mrjcd@daDeb:~$ ssh root@ea8500.mrjcd.com
DD-WRT v3.0-r53714 std (c) 2023 NewMedia-NET GmbH
Release: 10/20/23
Board: Linksys EA8500
==========================================================
 
     ___  ___     _      _____  ______       ____  ___ 
    / _ \/ _ \___| | /| / / _ \/_  __/ _  __|_  / / _ \
   / // / // /___/ |/ |/ / , _/ / /   | |/ //_ <_/ // /
  /____/____/    |__/|__/_/|_| /_/    |___/____(_)___/ 
                                                     
                       DD-WRT v3.0
                   https://www.dd-wrt.com


==========================================================


BusyBox v1.36.1 (2023-10-20 03:10:11 +07) built-in shell (ash)

root@EA8500:~# df
Filesystem           1K-blocks      Used Available Use% Mounted on
/dev/root                22016     22016         0 100% /
none                       512         0       512   0% /dev
/dev/sda1             14965728   6014360   8169340  42% /tmp/mnt/sda1
root@EA8500:~# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 6.1.58 (root@server2) (arm-openwrt-linux-gcc (OpenWrt GCC 13.2.0 r24111-66f6c20e45) 13.2.0, GNU ld (GNU Binutils) 2.41) #169 SMP Fri Oct 20 03:08:16 +07 2023
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Linksys EA8500 WiFi Router
[    0.000000] OF: fdt: Ignoring memory range 0x41500000 - 0x42000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000] percpu: Embedded 11 pages/cpu s15444 r8192 d21420 u45056
[    0.000000] pcpu-alloc: s15444 r8192 d21420 u45056 alloc=11*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121920
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 474732K/491520K available (7897K kernel code, 671K rwdata, 2180K rodata, 1024K init, 374K bss, 16788K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000001] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000018] Switching to timer-based delay loop, resolution 160ns
[    0.000248] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000276] CPU: Testing write buffer coherency: ok
[    0.000328] pid_max: default: 32768 minimum: 301
[    0.000914] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000934] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.002438] qcom_scm: convention: smc legacy
[    0.003256] Setting up static identity map for 0x42300000 - 0x42300060
[    0.003417] rcu: Hierarchical SRCU implementation.
[    0.003426] rcu: 	Max phase no-delay instances is 1000.
[    0.003945] smp: Bringing up secondary CPUs ...
[    0.005834] smp: Brought up 1 node, 2 CPUs
[    0.005852] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.005866] CPU: All CPU(s) started in SVC mode.
[    0.016895] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.017058] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.017090] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.017254] pinctrl core: initialized pinctrl subsystem
[    0.019306] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.019715] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.021319] thermal_sys: Registered thermal governor 'step_wise'
[    0.021648] cpuidle: using governor ladder
[    0.021709] cpuidle: using governor menu
[    0.057849] cryptd: max_cpu_qlen set to 1000
[    0.060498] pps_core: LinuxPPS API ver. 1 registered
[    0.060510] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.060547] PTP clock support registered
[    0.062417] mctp: management component transport protocol core
[    0.062432] NET: Registered PF_MCTP protocol family
[    0.062955] clocksource: Switched to clocksource dg_timer
[    0.063464] VFS: Disk quotas dquot_6.6.0
[    0.063591] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.064783] NET: Registered PF_INET protocol family
[    0.065016] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.066417] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.066450] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.066474] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.066507] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.066586] TCP: Hash tables configured (established 4096 bind 4096)
[    0.066881] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.066991] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.067020] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.067319] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.067372] PCI: CLS 0 bytes, default 64
[    0.070744] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.077825] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.192231] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[    0.192459] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[    0.192551] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[    0.192805] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[    0.192846] qcom-pcie 1b500000.pci: Parsing ranges property...
[    0.192892] qcom-pcie 1b500000.pci:       IO 0x000fe00000..0x000fe0ffff -> 0x0000000000
[    0.192930] qcom-pcie 1b500000.pci:      MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[    0.316100] qcom-pcie 1b500000.pci: Using 32 MSI vectors
[    0.316256] qcom-pcie 1b500000.pci: iATU unroll: disabled
[    0.316270] qcom-pcie 1b500000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[    0.419068] qcom-pcie 1b500000.pci: PCIe Gen.1 x1 link up
[    0.419274] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.419291] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.419307] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.419321] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.419333] pci_bus 0000:00: scanning bus
[    0.419386] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.419529] pci 0000:00:00.0: supports D1
[    0.419542] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.419559] pci 0000:00:00.0: PME# disabled
