mrjcd@daDeb:~$ ssh root@ea8500.mrjcd.com
DD-WRT v3.0-r53717 std (c) 2023 NewMedia-NET GmbH
Release: 10/20/23
Board: Linksys EA8500
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
https://www.dd-wrt.com
==========================================================
BusyBox v1.36.1 (2023-10-20 13:07:52 +07) built-in shell (ash)
root@EA8500:~# df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 22016 22016 0 100% /
none 512 0 512 0% /dev
/dev/sda1 14965728 6018792 8164908 42% /tmp/mnt/sda1
root@EA8500:~# blkid
/dev/sda1: LABEL="16GBext4" UUID="0cfdee24-2710-4fff-a543-0f8afb91a82f"
root@EA8500:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 6.1.59 (root@server2) (arm-openwrt-linux-gcc (OpenWrt GCC 13.2.0 r24111-66f6c20e45) 13.2.0, GNU ld (GNU Binutils) 2.41) #3 SMP Fri Oct 20 13:06:02 +07 2023
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys EA8500 WiFi Router
[ 0.000000] OF: fdt: Ignoring memory range 0x41500000 - 0x42000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s15444 r8192 d21420 u45056
[ 0.000000] pcpu-alloc: s15444 r8192 d21420 u45056 alloc=11*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 474732K/491520K available (7897K kernel code, 671K rwdata, 2180K rodata, 1024K init, 374K bss, 16788K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000001] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000021] Switching to timer-based delay loop, resolution 160ns
[ 0.000256] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000282] CPU: Testing write buffer coherency: ok
[ 0.000336] pid_max: default: 32768 minimum: 301
[ 0.000913] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000934] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.002414] qcom_scm: convention: smc legacy
[ 0.003220] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.003376] rcu: Hierarchical SRCU implementation.
[ 0.003387] rcu: Max phase no-delay instances is 1000.
[ 0.003902] smp: Bringing up secondary CPUs ...
[ 0.005777] smp: Brought up 1 node, 2 CPUs
[ 0.005794] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.005805] CPU: All CPU(s) started in SVC mode.
[ 0.016847] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.017007] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.017041] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.017198] pinctrl core: initialized pinctrl subsystem
[ 0.019229] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.019652] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.021237] thermal_sys: Registered thermal governor 'step_wise'
[ 0.021569] cpuidle: using governor ladder
[ 0.021631] cpuidle: using governor menu
[ 0.057783] cryptd: max_cpu_qlen set to 1000
[ 0.060455] pps_core: LinuxPPS API ver. 1 registered
[ 0.060464] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.060500] PTP clock support registered
[ 0.062361] mctp: management component transport protocol core
[ 0.062372] NET: Registered PF_MCTP protocol family
[ 0.062914] clocksource: Switched to clocksource dg_timer
[ 0.063420] VFS: Disk quotas dquot_6.6.0
[ 0.063543] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.064743] NET: Registered PF_INET protocol family
[ 0.064982] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.066394] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.066428] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.066452] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.066487] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.066568] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.066872] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.066980] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.067010] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.067307] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.067361] PCI: CLS 0 bytes, default 64
[ 0.070687] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.077602] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.189741] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[ 0.189963] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[ 0.190059] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.190322] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.190365] qcom-pcie 1b500000.pci: Parsing ranges property...
[ 0.190406] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fe0ffff -> 0x0000000000
[ 0.190444] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[ 0.316060] qcom-pcie 1b500000.pci: Using 32 MSI vectors
[ 0.316223] qcom-pcie 1b500000.pci: iATU unroll: disabled
[ 0.316239] qcom-pcie 1b500000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[ 0.419005] qcom-pcie 1b500000.pci: PCIe Gen.1 x1 link up
[ 0.419217] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.419234] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.419249] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.419264] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.419278] pci_bus 0000:00: scanning bus
[ 0.419331] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.419474] pci 0000:00:00.0: supports D1
[ 0.419487] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.419503] pci 0000:00:00.0: PME# disabled
[ 0.422837] pci_bus 0000:00: fixups for bus
[ 0.422863] PCI: bus0: Fast back to back transfers disabled
[ 0.422880] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.423019] pci_bus 0000:01: scanning bus
[ 0.423388] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.423681] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.425034] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.425090] pci 0000:01:00.0: PME# disabled
[ 0.425498] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 0.426287] pci_bus 0000:01: fixups for bus
[ 0.426373] PCI: bus1: Fast back to back transfers disabled
[ 0.426385] pci_bus 0000:01: bus scan returning with max=01
[ 0.426403] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.426423] pci_bus 0000:00: bus scan returning with max=ff
[ 0.426453] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.426477] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.426624] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.426645] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.426850] pcieport 0000:00:00.0: assign IRQ: got 27
[ 0.426992] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x43741000
[ 0.427656] pcieport 0000:00:00.0: AER: enabled with IRQ 28
[ 0.427788] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 0.427808] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 0.427823] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 0.427835] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 0.427847] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 0.427861] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 0.427873] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 0.427884] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 0.427897] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x8100800)
[ 0.427908] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 0.427920] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 0.427932] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 0.427944] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 0.427956] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 0.427968] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 0.427980] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3011b)
[ 0.428710] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[ 0.428974] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[ 0.429078] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.429414] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 0.429454] qcom-pcie 1b700000.pci: Parsing ranges property...
[ 0.429500] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031e0ffff -> 0x0000000000
[ 0.429536] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[ 0.545795] qcom-pcie 1b700000.pci: Using 32 MSI vectors
[ 0.545950] qcom-pcie 1b700000.pci: iATU unroll: disabled
[ 0.545962] qcom-pcie 1b700000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[ 0.648649] qcom-pcie 1b700000.pci: PCIe Gen.2 x1 link up
[ 0.648885] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.648901] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.648922] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
[ 0.648935] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.648947] pci_bus 0001:00: scanning bus
[ 0.648996] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.649132] pci 0001:00:00.0: supports D1
[ 0.649144] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.649159] pci 0001:00:00.0: PME# disabled
[ 0.652411] pci_bus 0001:00: fixups for bus
[ 0.652433] PCI: bus0: Fast back to back transfers disabled
[ 0.652447] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 0.652627] pci_bus 0001:01: scanning bus
[ 0.652868] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.653239] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.654493] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.654544] pci 0001:01:00.0: PME# disabled
[ 0.655611] pci_bus 0001:01: fixups for bus
[ 0.655689] PCI: bus1: Fast back to back transfers disabled
[ 0.655703] pci_bus 0001:01: bus scan returning with max=01
[ 0.655718] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 0.655738] pci_bus 0001:00: bus scan returning with max=ff
[ 0.655766] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.655789] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.655928] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.655950] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.656176] pcieport 0001:00:00.0: assign IRQ: got 30
[ 0.656320] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x43749000
[ 0.656782] pcieport 0001:00:00.0: AER: enabled with IRQ 31
[ 0.656935] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 0.656952] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 0.656964] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 0.656975] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 0.656987] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 0.657000] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 0.657011] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 0.657024] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 0.657035] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
[ 0.657046] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 0.657058] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 0.657070] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 0.657081] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 0.657094] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 0.657105] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 0.657116] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x3011e)
[ 0.661143] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[ 0.661170] krait-cc soc:clock-controller: CPU1 @ Undefined rate. Forcing new rate.
