mrjcd@daDeb:~$ ssh root@ea8500.mrjcd.com
DD-WRT v3.0-r53763 std (c) 2023 NewMedia-NET GmbH
Release: 10/24/23
Board: Linksys EA8500
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
https://www.dd-wrt.com
==========================================================
BusyBox v1.36.1 (2023-10-24 06:21:26 +07) built-in shell (ash)
root@EA8500:~# dmesg | grep scsi
[ 27.252570] scsi host0: usb-storage 1-1:1.0
[ 27.261600] scsi host1: usb-storage 4-1:1.0
[ 27.524590] scsi host2: ahci
[ 28.332266] scsi 0:0:0:0: Direct-Access USB Flash Drive 1.00 PQ: 0 ANSI: 6
[ 28.525536] scsi 1:0:0:0: Direct-Access Samsung Flash Drive 1100 PQ: 0 ANSI: 6
root@EA8500:~# df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 22016 22016 0 100% /
none 512 0 512 0% /dev
/dev/sda1 14965728 6018792 8164908 42% /tmp/mnt/sda1
root@EA8500:~# blkid
/dev/sda1: LABEL="16GBext4" UUID="0cfdee24-2710-4fff-a543-0f8afb91a82f"
root@EA8500:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 6.1.59 (root@server2) (arm-openwrt-linux-gcc (OpenWrt GCC 13.2.0 r24111-66f6c20e45) 13.2.0, GNU ld (GNU Binutils) 2.41) # SMP
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys EA8500 WiFi Router
[ 0.000000] OF: fdt: Ignoring memory range 0x41500000 - 0x42000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s15124 r8192 d21740 u45056
[ 0.000000] pcpu-alloc: s15124 r8192 d21740 u45056 alloc=11*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 474732K/491520K available (8530K kernel code, 674K rwdata, 992K rodata, 1024K init, 373K bss, 16788K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000002] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000020] Switching to timer-based delay loop, resolution 160ns
[ 0.000257] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000281] CPU: Testing write buffer coherency: ok
[ 0.000335] pid_max: default: 32768 minimum: 301
[ 0.000906] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000931] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.002354] qcom_scm: convention: smc legacy
[ 0.003129] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.003291] rcu: Hierarchical SRCU implementation.
[ 0.003299] rcu: Max phase no-delay instances is 1000.
[ 0.003811] smp: Bringing up secondary CPUs ...
[ 0.005666] smp: Brought up 1 node, 2 CPUs
[ 0.005684] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.005694] CPU: All CPU(s) started in SVC mode.
[ 0.016241] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.016398] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.016434] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.016598] pinctrl core: initialized pinctrl subsystem
[ 0.018534] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.018944] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.020323] thermal_sys: Registered thermal governor 'step_wise'
[ 0.020635] cpuidle: using governor ladder
[ 0.020773] cpuidle: using governor menu
[ 0.057310] pps_core: LinuxPPS API ver. 1 registered
[ 0.057323] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.057387] PTP clock support registered
[ 0.059108] mctp: management component transport protocol core
[ 0.059120] NET: Registered PF_MCTP protocol family
[ 0.059897] cryptd: max_cpu_qlen set to 1000
[ 0.060596] clocksource: Switched to clocksource dg_timer
[ 0.061077] VFS: Disk quotas dquot_6.6.0
[ 0.061188] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.062497] NET: Registered PF_INET protocol family
[ 0.062748] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.064230] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.064266] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.064358] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.064401] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.064484] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.064768] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.064871] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.064899] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.065159] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.065212] PCI: CLS 0 bytes, default 64
[ 0.070441] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.076912] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.080756] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[ 0.081067] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[ 0.081163] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.081441] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.081487] qcom-pcie 1b500000.pci: Parsing ranges property...
