3(wlan0) entered disabled state
[ 24.751941] device wlan0 entered promiscuous mode
[ 24.781958] ath10k_pci 0000:01:00.0: mac txpower 30
[ 25.118402] ath10k_pci 0000:01:00.0: mac txpower 30
[ 25.119704] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 25.122261] br0: port 3(wlan0) entered blocking state
[ 25.128687] br0: port 3(wlan0) entered forwarding state
[ 25.259605] ath10k_pci 0001:01:00.0: Init Channel Number 91
[ 25.259988] ath10k_pci 0000:01:00.0: Init Channel Number 14
[ 25.565330] ath10k_pci 0000:01:00.0: bdf failsafe status event received from fw: 0
[ 25.567722] ath10k_pci 0001:01:00.0: Init Channel Number 173
[ 25.573037] ath10k_pci 0000:01:00.0: Init Channel Number 11
[ 25.578823] ath10k_pci 0000:01:00.0: bdf failsafe status event received from fw: 0
[ 25.584463] ath10k_pci 0000:01:00.0: Init Channel Number 11
[ 25.594496] ath10k_pci 0000:01:00.0: bdf failsafe status event received from fw: 0
[ 25.597470] ath10k_pci 0001:01:00.0: Init Channel Number 40
[ 25.662818] device wlan0 left promiscuous mode
[ 25.662960] br0: port 3(wlan0) entered disabled state
[ 25.816466] device wlan1 left promiscuous mode
[ 25.816606] br0: port 2(wlan1) entered disabled state
[ 26.758485] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[ 26.782198] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11240
[ 27.709911] ath10k_pci 0001:01:00.0: Init Max Stations to 64
[ 27.709954] ath10k_pci 0001:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000001 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2500 low_5ghz_chan 4800 high_5ghz_chan 6115 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 27.799760] ath10k_pci 0001:01:00.0: ChipType 1200 ChipTypeID 30 BoardID 2 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0
[ 27.800544] ath10k_pci 0001:01:00.0: free: 23232 iram: 29408 sram: 19112
[ 27.811160] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr 14:91:82:7d:ef:7d status 0
[ 27.906295] ath10k_pci 0001:01:00.0: Init Channel Number 40
[ 27.935562] ath10k_pci 0001:01:00.0: set base mac addr 14:91:82:7d:ef:80
[ 27.970425] br0: port 2(wlan1) entered blocking state
[ 27.970461] br0: port 2(wlan1) entered disabled state
[ 27.974792] device wlan1 entered promiscuous mode
[ 28.003178] ath10k_pci 0001:01:00.0: mac txpower 30
[ 28.316253] ath10k_pci 0001:01:00.0: mac txpower 30
[ 28.317618] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 28.320191] br0: port 2(wlan1) entered blocking state
[ 28.326537] br0: port 2(wlan1) entered forwarding state
[ 28.849303] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[ 28.873210] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11240
[ 30.026491] ath10k_pci 0000:01:00.0: Init Max Stations to 512
[ 30.026531] ath10k_pci 0000:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000002 fw_build 0x00000000 phy_capab 0x00000002 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000008 min_pkt_size_enable 0x00000000
[ 30.120454] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr 14:91:82:7d:ef:7d status 0
[ 30.211426] ath10k_pci 0000:01:00.0: Init Channel Number 11
[ 30.241016] ath10k_pci 0000:01:00.0: set base mac addr 14:91:82:7d:ef:7f
[ 30.241272] ath10k_pci 0000:01:00.0: bdf failsafe status event received from fw: 0
[ 30.280703] br0: port 3(wlan0) entered blocking state
[ 30.280741] br0: port 3(wlan0) entered disabled state
[ 30.285072] device wlan0 entered promiscuous mode
[ 30.289970] br0: port 3(wlan0) entered blocking state
[ 30.294474] br0: port 3(wlan0) entered forwarding state
[ 30.305487] br0: port 3(wlan0) entered disabled state
[ 30.332060] ath10k_pci 0000:01:00.0: mac txpower 30
[ 30.668714] ath10k_pci 0000:01:00.0: mac txpower 30
[ 30.669543] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 30.672558] br0: port 3(wlan0) entered blocking state
[ 30.678999] br0: port 3(wlan0) entered forwarding state
[ 30.813595] ath10k_pci 0001:01:00.0: Init Channel Number 91
[ 30.814000] ath10k_pci 0000:01:00.0: Init Channel Number 14
[ 31.119308] ath10k_pci 0001:01:00.0: Init Channel Number 173
[ 31.120286] ath10k_pci 0000:01:00.0: Init Channel Number 11
[ 31.124303] ath10k_pci 0000:01:00.0: bdf failsafe status event received from fw: 0
[ 31.131752] ath10k_pci 0000:01:00.0: bdf failsafe status event received from fw: 0
[ 31.138144] ath10k_pci 0000:01:00.0: Init Channel Number 11
[ 31.147685] ath10k_pci 0000:01:00.0: bdf failsafe status event received from fw: 0
[ 31.154486] ath10k_pci 0001:01:00.0: Init Channel Number 40
[ 31.661210] device eth0 entered promiscuous mode
[ 34.158699] ksmbd: unknown parameter 'connlimit' ignored
[ 35.362622] INFO: trying to register non-static key.
