mrjcd@daDeb:~$ ssh root@ea8500.mrjcd.com
DD-WRT v3.0-r55776 std (c) 2024 NewMedia-NET GmbH
Release: 04/11/24
Board: Linksys EA8500
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
https://www.dd-wrt.com
==========================================================
BusyBox v1.36.1 (2024-04-11 13:15:19 +07) built-in shell (ash)
root@EA8500:~# ifconfig
br0 Link encap:Ethernet HWaddr C0:56:27:08:B2:92
inet addr:10.72.28.52 Bcast:10.72.28.255 Mask:255.255.255.0
inet6 addr: fe80::c256:27ff:fe08:b292/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:39196 errors:0 dropped:0 overruns:0 frame:0
TX packets:37350 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:26848202 (25.6 MiB) TX bytes:28417491 (27.1 MiB)
br1 Link encap:Ethernet HWaddr C0:56:27:08:B2:92
inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::865:3dff:fe3a:b331/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:880 (880.0 B)
eth0 Link encap:Ethernet HWaddr C0:56:27:08:B2:92
inet6 addr: fe80::c256:27ff:fe08:b292/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1790 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:417247 (407.4 KiB)
Interrupt:36
eth1 Link encap:Ethernet HWaddr C0:56:27:08:B2:92
inet6 addr: fe80::c256:27ff:fe08:b292/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:39213 errors:0 dropped:0 overruns:0 frame:0
TX packets:38940 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:27398681 (26.1 MiB) TX bytes:28511611 (27.1 MiB)
Interrupt:37
eth1.15 Link encap:Ethernet HWaddr C0:56:27:08:B2:92
inet6 addr: fe80::c256:27ff:fe08:b292/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1168 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:61348 (59.9 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MULTICAST MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
tun2 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:10.19.92.225 P-t-P:10.19.92.225 Mask:255.255.255.224
inet6 addr: fe80::6e3d:d03b:cad0:f1b1/64 Scope:Link
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1392 Metric:1
RX packets:15614 errors:0 dropped:0 overruns:0 frame:0
TX packets:20653 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1316994 (1.2 MiB) TX bytes:25882022 (24.6 MiB)
root@EA8500:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 6.1.84 (root@server2) (arm-openwrt-linux-gcc (OpenWrt GCC 13.2.0 r24111-66f6c20e45) 13.2.0, GNU ld (GNU Binutils) 2.41) #128 SMP Wed Apr 10 12:57:44 +07 2024
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys EA8500 WiFi Router
[ 0.000000] OF: fdt: Ignoring memory range 0x41500000 - 0x42000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s17652 r8192 d23308 u49152
[ 0.000000] pcpu-alloc: s17652 r8192 d23308 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 471616K/491520K available (8180K kernel code, 807K rwdata, 2256K rodata, 1024K init, 2309K bss, 19904K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000001] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000024] Switching to timer-based delay loop, resolution 160ns
[ 0.000265] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000276] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000286] ... MAX_LOCK_DEPTH: 48
[ 0.000294] ... MAX_LOCKDEP_KEYS: 8192
[ 0.000303] ... CLASSHASH_SIZE: 4096
[ 0.000313] ... MAX_LOCKDEP_ENTRIES: 32768
[ 0.000321] ... MAX_LOCKDEP_CHAINS: 65536
[ 0.000330] ... CHAINHASH_SIZE: 32768
[ 0.000338] memory used by lock dependency info: 1861 kB
[ 0.000349] per task-struct memory footprint: 1536 bytes
[ 0.000416] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000447] CPU: Testing write buffer coherency: ok
[ 0.000531] pid_max: default: 32768 minimum: 301
[ 0.001342] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001368] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.004079] qcom_scm: convention: smc legacy
[ 0.005840] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.006171] rcu: Hierarchical SRCU implementation.
[ 0.006183] rcu: Max phase no-delay instances is 1000.
[ 0.007609] smp: Bringing up secondary CPUs ...
[ 0.010987] smp: Brought up 1 node, 2 CPUs
[ 0.011009] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.011024] CPU: All CPU(s) started in SVC mode.