[ 0.081531] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fe0ffff -> 0x0000000000
[ 0.081574] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[ 0.203749] qcom-pcie 1b500000.pci: Using 32 MSI vectors
[ 0.203900] qcom-pcie 1b500000.pci: iATU unroll: disabled
[ 0.203914] qcom-pcie 1b500000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[ 0.306699] qcom-pcie 1b500000.pci: PCIe Gen.1 x1 link up
[ 0.306904] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.306921] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.306939] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.306954] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.306969] pci_bus 0000:00: scanning bus
[ 0.307025] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.307186] pci 0000:00:00.0: supports D1
[ 0.307200] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.307217] pci 0000:00:00.0: PME# disabled
[ 0.310338] pci_bus 0000:00: fixups for bus
[ 0.310365] PCI: bus0: Fast back to back transfers disabled
[ 0.310379] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.310513] pci_bus 0000:01: scanning bus
[ 0.310878] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.311171] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.312518] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.312569] pci 0000:01:00.0: PME# disabled
[ 0.312971] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 0.313764] pci_bus 0000:01: fixups for bus
[ 0.313849] PCI: bus1: Fast back to back transfers disabled
[ 0.313860] pci_bus 0000:01: bus scan returning with max=01
[ 0.313880] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.313900] pci_bus 0000:00: bus scan returning with max=ff
[ 0.313932] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.313956] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.314106] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.314128] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.314352] pcieport 0000:00:00.0: assign IRQ: got 27
[ 0.314482] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x43740000
[ 0.315228] pcieport 0000:00:00.0: AER: enabled with IRQ 28
[ 0.315347] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 0.315367] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 0.315380] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 0.315395] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 0.315407] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 0.315423] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 0.315435] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 0.315447] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 0.315460] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x8100800)
[ 0.315473] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 0.315485] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 0.315499] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 0.315512] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 0.315526] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 0.315538] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 0.315551] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3011b)
[ 0.316266] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[ 0.316525] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[ 0.316649] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.316929] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 0.316973] qcom-pcie 1b700000.pci: Parsing ranges property...
[ 0.317019] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031e0ffff -> 0x0000000000
[ 0.317057] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[ 0.443885] qcom-pcie 1b700000.pci: Using 32 MSI vectors
[ 0.444036] qcom-pcie 1b700000.pci: iATU unroll: disabled
[ 0.444050] qcom-pcie 1b700000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[ 0.546744] qcom-pcie 1b700000.pci: PCIe Gen.2 x1 link up
[ 0.546968] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.546987] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.547008] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
[ 0.547023] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.547038] pci_bus 0001:00: scanning bus
[ 0.547087] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.547225] pci 0001:00:00.0: supports D1
[ 0.547238] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.547254] pci 0001:00:00.0: PME# disabled
[ 0.550326] pci_bus 0001:00: fixups for bus
[ 0.550349] PCI: bus0: Fast back to back transfers disabled
[ 0.550366] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.550548] pci_bus 0001:01: scanning bus
[ 0.550893] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.551163] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.552412] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.552460] pci 0001:01:00.0: PME# disabled
[ 0.553515] pci_bus 0001:01: fixups for bus
[ 0.553593] PCI: bus1: Fast back to back transfers disabled
[ 0.553605] pci_bus 0001:01: bus scan returning with max=01
[ 0.553623] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.553642] pci_bus 0001:00: bus scan returning with max=ff
[ 0.553666] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.553689] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.553829] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.553853] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.554073] pcieport 0001:00:00.0: assign IRQ: got 30
[ 0.554200] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x43749000
[ 0.554656] pcieport 0001:00:00.0: AER: enabled with IRQ 31
[ 0.554775] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 0.554793] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 0.554806] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 0.554819] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 0.554831] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 0.554845] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 0.554858] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 0.554871] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 0.554883] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
[ 0.554896] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 0.554908] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 0.554920] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 0.554932] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 0.554944] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 0.554956] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 0.554968] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x3011e)
[ 0.558868] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[ 0.558889] krait-cc soc:clock-controller: CPU1 @ Undefined rate. Forcing new rate.