[ 0.661315] krait-cc soc:clock-controller: CPU1 @ 384000 KHz
[ 0.661331] krait-cc soc:clock-controller: L2 @ Undefined rate. Forcing new rate.
[ 0.661542] krait-cc soc:clock-controller: L2 @ 384000 KHz
[ 0.667215] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.669498] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.670876] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.670927] msm_serial 16340000.serial: uartclk = 7372800
[ 0.671097] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 35, base_baud = 460800) is a MSM
[ 0.671135] msm_serial: console setup on port #0
[ 1.564270] printk: console [ttyMSM0] enabled
[ 1.569534] msm_serial: driver initialized
[ 1.579613] loop: module loaded
[ 1.581419] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 1.581572] nand: AMD/Spansion S34MS01G2
[ 1.588254] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.983392] random: crng init done
[ 2.160325] found squashfs at 1380000 with len of 22413312 bytes
[ 2.586226] found squashfs at 3A80000 with len of 21757952 bytes
[ 2.586281] 19 fixed-partitions partitions found on MTD device qcom_nand.0
[ 2.591337] Creating 19 MTD partitions on "qcom_nand.0":
[ 2.598082] 0x000000000000-0x000000040000 : "SBL1"
[ 2.607080] 0x000000040000-0x000000180000 : "MIBIB"
[ 2.610647] 0x000000180000-0x0000002c0000 : "SBL2"
[ 2.615470] 0x0000002c0000-0x000000540000 : "SBL3"
[ 2.622402] 0x000000540000-0x000000660000 : "DDRCONFIG"
[ 2.624861] 0x000000660000-0x000000780000 : "SSD"
[ 2.629927] 0x000000780000-0x000000a00000 : "TZ"
[ 2.637299] 0x000000a00000-0x000000c80000 : "RPM"
[ 2.641946] 0x000000c80000-0x000000dc0000 : "art"
[ 2.644594] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[ 2.648630] 0x000000ec0000-0x000000f00000 : "u_env"
[ 2.652379] 0x000000f00000-0x000000f40000 : "s_env"
[ 2.657065] 0x000000f40000-0x000000f80000 : "devinfo"
[ 2.661836] 0x000000f80000-0x000003780000 : "linux"
[ 2.734020] 0x000001380000-0x0000028e0000 : "rootfs"
[ 2.770882] mtd: setting mtd14 (rootfs) as root device
[ 2.771464] 1 squashfs-split partitions found on MTD device rootfs
[ 2.774993] 0x0000028e0000-0x000008000000 : "rootfs_data"
[ 2.926952] 0x000003780000-0x000005f40000 : "linux2"
[ 2.993774] 0x000003a80000-0x000004f40000 : "rootfs2"
[ 3.029491] 0x000005f40000-0x000005f80000 : "nvram"
[ 3.030427] 0x000005f80000-0x000008000000 : "ddwrt"
[ 3.120550] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[ 3.939435] ar8327: qca,phy-rgmii-en is not specified
[ 3.940763] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[ 3.943580] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[ 3.950851] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 3.957681] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 3.963674] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 3.970996] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 3.976938] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 3.984639] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 3.992435] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 3.998322] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 4.005729] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 4.012402] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 4.020035] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 4.027065] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 4.033263] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address 66:1c:33:d6:59:6a
[ 4.047856] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[ 4.049564] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[ 4.057260] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 4.063802] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 4.069700] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 4.077283] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 4.082976] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 4.090792] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 4.098721] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 4.104508] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 4.111793] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 4.118658] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 4.126187] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 4.133252] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 4.139328] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address ce:9f:99:71:63:48
[ 4.153270] PPP generic driver version 2.4.2
[ 4.155915] PPP BSD Compression module registered
[ 4.160147] PPP Deflate Compression module registered
[ 4.165419] PPP MPPE Compression module registered
[ 4.169782] NET: Registered PF_PPPOX protocol family
[ 4.175023] i2c_dev: i2c /dev entries driver
[ 4.188149] GACT probability NOT on
[ 4.188223] Mirror/redirect action on
[ 4.190631] Simple TC action Loaded
[ 4.195509] netem: version 1.3
[ 4.197653] u32 classifier
[ 4.200703] Performance counters on
[ 4.203530] input device check on
[ 4.207127] Actions configured
[ 4.212120] nf_conntrack_rtsp v0.7 loading
[ 4.214958] xt_time: kernel timezone is -0000
[ 4.218823] gre: GRE over IPv4 demultiplexor driver
[ 4.223745] NET: Registered PF_INET6 protocol family
[ 4.230253] Segment Routing with IPv6
[ 4.232694] In-situ OAM (IOAM) with IPv6
[ 4.236593] NET: Registered PF_PACKET protocol family
[ 4.240336] Bridge firewalling registered
[ 4.245283] 8021q: 802.1Q VLAN Support v1.8
[ 4.249389] Registering SWP/SWPB emulation handler
[ 4.256541] registered taskstats version 1
[ 4.305720] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 4.318524] s1a: Bringing 0uV into 1050000-1050000uV
[ 4.318938] s1b: Bringing 0uV into 1050000-1050000uV
[ 4.322887] s2a: Bringing 0uV into 800000-800000uV
[ 4.327956] s2b: Bringing 0uV into 800000-800000uV
[ 4.343268] thermal thermal_zone0: failed to read out thermal zone (-110)
[ 4.357777] searching for nvram
[ 4.357818] nvram size = 262144
[ 4.410659] found nvram at 20000
[ 4.437321] UBI error: no valid UBI magic found inside mtd13
[ 4.446475] VFS: Mounted root (squashfs filesystem) readonly on device 31:14.