[ 35.362652] The code is fine but needs lockdep annotation, or maybe
[ 35.366652] you didn't initialize this object before use?
[ 35.372641] turning off the locking correctness validator.
[ 35.378198] CPU: 1 PID: 2174 Comm: tc Not tainted 6.1.87 #131
[ 35.383577] Hardware name: Generic DT based system
[ 35.389395] Backtrace:
[ 35.394078] [<c030e018>] (dump_backtrace) from [<c030e3a4>] (show_stack+0x18/0x1c)
[ 35.396433] r7:c11c3d30 r6:00000000 r5:20000093 r4:c0c3c860
[ 35.404063] [<c030e38c>] (show_stack) from [<c0ac7e14>] (dump_stack_lvl+0x48/0x54)
[ 35.409883] [<c0ac7dcc>] (dump_stack_lvl) from [<c0ac7e38>] (dump_stack+0x18/0x1c)
[ 35.417263] r5:00000000 r4:00000000
[ 35.424808] [<c0ac7e20>] (dump_stack) from [<c038cf7c>] (register_lock_class+0x804/0x818)
[ 35.428549] [<c038c778>] (register_lock_class) from [<c038bea8>] (__lock_acquire.isra.0+0x4c/0x4e0)
[ 35.436623] r10:00000002 r9:c44e7c24 r8:00000080 r7:60000093 r6:00000000 r5:00000000
[ 35.445476] r4:c1d60f00
[ 35.453452] [<c038be5c>] (__lock_acquire.isra.0) from [<c038c3cc>] (lock_acquire+0x90/0xdc)
[ 35.456068] r10:00000000 r9:c080fc04 r8:00000080 r7:60000093 r6:00000000 r5:c5297a68
[ 35.464137] r4:c0e453d0
[ 35.472115] [<c038c33c>] (lock_acquire) from [<c080fba4>] (___gnet_stats_copy_basic+0x2a0/0x2e0)
[ 35.474732] r8:c44e7c10 r7:c44e7c24 r6:00000001 r5:20000013 r4:c5297b88
[ 35.483494] [<c080f904>] (___gnet_stats_copy_basic) from [<c080fc04>] (gnet_stats_copy_basic+0x20/0x28)
[ 35.490184] r10:c3876010 r9:c5297b88 r8:c0cdcb1c r7:00000000 r6:c5297b88 r5:00000000
[ 35.499293] r4:c44e7c00
[ 35.507271] [<c080fbe4>] (gnet_stats_copy_basic) from [<c08832d8>] (hfsc_dump_class_stats+0x8c/0xe4)
[ 35.509886] [<c088324c>] (hfsc_dump_class_stats) from [<c0865a1c>] (tc_fill_tclass+0x150/0x1f8)
[ 35.519001] r7:c3876000 r6:c39eb800 r5:c3876000 r4:c48ff600
[ 35.527416] [<c08658cc>] (tc_fill_tclass) from [<c0866668>] (tc_ctl_tclass+0x1e8/0x51c)
[ 35.533324] r10:00010000 r9:0000087e r8:c39eb800 r7:00010001 r6:c5297d18 r5:00000000
[ 35.541046] r4:c5025400
[ 35.549025] [<c0866480>] (tc_ctl_tclass) from [<c0839428>] (rtnetlink_rcv_msg+0x13c/0x374)
[ 35.551643] r10:00000000 r9:00000000 r8:c11f9d9c r7:c48ff540 r6:00000000 r5:00000018
[ 35.559710] r4:c5025400
[ 35.567600] [<c08392ec>] (rtnetlink_rcv_msg) from [<c08b005c>] (netlink_rcv_skb+0x40/0x110)
[ 35.570216] r10:c5025500 r9:c39ef244 r8:c08392ec r7:c48ff540 r6:c5025400 r5:00000000
[ 35.578286] r4:00000000
[ 35.586266] [<c08b001c>] (netlink_rcv_skb) from [<c0838204>] (rtnetlink_rcv+0x18/0x20)
[ 35.588880] r8:00000054 r7:c1419000 r6:00000000 r5:c39ef000 r4:c48ff540
[ 35.596600] [<c08381ec>] (rtnetlink_rcv) from [<c08af738>] (netlink_unicast+0x234/0x310)
[ 35.603460] [<c08af504>] (netlink_unicast) from [<c08af9ec>] (netlink_sendmsg+0x1d8/0x410)
[ 35.611536] r10:00000000 r9:c5297f50 r8:c39ef000 r7:c48ff540 r6:00000054 r5:c5297f40
[ 35.619605] r4:00000054
[ 35.627497] [<c08af814>] (netlink_sendmsg) from [<c07f39d8>] (___sys_sendmsg+0x310/0x334)
[ 35.630113] r10:00000054 r9:c5297e28 r8:c5297e28 r7:00000000 r6:c2582300 r5:c08af814
[ 35.638183] r4:c5297f40
[ 35.645988] [<c07f36c8>] (___sys_sendmsg) from [<c07f55e0>] (sys_sendmsg+0x88/0xb4)
[ 35.648601] r10:00000128 r9:c1d60f00 r8:c0300268 r7:c2582300 r6:00000000 r5:bec1ccb4
[ 35.655977] r4:00000000
[ 35.663956] [<c07f5558>] (sys_sendmsg) from [<c0300060>] (ret_fast_syscall+0x0/0x54)
[ 35.666567] Exception stack(0xc5297fa8 to 0xc5297ff0)
[ 35.674292] 7fa0: 00000000 00000000 00000003 bec1ccb4 00000000 00000000
[ 35.679244] 7fc0: 00000000 00000000 bec1ccb8 00000128 0002be58 00000025 00000000 00000000
[ 35.687404] 7fe0: bec1cc60 bec1cc50 b6f73730 b6f72c00
[ 35.695559] r7:00000128 r6:bec1ccb8 r5:00000000 r4:00000000
[ 37.235711] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[ 37.243866] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 37.254608] dwmac1000: Master AXI performs any burst length