[ 0.559036] krait-cc soc:clock-controller: CPU1 @ 384000 KHz
[ 0.559054] krait-cc soc:clock-controller: L2 @ Undefined rate. Forcing new rate.
[ 0.559256] krait-cc soc:clock-controller: L2 @ 384000 KHz
[ 0.564688] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.566894] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.568226] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.568278] msm_serial 16340000.serial: uartclk = 7372800
[ 0.568447] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 35, base_baud = 460800) is a MSM
[ 0.568486] msm_serial: console setup on port #0
[ 1.458677] printk: console [ttyMSM0] enabled
[ 1.463981] msm_serial: driver initialized
[ 1.473634] loop: module loaded
[ 1.475308] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 1.475598] nand: AMD/Spansion S34MS01G2
[ 1.482283] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.841000] random: crng init done
[ 2.029125] found squashfs at 1380000 with len of 22413312 bytes
[ 2.436486] found squashfs at 3A80000 with len of 21757952 bytes
[ 2.436540] 19 fixed-partitions partitions found on MTD device qcom_nand.0
[ 2.441654] Creating 19 MTD partitions on "qcom_nand.0":
[ 2.448252] 0x000000000000-0x000000040000 : "SBL1"
[ 2.457254] 0x000000040000-0x000000180000 : "MIBIB"
[ 2.460753] 0x000000180000-0x0000002c0000 : "SBL2"
[ 2.465652] 0x0000002c0000-0x000000540000 : "SBL3"
[ 2.472404] 0x000000540000-0x000000660000 : "DDRCONFIG"
[ 2.475024] 0x000000660000-0x000000780000 : "SSD"
[ 2.480094] 0x000000780000-0x000000a00000 : "TZ"
[ 2.487332] 0x000000a00000-0x000000c80000 : "RPM"
[ 2.491791] 0x000000c80000-0x000000dc0000 : "art"
[ 2.494445] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[ 2.498756] 0x000000ec0000-0x000000f00000 : "u_env"
[ 2.502690] 0x000000f00000-0x000000f40000 : "s_env"
[ 2.507207] 0x000000f40000-0x000000f80000 : "devinfo"
[ 2.512107] 0x000000f80000-0x000003780000 : "linux"
[ 2.580399] 0x000001380000-0x0000028e0000 : "rootfs"
[ 2.615220] mtd: setting mtd14 (rootfs) as root device
[ 2.615786] 1 squashfs-split partitions found on MTD device rootfs
[ 2.619265] 0x0000028e0000-0x000008000000 : "rootfs_data"
[ 2.766492] 0x000003780000-0x000005f40000 : "linux2"
[ 2.830127] 0x000003a80000-0x000004f40000 : "rootfs2"
[ 2.863619] 0x000005f40000-0x000005f80000 : "nvram"
[ 2.864527] 0x000005f80000-0x000008000000 : "ddwrt"
[ 2.951073] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[ 3.787016] ar8327: qca,phy-rgmii-en is not specified
[ 3.788256] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[ 3.791160] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[ 3.798424] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 3.805212] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 3.811210] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 3.818574] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 3.824472] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 3.832185] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 3.840013] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 3.845898] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 3.853283] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 3.859978] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 3.867611] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 3.874639] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.880739] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address a6:2c:95:af:13:57
[ 3.893780] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[ 3.897139] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[ 3.904703] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 3.911191] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 3.917276] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 3.924822] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 3.930554] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 3.938337] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 3.946241] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 3.952052] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 3.959369] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 3.966214] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 3.973764] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 3.980723] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.986981] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address 5a:7c:b1:24:4c:50
[ 3.999319] PPP generic driver version 2.4.2
[ 4.003497] PPP BSD Compression module registered
[ 4.007722] PPP Deflate Compression module registered
[ 4.012912] PPP MPPE Compression module registered
[ 4.017358] NET: Registered PF_PPPOX protocol family
[ 4.022440] i2c_dev: i2c /dev entries driver
[ 4.032457] GACT probability NOT on
[ 4.032510] Mirror/redirect action on
[ 4.034814] Simple TC action Loaded
[ 4.039270] netem: version 1.3
[ 4.042025] u32 classifier
[ 4.044998] Performance counters on
[ 4.047691] input device check on
[ 4.051499] Actions configured
[ 4.055972] nf_conntrack_rtsp v0.7 loading
[ 4.058936] xt_time: kernel timezone is -0000
[ 4.063029] gre: GRE over IPv4 demultiplexor driver
[ 4.067600] NET: Registered PF_INET6 protocol family
[ 4.073519] Segment Routing with IPv6
[ 4.076974] In-situ OAM (IOAM) with IPv6