[ 0.037527] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.037963] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.038003] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.038423] pinctrl core: initialized pinctrl subsystem
[ 0.042521] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.043236] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.046770] thermal_sys: Registered thermal governor 'step_wise'
[ 0.047082] cpuidle: using governor ladder
[ 0.047228] cpuidle: using governor menu
[ 0.111584] cryptd: max_cpu_qlen set to 1000
[ 0.116291] pps_core: LinuxPPS API ver. 1 registered
[ 0.116307] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.116365] PTP clock support registered
[ 0.119705] mctp: management component transport protocol core
[ 0.119722] NET: Registered PF_MCTP protocol family
[ 0.120931] clocksource: Switched to clocksource dg_timer
[ 0.122017] VFS: Disk quotas dquot_6.6.0
[ 0.122189] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.124624] NET: Registered PF_INET protocol family
[ 0.125000] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.127221] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 10240 bytes, linear)
[ 0.127306] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.127348] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.127473] TCP bind hash table entries: 4096 (order: 6, 327680 bytes, linear)
[ 0.129021] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.129789] MPTCP token hash table entries: 512 (order: 2, 24576 bytes, linear)
[ 0.130035] UDP hash table entries: 256 (order: 2, 24576 bytes, linear)
[ 0.130179] UDP-Lite hash table entries: 256 (order: 2, 24576 bytes, linear)
[ 0.130792] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.130983] PCI: CLS 0 bytes, default 64
[ 0.140792] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.157691] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.277165] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[ 0.277738] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[ 0.278014] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.278626] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.278691] qcom-pcie 1b500000.pci: Parsing ranges property...
[ 0.278760] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fe0ffff -> 0x0000000000
[ 0.278888] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[ 0.404115] qcom-pcie 1b500000.pci: Using 32 MSI vectors
[ 0.404509] qcom-pcie 1b500000.pci: iATU unroll: disabled
[ 0.404531] qcom-pcie 1b500000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[ 0.507346] qcom-pcie 1b500000.pci: PCIe Gen.1 x1 link up
[ 0.507765] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.507794] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.507818] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.507836] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.507856] pci_bus 0000:00: scanning bus
[ 0.508037] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.508294] pci 0000:00:00.0: supports D1
[ 0.508314] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.508384] pci 0000:00:00.0: PME# disabled
[ 0.512325] pci_bus 0000:00: fixups for bus
[ 0.512359] PCI: bus0: Fast back to back transfers disabled
[ 0.512383] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.512632] pci_bus 0000:01: scanning bus
[ 0.512912] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.513213] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.514623] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.514681] pci 0000:01:00.0: PME# disabled
[ 0.515105] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 0.516140] pci_bus 0000:01: fixups for bus
[ 0.516232] PCI: bus1: Fast back to back transfers disabled
[ 0.516250] pci_bus 0000:01: bus scan returning with max=01
[ 0.516275] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.516301] pci_bus 0000:00: bus scan returning with max=ff
[ 0.516337] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.516370] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.516524] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.516553] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.516957] pcieport 0000:00:00.0: assign IRQ: got 27
[ 0.517395] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x43c00000
[ 0.518778] pcieport 0000:00:00.0: AER: enabled with IRQ 28
[ 0.519000] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 0.519025] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 0.519044] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 0.519061] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 0.519078] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 0.519097] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 0.519116] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 0.519133] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 0.519149] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x8100800)
[ 0.519167] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 0.519185] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 0.519202] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 0.519218] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 0.519236] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 0.519253] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 0.519271] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3011b)
[ 0.520498] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[ 0.520944] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[ 0.521273] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.521830] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 0.521890] qcom-pcie 1b700000.pci: Parsing ranges property...
[ 0.521960] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031e0ffff -> 0x0000000000
[ 0.522023] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[ 0.644072] qcom-pcie 1b700000.pci: Using 32 MSI vectors
[ 0.644395] qcom-pcie 1b700000.pci: iATU unroll: disabled
[ 0.644413] qcom-pcie 1b700000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[ 0.747177] qcom-pcie 1b700000.pci: PCIe Gen.2 x1 link up
[ 0.747496] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.747521] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.747548] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
[ 0.747568] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.747585] pci_bus 0001:00: scanning bus
[ 0.747656] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.747849] pci 0001:00:00.0: supports D1
[ 0.747866] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.747888] pci 0001:00:00.0: PME# disabled
[ 0.751746] pci_bus 0001:00: fixups for bus
[ 0.751781] PCI: bus0: Fast back to back transfers disabled
[ 0.751802] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.752135] pci_bus 0001:01: scanning bus
[ 0.752400] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.752679] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.753990] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.754045] pci 0001:01:00.0: PME# disabled
[ 0.755441] pci_bus 0001:01: fixups for bus
[ 0.755526] PCI: bus1: Fast back to back transfers disabled
[ 0.755544] pci_bus 0001:01: bus scan returning with max=01
[ 0.755566] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.755591] pci_bus 0001:00: bus scan returning with max=ff
[ 0.755624] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.755656] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.755800] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.755830] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.756166] pcieport 0001:00:00.0: assign IRQ: got 30
[ 0.756417] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x43c09000
[ 0.757248] pcieport 0001:00:00.0: AER: enabled with IRQ 31
[ 0.757512] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 0.757536] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 0.757553] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 0.757570] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 0.757587] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 0.757607] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 0.757624] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 0.757642] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 0.757660] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
[ 0.757677] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 0.757693] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 0.757710] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 0.757727] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 0.757743] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 0.757760] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 0.757777] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x3011e)
[ 1.064930] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[ 1.064958] krait-cc soc:clock-controller: CPU1 @ Undefined rate. Forcing new rate.