[ 4.447011] Freeing unused kernel image (initmem) memory: 1024K
[ 4.493553] Run /sbin/init as init process
[ 4.493571] with arguments:
[ 4.493575] /sbin/init
[ 4.493579] with environment:
[ 4.493583] HOME=/
[ 4.493588] TERM=linux
[ 8.001396] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace
[ 8.001430] Backport generated by backports.git v5.15.33-1-0-g183c4ab2
[ 8.389681] ath9k: ath9k: Driver unloaded
[ 8.689923] ath10k_pci 0000:01:00.0: assign IRQ: got 27
[ 8.690402] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 8.690501] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 8.691023] qcom-pcie 1b500000.pci: msi#1 address_hi 0x0 address_lo 0x43741000
[ 8.691196] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 9.012970] ath10k_pci 0000:01:00.0: found firmware features ie (8 B)
[ 9.013011] ath10k_pci 0000:01:00.0: Unknown FW IE: 30
[ 9.018462] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 9.023497] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[ 9.034364] ath10k_pci 0000:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7264 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 39c77aba
[ 9.099023] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[ 9.102318] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 9.108339] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 9.129878] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 e4a0f655
[ 9.151033] ath10k_pci 0000:01:00.0: boot already acquired valid otp board id,skip download, board_id 2 chip_id 1
[ 9.171636] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11240
[ 10.235334] ath10k_pci 0000:01:00.0: Init Max Stations to 64
[ 10.235922] ath10k_pci 0000:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000002 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 10.327296] ath10k_pci 0000:01:00.0: wmi debug print truncated: 128
[ 10.327323] ath10k_pci 0000:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 1 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0 c
[ 10.332418] ath10k_pci 0000:01:00.0: free: 18212 iram: 32064 sram: 17864
[ 10.344941] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[ 10.383806] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 10.467346] ath10k_pci 0000:01:00.0: init channel number 86
[ 10.467380] ath: EEPROM regdomain sanitized
[ 10.467386] ath: EEPROM regdomain: 0x64
[ 10.467391] ath: EEPROM indicates we should expect a direct regpair map
[ 10.467400] ath: Country alpha2 being used: 00
[ 10.467405] ath: Regpair used: 0x64
[ 10.467442] initialize fq_codel with 33554432 bytes memory limit
[ 10.471805] ieee80211_txq_setup_flows: set limit to 4194304 bytes
[ 10.481370] ath10k_pci 0001:01:00.0: assign IRQ: got 30
[ 10.481912] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 10.484097] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 10.484576] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x43749000
[ 10.484740] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 10.645132] ath10k_pci 0001:01:00.0: found firmware features ie (8 B)
[ 10.645167] ath10k_pci 0001:01:00.0: Unknown FW IE: 30
[ 10.650556] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 10.655652] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[ 10.666791] ath10k_pci 0001:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7264 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 39c77aba
[ 10.730990] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[ 10.734282] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 10.740228] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 10.749856] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 e4a0f655
[ 10.779002] ath10k_pci 0001:01:00.0: boot already acquired valid otp board id,skip download, board_id 1 chip_id 1
[ 10.799440] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11240
[ 11.859817] ath10k_pci 0001:01:00.0: Init Max Stations to 64
[ 11.860409] ath10k_pci 0001:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000001 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 11.949620] ath10k_pci 0001:01:00.0: wmi debug print truncated: 128
[ 11.949645] ath10k_pci 0001:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 2 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0 c
[ 11.954812] ath10k_pci 0001:01:00.0: free: 18212 iram: 32064 sram: 17864
[ 11.967235] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[ 12.004272] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 12.087361] ath10k_pci 0001:01:00.0: init channel number 134
[ 12.087395] ath: EEPROM regdomain sanitized
[ 12.087400] ath: EEPROM regdomain: 0x64
[ 12.087407] ath: EEPROM indicates we should expect a direct regpair map
[ 12.087416] ath: Country alpha2 being used: 00
[ 12.087420] ath: Regpair used: 0x64
[ 12.087460] initialize fq_codel with 33554432 bytes memory limit
[ 12.092166] ieee80211_txq_setup_flows: set limit to 33554432 bytes
[ 13.049391] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 13.060132] dwmac1000: Master AXI performs any burst length
[ 13.060159] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 13.074577] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 13.074714] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 13.083817] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 13.089527] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 13.098083] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 13.109494] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 13.123602] dwmac1000: Master AXI performs any burst length
[ 13.123629] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 13.137983] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 13.138103] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 13.146399] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 13.153098] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 13.161376] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.494244] device br0 entered promiscuous mode
[ 15.530544] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[ 15.542485] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.553292] dwmac1000: Master AXI performs any burst length
[ 15.553320] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 15.567676] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 15.567792] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 15.575596] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 15.582542] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.591161] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.605793] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[ 15.613983] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.624714] dwmac1000: Master AXI performs any burst length
[ 15.624741] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 15.639096] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 15.639214] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 15.647028] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 15.653980] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.662491] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.673832] br0: port 1(eth0) entered blocking state
[ 15.682532] br0: port 1(eth0) entered disabled state
[ 15.688000] device eth0 entered promiscuous mode
[ 15.692765] br0: port 1(eth0) entered blocking state
[ 15.697351] br0: port 1(eth0) entered forwarding state
[ 15.702294] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[ 15.713485] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 15.728391] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.739140] dwmac1000: Master AXI performs any burst length
[ 15.739170] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 15.753608] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 15.753725] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 15.761458] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 15.768550] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.777125] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.791566] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 15.800006] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 15.810749] dwmac1000: Master AXI performs any burst length
[ 15.810777] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 15.825217] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 15.825332] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 15.833065] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 15.840097] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.848694] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.859192] br0: port 2(eth1) entered blocking state
[ 15.863546] br0: port 2(eth1) entered disabled state
[ 15.868811] device eth1 entered promiscuous mode
[ 15.873705] br0: port 2(eth1) entered blocking state
[ 15.878204] br0: port 2(eth1) entered forwarding state
[ 15.895399] device br0 left promiscuous mode
[ 15.898348] device br0 entered promiscuous mode
[ 15.906375] device br0 left promiscuous mode
[ 16.014399] ath: EEPROM regdomain: 0x8348
[ 16.014414] ath: EEPROM indicates we should expect a country code
[ 16.014421] ath: doing EEPROM country->regdmn map search
[ 16.014426] ath: country maps to regdmn code: 0x3a
[ 16.014431] ath: Country alpha2 being used: US
[ 16.014436] ath: Regpair used: 0x3a
[ 16.014442] ath: regdomain 0x8348 dynamically updated by user
[ 16.014501] ath: EEPROM regdomain: 0x8348
[ 16.014508] ath: EEPROM indicates we should expect a country code