[ 4.080657] NET: Registered PF_PACKET protocol family
[ 4.084704] Bridge firewalling registered
[ 4.089448] 8021q: 802.1Q VLAN Support v1.8
[ 4.205566] Registering SWP/SWPB emulation handler
[ 4.205857] registered taskstats version 1
[ 4.232532] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 4.246106] s1a: Bringing 0uV into 1050000-1050000uV
[ 4.246589] s1b: Bringing 0uV into 1050000-1050000uV
[ 4.250564] s2a: Bringing 0uV into 800000-800000uV
[ 4.255587] s2b: Bringing 0uV into 800000-800000uV
[ 4.270950] thermal thermal_zone0: failed to read out thermal zone (-110)
[ 4.286161] searching for nvram
[ 4.286205] nvram size = 262144
[ 4.337057] found nvram at 20000
[ 4.362635] UBI error: no valid UBI magic found inside mtd13
[ 4.378055] VFS: Mounted root (squashfs filesystem) readonly on device 31:14.
[ 4.378641] Freeing unused kernel image (initmem) memory: 1024K
[ 4.431060] Run /sbin/init as init process
[ 4.431080] with arguments:
[ 4.431085] /sbin/init
[ 4.431089] with environment:
[ 4.431092] HOME=/
[ 4.431097] TERM=linux
[ 7.908246] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace
[ 7.908283] Backport generated by backports.git v5.15.33-1-0-g183c4ab2
[ 8.293210] ath9k: ath9k: Driver unloaded
[ 8.613672] ath10k_pci 0000:01:00.0: assign IRQ: got 27
[ 8.614134] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 8.614232] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 8.614757] qcom-pcie 1b500000.pci: msi#1 address_hi 0x0 address_lo 0x43740000
[ 8.614928] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 8.927921] ath10k_pci 0000:01:00.0: found firmware features ie (8 B)
[ 8.927962] ath10k_pci 0000:01:00.0: Unknown FW IE: 30
[ 8.933427] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 8.938385] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[ 8.949256] ath10k_pci 0000:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7264 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 39c77aba
[ 9.014012] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[ 9.017309] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 9.023304] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 9.043934] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 e4a0f655
[ 9.065045] ath10k_pci 0000:01:00.0: boot already acquired valid otp board id,skip download, board_id 2 chip_id 1
[ 9.085604] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11240
[ 10.148717] ath10k_pci 0000:01:00.0: Init Max Stations to 64
[ 10.149302] ath10k_pci 0000:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000002 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 10.240638] ath10k_pci 0000:01:00.0: wmi debug print truncated: 128
[ 10.240664] ath10k_pci 0000:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 1 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0 c
[ 10.245836] ath10k_pci 0000:01:00.0: free: 18212 iram: 32064 sram: 17864
[ 10.258282] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[ 10.296249] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 10.384968] ath10k_pci 0000:01:00.0: init channel number 86
[ 10.385003] ath: EEPROM regdomain sanitized
[ 10.385010] ath: EEPROM regdomain: 0x64
[ 10.385016] ath: EEPROM indicates we should expect a direct regpair map
[ 10.385025] ath: Country alpha2 being used: 00
[ 10.385031] ath: Regpair used: 0x64
[ 10.385066] initialize fq_codel with 33554432 bytes memory limit
[ 10.389429] ieee80211_txq_setup_flows: set limit to 4194304 bytes
[ 10.398845] ath10k_pci 0001:01:00.0: assign IRQ: got 30
[ 10.399819] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 10.401755] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 10.402230] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x43749000
[ 10.402391] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 10.562820] ath10k_pci 0001:01:00.0: found firmware features ie (8 B)
[ 10.562858] ath10k_pci 0001:01:00.0: Unknown FW IE: 30
[ 10.568245] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 10.573337] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[ 10.584488] ath10k_pci 0001:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7264 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 39c77aba
[ 10.648650] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[ 10.651943] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 10.657890] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 10.667554] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 e4a0f655
[ 10.696693] ath10k_pci 0001:01:00.0: boot already acquired valid otp board id,skip download, board_id 1 chip_id 1
[ 10.717170] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11240
[ 11.777308] ath10k_pci 0001:01:00.0: Init Max Stations to 64
[ 11.777916] ath10k_pci 0001:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000001 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 11.867023] ath10k_pci 0001:01:00.0: wmi debug print truncated: 128
[ 11.867051] ath10k_pci 0001:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 2 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0 c
[ 11.872207] ath10k_pci 0001:01:00.0: free: 18212 iram: 32064 sram: 17864
[ 11.884668] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[ 11.921509] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 12.004998] ath10k_pci 0001:01:00.0: init channel number 134