[ 37.254638] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 37.269019] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 37.269161] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 37.276950] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 37.283883] device eth0 left promiscuous mode
[ 37.292678] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 37.296708] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 37.650798] usbcore: registered new interface driver usbfs
[ 37.650874] usbcore: registered new interface driver hub
[ 37.655596] usbcore: registered new device driver usb
[ 38.528369] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 38.528433] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 38.533040] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 38.540446] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x11000000
[ 38.549996] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 38.555656] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 38.561252] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 38.570313] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 38.575324] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 38.583683] usb usb1: Product: xHCI Host Controller
[ 38.590800] usb usb1: Manufacturer: Linux 6.1.87 xhci-hcd
[ 38.595516] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 38.603413] hub 1-0:1.0: USB hub found
[ 38.606297] hub 1-0:1.0: 1 port detected
[ 38.610272] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 38.614195] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 38.621838] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 38.629886] usb usb2: Product: xHCI Host Controller
[ 38.637011] usb usb2: Manufacturer: Linux 6.1.87 xhci-hcd
[ 38.641912] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 38.648712] hub 2-0:1.0: USB hub found
[ 38.652318] hub 2-0:1.0: 1 port detected
[ 38.718253] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 38.718303] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 38.722952] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 38.730300] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x10000000
[ 38.739854] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 38.745472] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 38.751115] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 38.759548] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 38.765189] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 38.773693] usb usb3: Product: xHCI Host Controller
[ 38.780718] usb usb3: Manufacturer: Linux 6.1.87 xhci-hcd
[ 38.785402] usb usb3: SerialNumber: xhci-hcd.1.auto
[ 38.791611] hub 3-0:1.0: USB hub found
[ 38.795697] hub 3-0:1.0: 1 port detected
[ 38.800028] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 38.804527] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 38.811846] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 38.819802] usb usb4: Product: xHCI Host Controller
[ 38.826902] usb usb4: Manufacturer: Linux 6.1.87 xhci-hcd
[ 38.831726] usb usb4: SerialNumber: xhci-hcd.1.auto
[ 38.837763] hub 4-0:1.0: USB hub found
[ 38.842056] hub 4-0:1.0: 1 port detected
[ 39.201190] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 40.169844] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 40.200658] usb 2-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 40.200700] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 40.207919] usb 2-1: Product: Flash Drive
[ 40.215040] usb 2-1: Manufacturer: Samsung
[ 40.215048] usb 2-1: SerialNumber: 0373819090017746
[ 43.983632] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 43.983672] usb usb4: USB disconnect, device number 1
[ 43.988254] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 43.992805] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 43.998440] usb usb3: USB disconnect, device number 1
[ 44.004772] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 44.008514] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 44.014276] usb usb2: USB disconnect, device number 1