[ 16.014513] ath: doing EEPROM country->regdmn map search
[ 16.014518] ath: country maps to regdmn code: 0x3a
[ 16.014523] ath: Country alpha2 being used: US
[ 16.014527] ath: Regpair used: 0x3a
[ 16.014532] ath: regdomain 0x8348 dynamically updated by user
[ 16.058223] ath: EEPROM regdomain: 0x8348
[ 16.058237] ath: EEPROM indicates we should expect a country code
[ 16.058243] ath: doing EEPROM country->regdmn map search
[ 16.058248] ath: country maps to regdmn code: 0x3a
[ 16.058254] ath: Country alpha2 being used: US
[ 16.058259] ath: Regpair used: 0x3a
[ 16.058264] ath: regdomain 0x8348 dynamically updated by user
[ 16.058316] ath: EEPROM regdomain: 0x8348
[ 16.058321] ath: EEPROM indicates we should expect a country code
[ 16.058326] ath: doing EEPROM country->regdmn map search
[ 16.058331] ath: country maps to regdmn code: 0x3a
[ 16.058335] ath: Country alpha2 being used: US
[ 16.058340] ath: Regpair used: 0x3a
[ 16.058344] ath: regdomain 0x8348 dynamically updated by user
[ 16.761893] tun: Universal TUN/TAP device driver, 1.6
[ 20.553601] usbcore: registered new interface driver usbfs
[ 20.553671] usbcore: registered new interface driver hub
[ 20.558045] usbcore: registered new device driver usb
[ 21.383689] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 21.383737] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 21.388473] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 21.395822] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x10000000
[ 21.405240] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 21.410909] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 21.416527] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 21.417285] hub 1-0:1.0: USB hub found
[ 21.435346] hub 1-0:1.0: 1 port detected
[ 21.438761] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 21.442965] hub 2-0:1.0: USB hub found
[ 21.451300] hub 2-0:1.0: 1 port detected
[ 21.583676] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 21.583720] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 21.588434] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 21.595720] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x11000000
[ 21.605211] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 21.610895] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 21.616523] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 21.625420] hub 3-0:1.0: USB hub found
[ 21.630617] hub 3-0:1.0: 1 port detected
[ 21.634735] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 21.639212] hub 4-0:1.0: USB hub found
[ 21.646967] hub 4-0:1.0: 1 port detected
[ 21.773347] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 22.243304] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 23.213687] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 26.312695] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 26.312733] usb usb4: USB disconnect, device number 1
[ 26.316804] usb 4-1: USB disconnect, device number 2
[ 26.322966] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 26.326900] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 26.332448] usb usb3: USB disconnect, device number 1
[ 26.338600] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 26.342507] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 26.348235] usb usb2: USB disconnect, device number 1
[ 26.353772] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 26.358152] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 26.363963] usb usb1: USB disconnect, device number 1
[ 26.368813] usb 1-1: USB disconnect, device number 2
[ 26.375522] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 26.435405] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 26.435452] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 26.440164] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 26.447457] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x10000000
[ 26.456948] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 26.462621] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 26.468250] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 26.476269] hub 1-0:1.0: USB hub found
[ 26.482354] hub 1-0:1.0: 1 port detected
[ 26.486475] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 26.490595] hub 2-0:1.0: USB hub found
[ 26.498307] hub 2-0:1.0: 1 port detected
[ 26.502140] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 26.505953] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 26.511524] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 26.518787] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x11000000
[ 26.528296] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 26.534050] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 26.539531] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 26.547625] hub 3-0:1.0: USB hub found
[ 26.553766] hub 3-0:1.0: 1 port detected
[ 26.557716] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 26.561922] hub 4-0:1.0: USB hub found
[ 26.569677] hub 4-0:1.0: 1 port detected
[ 26.634852] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 26.737333] SCSI subsystem initialized
[ 26.853393] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 26.943442] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 27.202244] usb-storage 4-1:1.0: USB Mass Storage device detected
[ 27.202598] scsi host0: usb-storage 4-1:1.0
[ 27.207649] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 27.211610] scsi host1: usb-storage 1-1:1.0
[ 27.217854] usbcore: registered new interface driver usb-storage
[ 27.275926] libata version 3.00 loaded.
[ 27.441658] ahci 29000000.sata: supply ahci not found, using dummy regulator
[ 27.441819] ahci 29000000.sata: supply phy not found, using dummy regulator
[ 27.447986] ahci 29000000.sata: supply target not found, using dummy regulator
[ 27.454961] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[ 27.461768] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 27.467277] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 27.477219] scsi host2: ahci
[ 27.484306] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 50
[ 27.816884] ata1: SATA link down (SStatus 0 SControl 300)
[ 28.057813] sdhci: Secure Digital Host Controller Interface driver
[ 28.057847] sdhci: Copyright(c) Pierre Ossman
[ 28.110294] sdhci-pltfm: SDHCI platform and OF driver helper
[ 28.237007] scsi 1:0:0:0: Direct-Access USB Flash Drive 1.00 PQ: 0 ANSI: 6
[ 28.238679] sd 1:0:0:0: [sda] 30629376 512-byte logical blocks: (15.7 GB/14.6 GiB)
[ 28.245848] sd 1:0:0:0: [sda] Write Protect is off
[ 28.251652] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 28.252507] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 28.262478] sda: sda1
[ 28.271364] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 28.446586] ksmbd: kill command received
[ 28.480538] scsi 0:0:0:0: Direct-Access Samsung Flash Drive 1100 PQ: 0 ANSI: 6
[ 28.510013] sd 0:0:0:0: [sdb] 62656641 512-byte logical blocks: (32.1 GB/29.9 GiB)
[ 28.530435] sd 0:0:0:0: [sdb] Write Protect is off
[ 28.530469] sd 0:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 28.560574] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.836425] sd 0:0:0:0: [sdb] Attached SCSI removable disk
[ 28.856841] br1: port 1(eth1.15) entered blocking state
[ 28.856878] br1: port 1(eth1.15) entered disabled state
[ 28.861145] device eth1.15 entered promiscuous mode
[ 28.877130] br1: port 1(eth1.15) entered blocking state
[ 29.493148] EXT4-fs: Ignoring removed nobh option
[ 29.498135] EXT4-fs (sda1): barriers disabled
[ 29.959119] EXT4-fs (sda1): recovery complete
[ 29.972179] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none.
[ 48.109115] br1: port 1(eth1.15) entered learning state
[ 63.108939] br1: port 1(eth1.15) entered forwarding state
[ 65.113319] xhci-hcd xhci-hcd.1.auto: xHCI host not responding to stop endpoint command
[ 65.145368] xhci-hcd xhci-hcd.1.auto: Host halt failed, -110
[ 65.145399] xhci-hcd xhci-hcd.1.auto: xHCI host controller not responding, assume dead
[ 65.150115] xhci-hcd xhci-hcd.1.auto: HC died; cleaning up
[ 65.157972] sd 0:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x03 driverbyte=DRIVER_OK cmd_age=35s
[ 65.158536] usb 4-1: USB disconnect, device number 2
[ 65.163374] sd 0:0:0:0: [sdb] tag#0 CDB: opcode=0x28 28 00 00 02 00 e8 00 01 00 00
[ 65.178142] I/O error, dev sdb, sector 131304 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 2
[ 65.346352] ksmbd: kill command received
[ 65.545083] service (2935): drop_caches: 3
[ 245.474321] I/O error, dev mtdblock9, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[ 245.475449] I/O error, dev mtdblock9, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[ 245.483301] I/O error, dev mtdblock9, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[ 245.492376] I/O error, dev mtdblock9, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[ 245.501245] I/O error, dev mtdblock9, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 245.509166] Buffer I/O error on dev mtdblock9, logical block 0, async page read
root@EA8500:~# uptime && date
13:04:21 up 5 min, load average: 0.05, 0.21, 0.11
Fri Oct 20 13:04:21 CDT 2023
root@EA8500:~# ubootenv get boot_part
a_pEnv->crc = cd7de424
crc32 = cd7de424
1
root@EA8500:~# ubootenv set boot_part 2 && reboot
a_pEnv->crc = cd7de424
crc32 = cd7de424
root@EA8500:~# Connection to ea8500.mrjcd.com closed by remote host.