[ 12.005036] ath: EEPROM regdomain sanitized
[ 12.005041] ath: EEPROM regdomain: 0x64
[ 12.005048] ath: EEPROM indicates we should expect a direct regpair map
[ 12.005056] ath: Country alpha2 being used: 00
[ 12.005061] ath: Regpair used: 0x64
[ 12.005096] initialize fq_codel with 33554432 bytes memory limit
[ 12.009804] ieee80211_txq_setup_flows: set limit to 33554432 bytes
[ 12.967729] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 12.978449] dwmac1000: Master AXI performs any burst length
[ 12.978476] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 12.992906] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 12.993028] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 13.001224] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 13.007845] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 13.017226] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 13.027612] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 13.041951] dwmac1000: Master AXI performs any burst length
[ 13.041978] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 13.056335] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 13.056456] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 13.064686] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 13.071346] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 13.079732] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.391552] device br0 entered promiscuous mode
[ 15.427879] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[ 15.439704] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.450427] dwmac1000: Master AXI performs any burst length
[ 15.450455] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 15.464922] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 15.465040] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 15.472839] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 15.479739] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.488425] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.502962] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[ 15.511075] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.521790] dwmac1000: Master AXI performs any burst length
[ 15.521817] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 15.536173] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 15.536285] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 15.544099] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 15.551041] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.559569] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.570843] br0: port 1(eth0) entered blocking state
[ 15.574400] br0: port 1(eth0) entered disabled state
[ 15.579758] device eth0 entered promiscuous mode
[ 15.584690] br0: port 1(eth0) entered blocking state
[ 15.589157] br0: port 1(eth0) entered forwarding state
[ 15.594219] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[ 15.610473] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 15.625286] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.636014] dwmac1000: Master AXI performs any burst length
[ 15.636043] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 15.650398] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 15.650512] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 15.658306] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 15.665383] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.673967] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.688234] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 15.696557] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.707278] dwmac1000: Master AXI performs any burst length
[ 15.707307] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 15.721732] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 15.721845] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 15.729584] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 15.736598] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.745196] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.755712] br0: port 2(eth1) entered blocking state
[ 15.759961] br0: port 2(eth1) entered disabled state
[ 15.765405] device eth1 entered promiscuous mode
[ 15.770144] br0: port 2(eth1) entered blocking state
[ 15.774796] br0: port 2(eth1) entered forwarding state
[ 15.791892] device br0 left promiscuous mode
[ 15.794848] device br0 entered promiscuous mode
[ 15.803044] device br0 left promiscuous mode
[ 15.909334] ath: EEPROM regdomain: 0x8348
[ 15.909349] ath: EEPROM indicates we should expect a country code
[ 15.909355] ath: doing EEPROM country->regdmn map search
[ 15.909360] ath: country maps to regdmn code: 0x3a
[ 15.909364] ath: Country alpha2 being used: US
[ 15.909369] ath: Regpair used: 0x3a
[ 15.909374] ath: regdomain 0x8348 dynamically updated by user
[ 15.909430] ath: EEPROM regdomain: 0x8348
[ 15.909437] ath: EEPROM indicates we should expect a country code
[ 15.909443] ath: doing EEPROM country->regdmn map search
[ 15.909448] ath: country maps to regdmn code: 0x3a
[ 15.909455] ath: Country alpha2 being used: US
[ 15.909459] ath: Regpair used: 0x3a
[ 15.909464] ath: regdomain 0x8348 dynamically updated by user
[ 15.956098] ath: EEPROM regdomain: 0x8348