[ 1.065221] krait-cc soc:clock-controller: CPU1 @ 800000 KHz
[ 1.065241] krait-cc soc:clock-controller: L2 @ Undefined rate. Forcing new rate.
[ 1.065521] krait-cc soc:clock-controller: L2 @ 800000 KHz
[ 1.074421] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 1.077436] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.079385] msm_serial 16340000.serial: msm_serial: detected port #0
[ 1.079446] msm_serial 16340000.serial: uartclk = 7372800
[ 1.079650] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 35, base_baud = 460800) is a MSM
[ 1.079760] msm_serial: console setup on port #0
[ 2.022024] printk: console [ttyMSM0] enabled
[ 2.027557] msm_serial: driver initialized
[ 2.042618] loop: module loaded
[ 2.045182] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 2.045224] nand: AMD/Spansion S34MS01G2
[ 2.051171] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.511497] random: crng init done
[ 2.724240] found squashfs at 1380000 with len of 23068672 bytes
[ 3.225754] found squashfs at 3A80000 with len of 21757952 bytes
[ 3.225814] 19 fixed-partitions partitions found on MTD device qcom_nand.0
[ 3.230879] Creating 19 MTD partitions on "qcom_nand.0":
[ 3.237613] 0x000000000000-0x000000040000 : "SBL1"
[ 3.247782] 0x000000040000-0x000000180000 : "MIBIB"
[ 3.251149] 0x000000180000-0x0000002c0000 : "SBL2"
[ 3.255753] 0x0000002c0000-0x000000540000 : "SBL3"
[ 3.263014] 0x000000540000-0x000000660000 : "DDRCONFIG"
[ 3.266114] 0x000000660000-0x000000780000 : "SSD"
[ 3.270135] 0x000000780000-0x000000a00000 : "TZ"
[ 3.277718] 0x000000a00000-0x000000c80000 : "RPM"
[ 3.283530] 0x000000c80000-0x000000dc0000 : "art"
[ 3.286813] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[ 3.290014] 0x000000ec0000-0x000000f00000 : "u_env"
[ 3.293664] 0x000000f00000-0x000000f40000 : "s_env"
[ 3.298230] 0x000000f40000-0x000000f80000 : "devinfo"
[ 3.303201] 0x000000f80000-0x000003780000 : "linux"
[ 3.385791] 0x000001380000-0x000002980000 : "rootfs"
[ 3.429416] mtd: setting mtd14 (rootfs) as root device
[ 3.429549] 0x000003780000-0x000005f40000 : "linux2"
[ 3.511447] 0x000003a80000-0x000004f40000 : "rootfs2"
[ 3.552563] 0x000005f40000-0x000005f80000 : "nvram"
[ 3.553912] 0x000005f80000-0x000008000000 : "ddwrt"
[ 3.676823] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[ 4.477974] ar8327: qca,phy-rgmii-en is not specified
[ 4.479717] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[ 4.482152] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[ 4.489553] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 4.496737] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 4.502166] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 4.509535] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 4.515427] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 4.523137] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 4.530973] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 4.536850] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 4.544268] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 4.550942] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 4.558565] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 4.565591] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 4.571788] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address 6a:cd:b7:62:c3:a8
[ 4.583858] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[ 4.588100] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[ 4.595733] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 4.602572] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 4.608243] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 4.615781] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 4.621650] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 4.629244] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 4.637224] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 4.643036] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 4.650334] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 4.657188] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 4.664727] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 4.671747] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 4.677865] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address 92:3f:c1:0c:08:e8
[ 4.689601] PPP generic driver version 2.4.2
[ 4.694678] PPP BSD Compression module registered
[ 4.698690] PPP Deflate Compression module registered
[ 4.703812] PPP MPPE Compression module registered
[ 4.708324] NET: Registered PF_PPPOX protocol family
[ 4.713467] i2c_dev: i2c /dev entries driver
[ 4.726459] GACT probability NOT on
[ 4.726526] Mirror/redirect action on
[ 4.728856] Simple TC action Loaded
[ 4.733859] netem: version 1.3
[ 4.735952] u32 classifier
[ 4.739003] Performance counters on
[ 4.741787] input device check on
[ 4.745431] Actions configured
[ 4.750753] nf_conntrack_rtsp v0.7 loading
[ 4.753962] xt_time: kernel timezone is -0000
[ 4.757073] gre: GRE over IPv4 demultiplexor driver
[ 4.762387] NET: Registered PF_INET6 protocol family
[ 4.768574] Segment Routing with IPv6
[ 4.770992] In-situ OAM (IOAM) with IPv6
[ 4.774812] NET: Registered PF_PACKET protocol family
[ 4.778843] Bridge firewalling registered
[ 4.783524] 8021q: 802.1Q VLAN Support v1.8
[ 4.787673] Registering SWP/SWPB emulation handler
[ 4.795738] registered taskstats version 1
[ 4.864235] Failed to get APPS FABRIC clock
[ 4.867786] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 4.895215] s1a: Bringing 0uV into 1050000-1050000uV