Connection to ea8500.mrjcd.com closed.
mrjcd@daDeb:~$ ssh root@ea8500.mrjcd.com
DD-WRT v3.0-r53562 std (c) 2023 NewMedia-NET GmbH
Release: 10/03/23
Board: Linksys EA8500
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
https://www.dd-wrt.com
==========================================================
BusyBox v1.36.1 (2023-10-03 02:16:29 +07) built-in shell (ash)
root@EA8500:~# df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 21248 21248 0 100% /
none 512 0 512 0% /dev
/dev/sda1 30657520 15815508 13259320 54% /tmp/mnt/sda1
/dev/sdb1 14965728 6018792 8164908 42% /tmp/mnt/sdb1
root@EA8500:~# blkid
/dev/sdb1: LABEL="16GBext4" UUID="0cfdee24-2710-4fff-a543-0f8afb91a82f"
/dev/sda1: LABEL="32GBext4" UUID="f704f783-cfb5-4547-9987-a7336cba923e"
root@EA8500:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.337 (root@server2) (gcc version 13.1.0 (OpenWrt GCC 13.1.0 r22658+9-2c530fcb97) ) #2196 SMP Tue Oct 3 02:15:11 +07 2023
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt:Machine model: Linksys EA8500 WiFi Router
[ 0.000000] OF: fdt:Ignoring memory range 0x41500000 - 0x42000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 122880
[ 0.000000] free_area_init_node: node 0, pgdat c0c2ea00, node_mem_map ddc39000
[ 0.000000] Normal zone: 960 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 122880 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 12 pages/cpu s19212 r8192 d21748 u49152
[ 0.000000] pcpu-alloc: s19212 r8192 d21748 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:16
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 477248K/491520K available (6144K kernel code, 190K rwdata, 1028K rodata, 1024K init, 363K bss, 14272K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc0900000 (7136 kB)
[ 0.000000] .init : 0xc0b00000 - 0xc0c00000 (1024 kB)
[ 0.000000] .data : 0xc0c00000 - 0xc0c2f850 ( 191 kB)
[ 0.000000] .bss : 0xc0c31000 - 0xc0c8bdf4 ( 364 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000007] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000020] Switching to timer-based delay loop, resolution 160ns
[ 0.000231] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000252] pid_max: default: 32768 minimum: 301
[ 0.000362] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000376] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000949] CPU: Testing write buffer coherency: ok
[ 0.001247] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001669] Setting up static identity map for 0x42300000 - 0x4230003c
[ 0.003968] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.004154] Brought up 2 CPUs
[ 0.004172] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.004183] CPU: All CPU(s) started in SVC mode.
[ 0.016289] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.016482] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.016509] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.016570] pinctrl core: initialized pinctrl subsystem
[ 0.018126] NET: Registered protocol family 16
[ 0.018470] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.041401] cpuidle: using governor ladder
[ 0.104652] msm_bus_fabric_init_driver
[ 0.105872] pps_core: LinuxPPS API ver. 1 registered
[ 0.105888] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.105921] PTP clock support registered
[ 0.108072] clocksource: Switched to clocksource dg_timer
[ 0.112049] NET: Registered protocol family 2
[ 0.112282] IP idents hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.113031] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.113069] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.113123] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.113176] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.113200] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.113368] NET: Registered protocol family 1
[ 0.113414] PCI: CLS 0 bytes, default 64
[ 0.117314] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.126653] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.132884] cryptodev: driver 1.9 loaded.
[ 0.132922] io scheduler noop registered
[ 0.132935] io scheduler deadline registered (default)
[ 0.134613] 1b500000.pci supply vdda not found, using dummy regulator
[ 0.134714] 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.134795] 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.135514] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[ 0.135556] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[ 0.135581] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000
[ 0.238454] qcom-pcie 1b500000.pci: link up
[ 0.238636] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.238659] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.238680] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.238695] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.238745] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.238894] pci 0000:00:00.0: supports D1
[ 0.238902] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.239196] PCI: bus0: Fast back to back transfers disabled
[ 0.239519] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.239766] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.240923] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.241320] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 0.241577] PCI: bus1: Fast back to back transfers disabled
[ 0.241864] pci 0000:00:00.0: BAR 14: assigned [mem 0x08000000-0x081fffff]
[ 0.241888] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.242021] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.242044] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.242459] aer 0000:00:00.0:pcie002: service driver aer loaded
[ 0.242909] 1b700000.pci supply vdda not found, using dummy regulator
[ 0.243015] 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.243097] 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.243817] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[ 0.243849] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000
[ 0.243871] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000
[ 0.348448] qcom-pcie 1b700000.pci: link up
[ 0.348628] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.348646] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.348661] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.348705] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.348825] pci 0001:00:00.0: supports D1
[ 0.348834] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.349092] PCI: bus0: Fast back to back transfers disabled
[ 0.349392] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.349615] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.350682] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.351282] PCI: bus1: Fast back to back transfers disabled
[ 0.351659] pci 0001:00:00.0: BAR 14: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.351681] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.351803] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.351821] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.352191] aer 0001:00:00.0:pcie002: service driver aer loaded
[ 0.352634] 1b900000.pci supply vdda not found, using dummy regulator
[ 0.352729] 1b900000.pci supply vdda_phy not found, using dummy regulator
[ 0.352811] 1b900000.pci supply vdda_refclk not found, using dummy regulator
[ 0.353532] OF: PCI: host bridge /soc/pci@1b900000 ranges:
[ 0.353570] OF: PCI: IO 0x35e00000..0x35efffff -> 0x35e00000
[ 0.353597] OF: PCI: MEM 0x32000000..0x35dfffff -> 0x32000000
[ 1.358438] qcom-pcie 1b900000.pci: phy link never came up
[ 1.360287] qcom-pcie 1b900000.pci: hostinit failed
[ 1.361005] deviceless supply s1b not found, using dummy regulator
[ 1.362561] L2 @ QSB rate. Forcing new rate.
[ 1.362725] L2 @ 800000 KHz
[ 1.362831] CPU0 @ 800000 KHz
[ 1.362842] CPU1 @ QSB rate. Forcing new rate.