[ 15.956112] ath: EEPROM indicates we should expect a country code
[ 15.956118] ath: doing EEPROM country->regdmn map search
[ 15.956123] ath: country maps to regdmn code: 0x3a
[ 15.956128] ath: Country alpha2 being used: US
[ 15.956133] ath: Regpair used: 0x3a
[ 15.956137] ath: regdomain 0x8348 dynamically updated by user
[ 15.956187] ath: EEPROM regdomain: 0x8348
[ 15.956192] ath: EEPROM indicates we should expect a country code
[ 15.956197] ath: doing EEPROM country->regdmn map search
[ 15.956201] ath: country maps to regdmn code: 0x3a
[ 15.956206] ath: Country alpha2 being used: US
[ 15.956210] ath: Regpair used: 0x3a
[ 15.956215] ath: regdomain 0x8348 dynamically updated by user
[ 16.659395] tun: Universal TUN/TAP device driver, 1.6
[ 20.664512] usbcore: registered new interface driver usbfs
[ 20.664588] usbcore: registered new interface driver hub
[ 20.668952] usbcore: registered new device driver usb
[ 21.481336] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 21.481385] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 21.486091] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 21.493401] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x10000000
[ 21.502864] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 21.508556] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 21.514182] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 21.522164] hub 1-0:1.0: USB hub found
[ 21.528290] hub 1-0:1.0: 1 port detected
[ 21.532383] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 21.536459] hub 2-0:1.0: USB hub found
[ 21.546652] hub 2-0:1.0: 1 port detected
[ 21.671337] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 21.671380] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 21.676094] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 21.683383] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x11000000
[ 21.692882] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 21.698563] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 21.704188] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 21.712696] hub 3-0:1.0: USB hub found
[ 21.718290] hub 3-0:1.0: 1 port detected
[ 21.722532] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 21.728888] hub 4-0:1.0: USB hub found
[ 21.734268] hub 4-0:1.0: 1 port detected
[ 21.861022] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 22.311272] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 23.291079] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 26.400721] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 26.400832] usb usb4: USB disconnect, device number 1
[ 26.404826] usb 4-1: USB disconnect, device number 2
[ 26.410967] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 26.414914] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 26.420541] usb usb3: USB disconnect, device number 1
[ 26.426982] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 26.430600] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 26.436342] usb usb2: USB disconnect, device number 1
[ 26.441986] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 26.446250] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 26.452049] usb usb1: USB disconnect, device number 1
[ 26.456916] usb 1-1: USB disconnect, device number 2
[ 26.463639] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 26.531802] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 26.531848] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 26.536556] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 26.543856] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x10000000
[ 26.553329] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 26.559017] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 26.564626] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 26.572630] hub 1-0:1.0: USB hub found
[ 26.578754] hub 1-0:1.0: 1 port detected
[ 26.582838] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 26.586950] hub 2-0:1.0: USB hub found
[ 26.594723] hub 2-0:1.0: 1 port detected
[ 26.598530] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 26.602325] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 26.607915] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 26.615209] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x11000000
[ 26.624668] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 26.630373] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 26.635983] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 26.644018] hub 3-0:1.0: USB hub found
[ 26.650108] hub 3-0:1.0: 1 port detected
[ 26.654188] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 26.658304] hub 4-0:1.0: USB hub found
[ 26.666064] hub 4-0:1.0: 1 port detected
[ 26.726862] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 26.825638] SCSI subsystem initialized
[ 26.901006] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 27.041102] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 27.252142] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 27.252570] scsi host0: usb-storage 1-1:1.0
[ 27.257462] usb-storage 4-1:1.0: USB Mass Storage device detected
[ 27.261600] scsi host1: usb-storage 4-1:1.0
[ 27.267658] usbcore: registered new interface driver usb-storage
[ 27.325748] libata version 3.00 loaded.