[ 44.019095] usb 2-1: USB disconnect, device number 2
[ 44.025528] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 44.029180] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 44.034909] usb usb1: USB disconnect, device number 1
[ 44.040783] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 44.112824] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 44.112877] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 44.117413] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 44.124865] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x11000000
[ 44.134441] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 44.140121] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 44.145598] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 44.153423] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 44.159803] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 44.167987] usb usb1: Product: xHCI Host Controller
[ 44.175271] usb usb1: Manufacturer: Linux 6.1.87 xhci-hcd
[ 44.180036] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 44.186006] hub 1-0:1.0: USB hub found
[ 44.190345] hub 1-0:1.0: 1 port detected
[ 44.194502] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 44.198301] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 44.206251] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 44.214343] usb usb2: Product: xHCI Host Controller
[ 44.221535] usb usb2: Manufacturer: Linux 6.1.87 xhci-hcd
[ 44.226232] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 44.232323] hub 2-0:1.0: USB hub found
[ 44.236551] hub 2-0:1.0: 1 port detected
[ 44.240907] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 44.244412] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 44.249981] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 44.257258] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x10000000
[ 44.266887] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 44.272579] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 44.278064] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 44.285918] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 44.292292] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 44.300533] usb usb3: Product: xHCI Host Controller
[ 44.307655] usb usb3: Manufacturer: Linux 6.1.87 xhci-hcd
[ 44.312491] usb usb3: SerialNumber: xhci-hcd.1.auto
[ 44.318404] hub 3-0:1.0: USB hub found
[ 44.322804] hub 3-0:1.0: 1 port detected
[ 44.326962] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 44.330840] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 44.338652] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 44.346804] usb usb4: Product: xHCI Host Controller
[ 44.353990] usb usb4: Manufacturer: Linux 6.1.87 xhci-hcd
[ 44.358696] usb usb4: SerialNumber: xhci-hcd.1.auto
[ 44.364909] hub 4-0:1.0: USB hub found
[ 44.369013] hub 4-0:1.0: 1 port detected
[ 44.640373] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 44.670870] usb 2-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 44.670910] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 44.678041] usb 2-1: Product: Flash Drive
[ 44.678050] usb 2-1: Manufacturer: Samsung
[ 44.678056] usb 2-1: SerialNumber: 0373819090017746
[ 45.098558] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 45.113505] usbcore: registered new interface driver usb-storage
[ 45.172657] usbcore: registered new interface driver uas
[ 45.432525] ahci 29000000.sata: supply ahci not found, using dummy regulator
[ 45.432728] ahci 29000000.sata: supply phy not found, using dummy regulator
[ 45.438800] ahci 29000000.sata: supply target not found, using dummy regulator
[ 46.396780] sda: sda1
[ 48.999188] ksmbd: unknown parameter 'connlimit' ignored
root@Citadel-Station-Homeworld:~# uptime && date
14:52:15 up 4 min, load average: 0.12, 0.23, 0.11
Sat Apr 20 14:52:15 CDT 2024
root@Citadel-Station-Homeworld:~#
Connection to citadel-station-homeworld.mrjcd.com closed.
mrjcd@daDeb:~$