[ 1.362958] CPU1 @ 800000 KHz
[ 1.364999] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 1.366644] serial8250_init
[ 1.366656] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.367622] msm_serial 16340000.serial: msm_serial: detected port #0
[ 1.367689] msm_serial 16340000.serial: uartclk = 7372800
[ 1.367746] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 201, base_baud = 460800) is a MSM
[ 1.367778] msm_serial: console setup on port #0
[ 2.128619] console [ttyMSM0] enabled
[ 2.133308] msm_serial: driver initialized
[ 2.138496] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 2.140708] nand: AMD/Spansion S34MS01G2
[ 2.147215] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.428473] random: crng init done
[ 2.752996] found squashfs at 1380000 with len of 22413312 bytes
[ 3.203677] found squashfs at 3A80000 with len of 21757952 bytes
[ 3.203715] 19 ofpart partitions found on MTD device qcom_nand.0
[ 3.208825] Creating 19 MTD partitions on "qcom_nand.0":
[ 3.214740] 0x000000000000-0x000000040000 : "SBL1"
[ 3.221348] 0x000000040000-0x000000180000 : "MIBIB"
[ 3.227213] 0x000000180000-0x0000002c0000 : "SBL2"
[ 3.232018] 0x0000002c0000-0x000000540000 : "SBL3"
[ 3.238416] 0x000000540000-0x000000660000 : "DDRCONFIG"
[ 3.241313] 0x000000660000-0x000000780000 : "SSD"
[ 3.246435] 0x000000780000-0x000000a00000 : "TZ"
[ 3.253474] 0x000000a00000-0x000000c80000 : "RPM"
[ 3.257831] 0x000000c80000-0x000000dc0000 : "art"
[ 3.260946] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[ 3.265094] 0x000000ec0000-0x000000f00000 : "u_env"
[ 3.269310] 0x000000f00000-0x000000f40000 : "s_env"
[ 3.273709] 0x000000f40000-0x000000f80000 : "devinfo"
[ 3.278741] 0x000000f80000-0x000003780000 : "linux"
[ 3.335895] 0x000001380000-0x0000028e0000 : "rootfs"
[ 3.364780] mtd: partition "rootfs" set to be root filesystem
[ 3.364813] 0x000003780000-0x000005f40000 : "linux2"
[ 3.422334] 0x000003a80000-0x000004f40000 : "rootfs2"
[ 3.450371] 0x000005f40000-0x000005f80000 : "nvram"
[ 3.451525] 0x000005f80000-0x000008000000 : "ddwrt"
[ 3.523176] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 4.343887] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 4.343913] Ring mode enabled
[ 4.347910] DMA HW capability register supported
[ 4.350937] Enhanced/Alternate descriptors
[ 4.356503] Enabled extended descriptors
[ 4.359517] RX Checksum Offload Engine supported
[ 4.363631] COE Type 2
[ 4.368313] TX Checksum insertion supported
[ 4.370637] Wake-Up On Lan supported
[ 4.375092] eth%d: device MAC address 00:06:3b:01:41:00
[ 4.378699] Enable RX Mitigation via HW Watchdog Timer
[ 4.384910] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 4.388980] Ring mode enabled
[ 4.394096] DMA HW capability register supported
[ 4.397050] Enhanced/Alternate descriptors
[ 4.402692] Enabled extended descriptors
[ 4.405651] RX Checksum Offload Engine supported
[ 4.409876] COE Type 2
[ 4.414502] TX Checksum insertion supported
[ 4.416762] Wake-Up On Lan supported
[ 4.421343] eth%d: device MAC address 00:03:7f:ba:db:02
[ 4.424838] Enable RX Mitigation via HW Watchdog Timer
[ 4.430736] i2c /dev entries driver
[ 4.435678] Calibration not found.
[ 4.439657] CPUidle arm: CPU 0 failed to init idle CPU ops
[ 4.442483] GACT probability NOT on
[ 4.447498] Mirror/redirect action on
[ 4.450989] Simple TC action Loaded
[ 4.455244] netem: version 1.3
[ 4.458019] u32 classifier
[ 4.461170] Performance counters on
[ 4.463808] input device check on
[ 4.467544] Actions configured
[ 4.471425] Netfilter messages via NETLINK v0.30.
[ 4.474920] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 4.480175] nf_conntrack_rtsp v0.7 loading
[ 4.485729] xt_time: kernel timezone is -0000
[ 4.489529] ip_set: protocol 6
[ 4.494032] gre: GRE over IPv4 demultiplexor driver
[ 4.497236] nf_nat_rtsp v0.7 loading
[ 4.501693] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.505580] NET: Registered protocol family 17
[ 4.510858] Bridge firewalling registered
[ 4.514942] 8021q: 802.1Q VLAN Support v1.8
[ 4.519219] Registering SWP/SWPB emulation handler
[ 4.523323] registered taskstats version 1
[ 4.536908] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 4.555351] s1a: Bringing 0uV into 1050000-1050000uV
[ 4.555627] s1b: Bringing 0uV into 1050000-1050000uV
[ 4.559672] s2a: Bringing 0uV into 800000-800000uV
[ 4.564531] s2b: Bringing 0uV into 800000-800000uV
[ 4.572709] trying to register driver cpufreq-dt
[ 4.575186] searching for nvram
[ 4.578588] nvram size = 262144
[ 4.664987] found nvram at 20000
[ 4.709528] no valid UBI magic found inside mtd13
[ 4.709580] hctosys: unable to open rtc device (rtc0)
[ 4.715152] rootfs2: allocate skip block area for 0x000000A6 blocks with 0x014C0000 bytes
[ 4.751757] VFS: Mounted root (squashfs filesystem) readonly on device 31:16.
[ 4.752501] Freeing unused kernel memory: 1024K
[ 7.928752] devinfo: allocate skip block area for 0x00000002 blocks with 0x00040000 bytes
[ 7.938420] art: allocate skip block area for 0x0000000A blocks with 0x00140000 bytes
[ 8.700353] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace
[ 8.700382] Backport generated by backports.git v5.15.33-1-0-g183c4ab2
[ 9.210205] ath9k: ath9k: Driver unloaded
[ 9.490679] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 9.491343] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 9.679822] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[ 9.969055] ath10k_pci 0000:01:00.0: found firmware features ie (8 B)
[ 9.969100] ath10k_pci 0000:01:00.0: Unknown FW IE: 30
[ 9.974492] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 9.979607] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[ 9.992314] ath10k_pci 0000:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7264 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 39c77aba
[ 10.055065] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[ 10.058361] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 10.064382] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[ 10.084140] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 e4a0f655
[ 10.105229] ath10k_pci 0000:01:00.0: boot already acquired valid otp board id,skip download, board_id 2 chip_id 1
[ 10.125829] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11240
[ 11.189049] ath10k_pci 0000:01:00.0: Init Max Stations to 64
[ 11.189731] ath10k_pci 0000:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000002 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 11.280722] ath10k_pci 0000:01:00.0: wmi debug print truncated: 128
[ 11.280747] ath10k_pci 0000:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 1 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0 c
[ 11.285999] ath10k_pci 0000:01:00.0: free: 18212 iram: 32064 sram: 17864
[ 11.298380] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[ 11.335800] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 11.446190] ath10k_pci 0000:01:00.0: init channel number 86
[ 11.446222] ath: EEPROM regdomain sanitized
[ 11.446228] ath: EEPROM regdomain: 0x64
[ 11.446234] ath: EEPROM indicates we should expect a direct regpair map
[ 11.446246] ath: Country alpha2 being used: 00
[ 11.446250] ath: Regpair used: 0x64
[ 11.446300] initialize fq_codel with 33554432 bytes memory limit
[ 11.450752] ieee80211_txq_setup_flows: set limit to 4194304 bytes
[ 11.463878] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 11.464618] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.629735] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[ 11.629797] ath10k_pci 0001:01:00.0: found firmware features ie (8 B)
[ 11.639442] ath10k_pci 0001:01:00.0: Unknown FW IE: 30
[ 11.645850] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 11.650958] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[ 11.663828] ath10k_pci 0001:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7264 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 39c77aba
[ 11.726249] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[ 11.729560] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 11.735497] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[ 11.745650] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 e4a0f655
[ 11.774417] ath10k_pci 0001:01:00.0: boot already acquired valid otp board id,skip download, board_id 1 chip_id 1
[ 11.794876] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11240
[ 12.854280] ath10k_pci 0001:01:00.0: Init Max Stations to 64
[ 12.854980] ath10k_pci 0001:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000001 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[ 12.943772] ath10k_pci 0001:01:00.0: wmi debug print truncated: 128
[ 12.943798] ath10k_pci 0001:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 2 P 80/80 V 16 K 160 PH 272 T 282 msdu-desc: 2500 sw-crypt: 0 c
[ 12.949120] ath10k_pci 0001:01:00.0: free: 18212 iram: 32064 sram: 17864