[ 27.489184] ahci 29000000.sata: supply ahci not found, using dummy regulator
[ 27.489340] ahci 29000000.sata: supply phy not found, using dummy regulator
[ 27.495484] ahci 29000000.sata: supply target not found, using dummy regulator
[ 27.502484] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[ 27.509298] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 27.514838] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 27.524590] scsi host2: ahci
[ 27.531829] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 50
[ 27.864651] ata1: SATA link down (SStatus 0 SControl 300)
[ 28.094242] sdhci: Secure Digital Host Controller Interface driver
[ 28.094277] sdhci: Copyright(c) Pierre Ossman
[ 28.145436] sdhci-pltfm: SDHCI platform and OF driver helper
[ 28.332266] scsi 0:0:0:0: Direct-Access USB Flash Drive 1.00 PQ: 0 ANSI: 6
[ 28.333781] sd 0:0:0:0: [sda] 30629376 512-byte logical blocks: (15.7 GB/14.6 GiB)
[ 28.341812] sd 0:0:0:0: [sda] Write Protect is off
[ 28.346838] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 28.347460] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 28.359658] sda: sda1
[ 28.361253] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 28.463572] ksmbd: kill command received
[ 28.525536] scsi 1:0:0:0: Direct-Access Samsung Flash Drive 1100 PQ: 0 ANSI: 6
[ 28.550650] sd 1:0:0:0: [sdb] 62656641 512-byte logical blocks: (32.1 GB/29.9 GiB)
[ 28.557667] sd 1:0:0:0: [sdb] Write Protect is off
[ 28.557700] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 28.569381] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.856702] br1: port 1(eth1.15) entered blocking state
[ 28.856741] br1: port 1(eth1.15) entered disabled state
[ 28.861049] device eth1.15 entered promiscuous mode
[ 28.869012] br1: port 1(eth1.15) entered blocking state
[ 30.176086] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 30.466205] EXT4-fs: Ignoring removed nobh option
[ 30.470974] EXT4-fs (sda1): barriers disabled
[ 30.489388] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none.
[ 30.533478] ksmbd: kill command received
[ 48.027387] br1: port 1(eth1.15) entered learning state
[ 63.027856] br1: port 1(eth1.15) entered forwarding state
[ 550.231925] I/O error, dev mtdblock9, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[ 550.233019] I/O error, dev mtdblock9, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[ 550.240836] I/O error, dev mtdblock9, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[ 550.250162] I/O error, dev mtdblock9, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[ 550.258811] I/O error, dev mtdblock9, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 550.266771] Buffer I/O error on dev mtdblock9, logical block 0, async page read
root@EA8500:~# uptime && date
21:40:41 up 9 min, load average: 0.05, 0.04, 0.02
Mon Oct 23 21:40:41 CDT 2023
root@EA8500:~# ubootenv set boot_part 2 && reboot
a_pEnv->crc = cd7de424
crc32 = cd7de424
root@EA8500:~# Connection to ea8500.mrjcd.com closed by remote host.
Connection to ea8500.mrjcd.com closed.
mrjcd@daDeb:~$