[ 4.896075] s1b: Bringing 0uV into 1050000-1050000uV
[ 4.899896] s2a: Bringing 0uV into 800000-800000uV
[ 4.905184] s2b: Bringing 0uV into 800000-800000uV
[ 4.921288] thermal thermal_zone0: failed to read out thermal zone (-110)
[ 4.946402] searching for nvram
[ 4.946461] nvram size = 262144
[ 5.008975] found nvram at 20000
[ 5.040973] UBI error: no valid UBI magic found inside mtd13
[ 5.054960] VFS: Mounted root (squashfs filesystem) readonly on device 31:14.
[ 5.055666] Freeing unused kernel image (initmem) memory: 1024K
[ 5.061451] Run /sbin/init as init process
[ 5.066804] with arguments:
[ 5.066809] /sbin/init
[ 5.066815] with environment:
[ 5.066821] HOME=/
[ 5.066826] TERM=linux
[ 10.298244] ath9k: ath9k: Driver unloaded
[ 10.716568] ath10k_pci 0000:01:00.0: assign IRQ: got 27
[ 10.717411] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 10.717515] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 10.718374] qcom-pcie 1b500000.pci: msi#1 address_hi 0x0 address_lo 0x43c00000
[ 10.718568] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.053101] ath10k_pci 0000:01:00.0: found firmware features ie (8 B)
[ 11.053149] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 11.058534] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0
[ 11.069812] ath10k_pci 0000:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7736M api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 0c4006b8
[ 11.134086] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[ 11.137387] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 11.143398] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 11.166287] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 e4a0f655
[ 11.187570] ath10k_pci 0000:01:00.0: boot already acquired valid otp board id,skip download, board_id 2 chip_id 1
[ 11.208123] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11240
[ 12.139380] ath10k_pci 0000:01:00.0: Init Max Stations to 64
[ 12.140061] ath10k_pci 0000:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000002 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2500 low_5ghz_chan 4800 high_5ghz_chan 6115 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 12.231177] ath10k_pci 0000:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 1 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0 c
[ 12.232075] ath10k_pci 0000:01:00.0: free: 23264 iram: 29408 sram: 19112
[ 12.242572] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[ 12.280857] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 12.366210] ath10k_pci 0000:01:00.0: init channel number 86
[ 12.372689] ath10k_pci 0001:01:00.0: assign IRQ: got 30
[ 12.373523] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 12.373631] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 12.374274] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x43c09000
[ 12.374450] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 12.533283] ath10k_pci 0001:01:00.0: found firmware features ie (8 B)
[ 12.533327] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 12.538710] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0
[ 12.550190] ath10k_pci 0001:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7736M api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 0c4006b8
[ 12.614032] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[ 12.617332] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 12.623366] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 12.632930] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 e4a0f655
[ 12.662103] ath10k_pci 0001:01:00.0: boot already acquired valid otp board id,skip download, board_id 1 chip_id 1
[ 12.682551] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11240
[ 13.609553] ath10k_pci 0001:01:00.0: Init Max Stations to 64
[ 13.610243] ath10k_pci 0001:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000001 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2500 low_5ghz_chan 4800 high_5ghz_chan 6115 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 13.699176] ath10k_pci 0001:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 2 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0 c
[ 13.700032] ath10k_pci 0001:01:00.0: free: 23264 iram: 29408 sram: 19112
[ 13.710571] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[ 13.747866] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 13.836074] ath10k_pci 0001:01:00.0: init channel number 281
[ 14.975509] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 14.986283] dwmac1000: Master AXI performs any burst length
[ 14.986314] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 15.000670] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 15.000972] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 15.009484] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 15.016248] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.024272] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.036381] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.049639] dwmac1000: Master AXI performs any burst length
[ 15.049670] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 15.064168] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 15.064390] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 15.072936] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 15.079262] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.090194] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 17.759716] device br0 entered promiscuous mode