[ 12.961431] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[ 12.998160] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[ 13.101454] ath10k_pci 0001:01:00.0: init channel number 134
[ 13.101492] ath: EEPROM regdomain sanitized
[ 13.101500] ath: EEPROM regdomain: 0x64
[ 13.101507] ath: EEPROM indicates we should expect a direct regpair map
[ 13.101525] ath: Country alpha2 being used: 00
[ 13.101531] ath: Regpair used: 0x64
[ 13.101603] initialize fq_codel with 33554432 bytes memory limit
[ 13.106345] ieee80211_txq_setup_flows: set limit to 33554432 bytes
[ 14.228707] dwmac1000: Master AXI performs any burst length
[ 14.228769] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 14.233339] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 14.260272] dwmac1000: Master AXI performs any burst length
[ 14.260333] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 14.264884] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 15.288466] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.288509] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 16.426820] device br0 entered promiscuous mode
[ 16.486518] dwmac1000: Master AXI performs any burst length
[ 16.486557] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 16.491079] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 16.528034] dwmac1000: Master AXI performs any burst length
[ 16.528075] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 16.532596] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 16.543724] br0: port 1(eth0) entered blocking state
[ 16.548366] br0: port 1(eth0) entered disabled state
[ 16.553692] device eth0 entered promiscuous mode
[ 16.558580] br0: port 1(eth0) entered blocking state
[ 16.563047] br0: port 1(eth0) entered forwarding state
[ 16.602526] dwmac1000: Master AXI performs any burst length
[ 16.602565] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 16.607022] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 16.643799] dwmac1000: Master AXI performs any burst length
[ 16.643839] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 16.648288] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 16.659577] br0: port 2(eth1) entered blocking state
[ 16.664054] br0: port 2(eth1) entered disabled state
[ 16.669511] device eth1 entered promiscuous mode
[ 16.674237] br0: port 2(eth1) entered blocking state
[ 16.678885] br0: port 2(eth1) entered forwarding state
[ 16.689222] device br0 left promiscuous mode
[ 16.699984] device br0 entered promiscuous mode
[ 16.705727] device br0 left promiscuous mode
[ 16.808914] ath: EEPROM regdomain: 0x8348
[ 16.808919] ath: EEPROM indicates we should expect a country code
[ 16.808924] ath: doing EEPROM country->regdmn map search
[ 16.808928] ath: country maps to regdmn code: 0x3a
[ 16.808932] ath: Country alpha2 being used: US
[ 16.808934] ath: Regpair used: 0x3a
[ 16.808939] ath: regdomain 0x8348 dynamically updated by user
[ 16.809005] ath: EEPROM regdomain: 0x8348
[ 16.809008] ath: EEPROM indicates we should expect a country code
[ 16.809012] ath: doing EEPROM country->regdmn map search
[ 16.809015] ath: country maps to regdmn code: 0x3a
[ 16.809018] ath: Country alpha2 being used: US
[ 16.809020] ath: Regpair used: 0x3a
[ 16.809024] ath: regdomain 0x8348 dynamically updated by user
[ 16.846556] ath: EEPROM regdomain: 0x8348
[ 16.846561] ath: EEPROM indicates we should expect a country code
[ 16.846565] ath: doing EEPROM country->regdmn map search
[ 16.846569] ath: country maps to regdmn code: 0x3a
[ 16.846572] ath: Country alpha2 being used: US
[ 16.846575] ath: Regpair used: 0x3a
[ 16.846579] ath: regdomain 0x8348 dynamically updated by user
[ 16.846634] ath: EEPROM regdomain: 0x8348
[ 16.846636] ath: EEPROM indicates we should expect a country code
[ 16.846640] ath: doing EEPROM country->regdmn map search
[ 16.846643] ath: country maps to regdmn code: 0x3a
[ 16.846646] ath: Country alpha2 being used: US
[ 16.846649] ath: Regpair used: 0x3a
[ 16.846653] ath: regdomain 0x8348 dynamically updated by user
[ 17.393300] br0: port 1(eth0) entered disabled state
[ 17.427822] br0: port 2(eth1) entered disabled state
[ 17.459250] tun: Universal TUN/TAP device driver, 1.6
[ 17.459274] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 17.627458] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 17.637846] br0: port 1(eth0) entered blocking state
[ 17.637870] br0: port 1(eth0) entered forwarding state
[ 17.688489] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 17.688539] br0: port 2(eth1) entered blocking state
[ 17.696354] br0: port 2(eth1) entered forwarding state
[ 18.604328] Linux kernel CIFS/SMB SERVER 3.4.6 by Namjae Jeon <linkinjeon@kernel.org>
[ 18.676654] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 20.481797] usbcore: registered new interface driver usbfs
[ 20.481895] usbcore: registered new interface driver hub
[ 20.486214] usbcore: registered new device driver usb
[ 20.544463] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 20.554690] ehci-platform: EHCI generic platform driver
[ 20.581659] ehci-pci: EHCI PCI platform driver
[ 20.673026] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 21.050141] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 21.050229] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 21.054740] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010
[ 21.062209] xhci-hcd xhci-hcd.0.auto: irq 202, io mem 0x11000000
[ 21.063281] hub 1-0:1.0: USB hub found
[ 21.063739] hub 1-0:1.0: 1 port detected
[ 21.064025] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 21.064046] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 21.064572] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 21.065517] hub 2-0:1.0: USB hub found
[ 21.065984] hub 2-0:1.0: 1 port detected
[ 21.144298] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 21.144347] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 21.148898] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010
[ 21.156274] xhci-hcd xhci-hcd.1.auto: irq 203, io mem 0x10000000
[ 21.158459] hub 3-0:1.0: USB hub found
[ 21.158885] hub 3-0:1.0: 1 port detected
[ 21.159178] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 21.159198] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 21.159399] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 21.160001] hub 4-0:1.0: USB hub found
[ 21.160162] hub 4-0:1.0: 1 port detected
[ 21.438465] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 21.628254] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 22.568522] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 26.244145] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 26.244183] usb usb4: USB disconnect, device number 1
[ 26.249141] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 26.253679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 26.259034] usb usb3: USB disconnect, device number 1
[ 26.263881] usb 3-1: USB disconnect, device number 2
[ 26.269852] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 26.274015] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 26.279687] usb usb2: USB disconnect, device number 1
[ 26.284544] usb 2-1: USB disconnect, device number 2
[ 26.290511] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 26.294648] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 26.300366] usb usb1: USB disconnect, device number 1
[ 26.306390] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 26.356222] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 26.356307] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 26.360821] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010
[ 26.368169] xhci-hcd xhci-hcd.0.auto: irq 202, io mem 0x11000000
[ 26.377519] hub 1-0:1.0: USB hub found
[ 26.383216] hub 1-0:1.0: 1 port detected
[ 26.387006] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 26.390826] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 26.396111] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 26.404124] hub 2-0:1.0: USB hub found
[ 26.412026] hub 2-0:1.0: 1 port detected
[ 26.415910] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 26.419659] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 26.424988] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010
[ 26.432468] xhci-hcd xhci-hcd.1.auto: irq 203, io mem 0x10000000
[ 26.441818] hub 3-0:1.0: USB hub found
[ 26.447426] hub 3-0:1.0: 1 port detected
[ 26.451283] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 26.454974] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 26.460419] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 26.468396] hub 4-0:1.0: USB hub found
[ 26.476173] hub 4-0:1.0: 1 port detected
[ 26.526739] SCSI subsystem initialized
[ 26.628704] usbcore: registered new interface driver usb-storage
[ 26.686591] libata version 3.00 loaded.
[ 26.728273] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 26.731232] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[ 26.733713] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 26.739254] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 26.748484] scsi host0: ahci
[ 26.756186] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 95
[ 26.778319] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 26.800189] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 26.800409] scsi host1: usb-storage 2-1:1.0
[ 26.889639] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 26.891964] scsi host2: usb-storage 3-1:1.0
[ 27.089754] ata1: SATA link down (SStatus 0 SControl 300)
[ 27.265262] sdhci: Secure Digital Host Controller Interface driver
[ 27.265288] sdhci: Copyright(c) Pierre Ossman
[ 27.278257] sdhci-pltfm: SDHCI platform and OF driver helper
[ 27.694015] br1: port 1(eth1.15) entered blocking state
[ 27.694037] br1: port 1(eth1.15) entered disabled state
[ 27.698256] device eth1.15 entered promiscuous mode
[ 27.706163] br1: port 1(eth1.15) entered blocking state
[ 27.929321] scsi 2:0:0:0: Direct-Access USB Flash Drive 1.00 PQ: 0 ANSI: 6
[ 28.088511] scsi 1:0:0:0: Direct-Access Samsung Flash Drive 1100 PQ: 0 ANSI: 6
[ 28.090206] sd 2:0:0:0: [sdb] 30629376 512-byte logical blocks: (15.7 GB/14.6 GiB)
[ 28.091411] sd 1:0:0:0: [sda] 62656641 512-byte logical blocks: (32.1 GB/29.9 GiB)
[ 28.091569] sd 1:0:0:0: [sda] Write Protect is off
[ 28.091576] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 28.091731] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.095093] sda: sda1
[ 28.097697] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 28.128361] sd 2:0:0:0: [sdb] Write Protect is off
[ 28.132259] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 28.132953] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 28.145206] sdb: sdb1
[ 28.148652] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 28.250357] ksmbd: kill command received
[ 28.812692] EXT4-fs (sda1): Ignoring removed nobh option
[ 28.815063] EXT4-fs (sda1): barriers disabled
[ 28.829185] EXT4-fs (sda1): recovery complete
[ 28.829855] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: init_itable=0,nobarrier,nobh,barrier=0
[ 29.077556] EXT4-fs (sdb1): Ignoring removed nobh option
[ 29.100219] EXT4-fs (sdb1): barriers disabled
[ 29.130714] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: init_itable=0,nobarrier,nobh,barrier=0
[ 29.697267] Linux kernel CIFS/SMB SERVER 3.4.6 by Namjae Jeon <linkinjeon@kernel.org>
[ 47.578304] br1: port 1(eth1.15) entered learning state
[ 62.578573] br1: port 1(eth1.15) entered forwarding state
[ 107.856574] RPM: allocate skip block area for 0x00000014 blocks with 0x00280000 bytes
[ 107.862228] blk_update_request: I/O error, dev mtdblock7, sector 0
[ 107.864036] blk_update_request: I/O error, dev mtdblock7, sector 8
[ 107.870197] blk_update_request: I/O error, dev mtdblock7, sector 16
[ 107.876389] blk_update_request: I/O error, dev mtdblock7, sector 24
[ 107.882588] blk_update_request: I/O error, dev mtdblock7, sector 0
[ 107.888041] Buffer I/O error on dev mtdblock7, logical block 0, async page read
[ 107.894690] APPSBL: allocate skip block area for 0x00000008 blocks with 0x00100000 bytes
[ 107.904695] blk_update_request: I/O error, dev mtdblock9, sector 0
[ 107.910496] blk_update_request: I/O error, dev mtdblock9, sector 8
[ 107.916406] blk_update_request: I/O error, dev mtdblock9, sector 16
[ 107.922645] blk_update_request: I/O error, dev mtdblock9, sector 24
[ 107.928765] blk_update_request: I/O error, dev mtdblock9, sector 0
[ 107.934388] Buffer I/O error on dev mtdblock9, logical block 0, async page read
[ 107.940851] TZ: allocate skip block area for 0x00000014 blocks with 0x00280000 bytes
[ 107.955105] Buffer I/O error on dev mtdblock6, logical block 0, async page read
[ 107.956058] SSD: allocate skip block area for 0x00000009 blocks with 0x00120000 bytes
[ 107.976355] Buffer I/O error on dev mtdblock5, logical block 2, async page read
[ 107.977060] Buffer I/O error on dev mtdblock5, logical block 2, async page read
[ 107.983260] Buffer I/O error on dev mtdblock5, logical block 2, async page read
[ 107.990447] Buffer I/O error on dev mtdblock5, logical block 2, async page read
[ 107.997222] DDRCONFIG: allocate skip block area for 0x00000009 blocks with 0x00120000 bytes
[ 108.011280] Buffer I/O error on dev mtdblock4, logical block 0, async page read
[ 108.012936] SBL3: allocate skip block area for 0x00000014 blocks with 0x00280000 bytes
[ 108.027161] Buffer I/O error on dev mtdblock3, logical block 0, async page read
[ 108.028267] SBL2: allocate skip block area for 0x0000000A blocks with 0x00140000 bytes
[ 108.040928] Buffer I/O error on dev mtdblock2, logical block 0, async page read
[ 108.043292] ddwrt: allocate skip block area for 0x00000104 blocks with 0x02080000 bytes
[ 108.158182] nvram: allocate skip block area for 0x00000002 blocks with 0x00040000 bytes
[ 108.225863] linux2: allocate skip block area for 0x0000013E blocks with 0x027C0000 bytes
[ 108.333060] rootfs: allocate skip block area for 0x000000AB blocks with 0x01560000 bytes
[ 108.417672] linux: allocate skip block area for 0x00000140 blocks with 0x02800000 bytes
[ 108.580863] s_env: allocate skip block area for 0x00000002 blocks with 0x00040000 bytes
[ 108.640586] u_env: allocate skip block area for 0x00000002 blocks with 0x00040000 bytes
[ 108.701814] MIBIB: allocate skip block area for 0x0000000A blocks with 0x00140000 bytes
[ 108.707040] SBL1: allocate skip block area for 0x00000002 blocks with 0x00040000 bytes
root@EA8500:~# uptime && date
13:07:21 up 2 min, load average: 0.08, 0.08, 0.03
Fri Oct 20 13:07:21 CDT 2023
root@EA8500:~#
Connection to ea8500.mrjcd.com closed.
mrjcd@daDeb:~$