[ 17.823812] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[ 17.841885] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 17.852662] dwmac1000: Master AXI performs any burst length
[ 17.852694] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 17.867049] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 17.867255] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 17.874990] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 17.882101] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 17.890452] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.907620] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[ 17.919462] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 17.930296] dwmac1000: Master AXI performs any burst length
[ 17.930328] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 17.944762] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 17.944964] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 17.952684] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 17.959648] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 17.968268] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.979633] br0: port 1(eth0) entered blocking state
[ 17.988301] br0: port 1(eth0) entered disabled state
[ 17.993821] device eth0 entered promiscuous mode
[ 17.998500] br0: port 1(eth0) entered blocking state
[ 18.003041] br0: port 1(eth0) entered forwarding state
[ 18.008019] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[ 18.025912] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 18.042675] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 18.053450] dwmac1000: Master AXI performs any burst length
[ 18.053483] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 18.067840] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 18.068050] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 18.075768] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 18.082819] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 18.091655] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 18.108325] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 18.120113] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 18.130889] dwmac1000: Master AXI performs any burst length
[ 18.130920] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 18.145352] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 18.145552] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 18.153276] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 18.160485] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 18.168849] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 18.180043] br0: port 2(eth1) entered blocking state
[ 18.183666] br0: port 2(eth1) entered disabled state
[ 18.189140] device eth1 entered promiscuous mode
[ 18.193889] br0: port 2(eth1) entered blocking state
[ 18.198338] br0: port 2(eth1) entered forwarding state
[ 18.219240] device br0 left promiscuous mode
[ 18.223752] device br0 entered promiscuous mode
[ 18.237295] device br0 left promiscuous mode
[ 22.016807] ksmbd: unknown parameter 'connlimit' ignored
[ 24.905163] usbcore: registered new interface driver usbfs
[ 24.905488] usbcore: registered new interface driver hub
[ 24.909667] usbcore: registered new device driver usb
[ 25.903239] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.903471] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 25.907976] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 25.915333] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x11000000
[ 25.925184] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.930478] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 25.936103] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 25.944511] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 25.950161] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.958500] usb usb1: Product: xHCI Host Controller
[ 25.965678] usb usb1: Manufacturer: Linux 6.1.84 xhci-hcd
[ 25.970382] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 25.977015] hub 1-0:1.0: USB hub found
[ 25.980704] hub 1-0:1.0: 1 port detected
[ 25.985569] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.988809] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 25.996671] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 26.004781] usb usb2: Product: xHCI Host Controller
[ 26.012149] usb usb2: Manufacturer: Linux 6.1.84 xhci-hcd
[ 26.016654] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 26.023253] hub 2-0:1.0: USB hub found
[ 26.026973] hub 2-0:1.0: 1 port detected
[ 26.100356] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 26.100416] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 26.105125] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 26.112459] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x10000000
[ 26.122146] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 26.127590] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 26.133228] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 26.142524] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 26.147280] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 26.155627] usb usb3: Product: xHCI Host Controller
[ 26.162809] usb usb3: Manufacturer: Linux 6.1.84 xhci-hcd
[ 26.167499] usb usb3: SerialNumber: xhci-hcd.1.auto
[ 26.173848] hub 3-0:1.0: USB hub found
[ 26.177811] hub 3-0:1.0: 1 port detected
[ 26.182374] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 26.189854] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 26.197912] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 26.205950] usb usb4: Product: xHCI Host Controller
[ 26.213129] usb usb4: Manufacturer: Linux 6.1.84 xhci-hcd
[ 26.217844] usb usb4: SerialNumber: xhci-hcd.1.auto
[ 26.224273] hub 4-0:1.0: USB hub found
[ 26.228150] hub 4-0:1.0: 1 port detected
[ 26.602296] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 27.581483] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 27.622572] usb 2-1: New USB device found, idVendor=090c, idProduct=2000, bcdDevice=11.00
[ 27.622609] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 27.629730] usb 2-1: Product: Flash Disk
[ 27.636951] usb 2-1: Manufacturer: USB
[ 31.413903] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 31.414146] usb usb4: USB disconnect, device number 1
[ 31.419066] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 31.423088] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 31.428714] usb usb3: USB disconnect, device number 1
[ 31.435553] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 31.438797] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 31.444518] usb usb2: USB disconnect, device number 1
[ 31.449369] usb 2-1: USB disconnect, device number 2
[ 31.456692] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 31.459460] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 31.465188] usb usb1: USB disconnect, device number 1
[ 31.471861] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 31.559018] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 31.559080] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 31.563716] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 31.570990] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x11000000
[ 31.580816] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 31.586303] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 31.591850] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 31.599687] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 31.606013] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 31.614303] usb usb1: Product: xHCI Host Controller
[ 31.621460] usb usb1: Manufacturer: Linux 6.1.84 xhci-hcd
[ 31.626159] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 31.632400] hub 1-0:1.0: USB hub found
[ 31.636480] hub 1-0:1.0: 1 port detected
[ 31.640926] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 31.644691] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 31.652461] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 31.660449] usb usb2: Product: xHCI Host Controller
[ 31.667746] usb usb2: Manufacturer: Linux 6.1.84 xhci-hcd
[ 31.672524] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 31.678661] hub 2-0:1.0: USB hub found
[ 31.682834] hub 2-0:1.0: 1 port detected
[ 31.687271] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 31.690611] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 31.696174] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 31.703533] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x10000000
[ 31.713266] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 31.718711] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 31.724354] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 31.732199] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 31.738404] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 31.746741] usb usb3: Product: xHCI Host Controller
[ 31.753920] usb usb3: Manufacturer: Linux 6.1.84 xhci-hcd
[ 31.758625] usb usb3: SerialNumber: xhci-hcd.1.auto
[ 31.764913] hub 3-0:1.0: USB hub found
[ 31.768953] hub 3-0:1.0: 1 port detected
[ 31.773446] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 31.777073] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 31.784920] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 31.792981] usb usb4: Product: xHCI Host Controller
[ 31.800118] usb usb4: Manufacturer: Linux 6.1.84 xhci-hcd
[ 31.804977] usb usb4: SerialNumber: xhci-hcd.1.auto
[ 31.811432] hub 4-0:1.0: USB hub found
[ 31.815211] hub 4-0:1.0: 1 port detected
[ 32.072115] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 32.112529] usb 2-1: New USB device found, idVendor=090c, idProduct=2000, bcdDevice=11.00
[ 32.112568] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 32.119692] usb 2-1: Product: Flash Disk
[ 32.126906] usb 2-1: Manufacturer: USB
[ 32.647344] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 32.648134] usb-storage 2-1:1.0: Quirks match for vid 090c pid 2000: 800000
[ 32.653489] usbcore: registered new interface driver usb-storage
[ 32.714729] usbcore: registered new interface driver uas
[ 32.989277] ahci 29000000.sata: supply ahci not found, using dummy regulator
[ 32.989568] ahci 29000000.sata: supply phy not found, using dummy regulator
[ 32.995683] ahci 29000000.sata: supply target not found, using dummy regulator
[ 33.768568] sda: sda1
[ 34.783473] br1: port 1(eth1.15) entered blocking state
[ 34.783514] br1: port 1(eth1.15) entered disabled state
[ 34.788088] device eth1.15 entered promiscuous mode
[ 34.797935] br1: port 1(eth1.15) entered blocking state
[ 36.782449] ksmbd: unknown parameter 'connlimit' ignored
[ 54.528895] br1: port 1(eth1.15) entered learning state
[ 69.527945] br1: port 1(eth1.15) entered forwarding state
[ 406.071522] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead.
root@EA8500:~# uptime && date
10:16:09 up 39 min, load average: 0.01, 0.02, 0.00
Thu Apr 11 10:16:09 CDT 2024
root@EA8500:~#
Connection to ea8500.mrjcd.com closed.
mrjcd@daDeb:~$