[    0.422850] pci_bus 0000:00: fixups for bus
[    0.422875] PCI: bus0: Fast back to back transfers disabled
[    0.422890] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.423043] pci_bus 0000:01: scanning bus
[    0.423386] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[    0.423678] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.425032] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.425084] pci 0000:01:00.0: PME# disabled
[    0.425486] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    0.426284] pci_bus 0000:01: fixups for bus
[    0.426369] PCI: bus1: Fast back to back transfers disabled
[    0.426382] pci_bus 0000:01: bus scan returning with max=01
[    0.426401] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.426419] pci_bus 0000:00: bus scan returning with max=ff
[    0.426452] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.426475] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.426625] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    0.426647] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.426851] pcieport 0000:00:00.0: assign IRQ: got 27
[    0.426996] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x43741000
[    0.427666] pcieport 0000:00:00.0: AER: enabled with IRQ 28
[    0.427797] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[    0.427819] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[    0.427832] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[    0.427844] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
[    0.427856] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
[    0.427869] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
[    0.427880] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[    0.427894] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[    0.427905] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x8100800)
[    0.427917] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[    0.427930] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
[    0.427942] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
[    0.427953] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
[    0.427968] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
[    0.427979] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
[    0.427991] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3011b)
[    0.428729] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[    0.428994] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[    0.429091] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[    0.429414] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[    0.429455] qcom-pcie 1b700000.pci: Parsing ranges property...
[    0.429503] qcom-pcie 1b700000.pci:       IO 0x0031e00000..0x0031e0ffff -> 0x0000000000
[    0.429541] qcom-pcie 1b700000.pci:      MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[    0.545831] qcom-pcie 1b700000.pci: Using 32 MSI vectors
[    0.545985] qcom-pcie 1b700000.pci: iATU unroll: disabled
[    0.545998] qcom-pcie 1b700000.pci: iATU regions: 8 ob, 8 ib, align 4K, limit 4G
[    0.648681] qcom-pcie 1b700000.pci: PCIe Gen.2 x1 link up
[    0.648914] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.648932] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.648952] pci_bus 0001:00: root bus resource [io  0x10000-0x1ffff] (bus address [0x0000-0xffff])
[    0.648964] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.648978] pci_bus 0001:00: scanning bus
[    0.649027] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.649166] pci 0001:00:00.0: supports D1
[    0.649178] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[    0.649196] pci 0001:00:00.0: PME# disabled
[    0.652432] pci_bus 0001:00: fixups for bus
[    0.652454] PCI: bus0: Fast back to back transfers disabled
[    0.652469] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.652654] pci_bus 0001:01: scanning bus
[    0.652899] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[    0.653251] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.654510] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[    0.654560] pci 0001:01:00.0: PME# disabled
[    0.655626] pci_bus 0001:01: fixups for bus
[    0.655707] PCI: bus1: Fast back to back transfers disabled
[    0.655721] pci_bus 0001:01: bus scan returning with max=01
[    0.655738] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.655756] pci_bus 0001:00: bus scan returning with max=ff
[    0.655785] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.655808] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.655945] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    0.655969] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.656199] pcieport 0001:00:00.0: assign IRQ: got 30
[    0.656339] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x43749000
[    0.656800] pcieport 0001:00:00.0: AER: enabled with IRQ 31
[    0.656943] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[    0.656960] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[    0.656972] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[    0.656984] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
[    0.656997] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
[    0.657011] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
[    0.657023] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[    0.657036] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[    0.657047] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
[    0.657058] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[    0.657071] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
[    0.657083] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
[    0.657102] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
[    0.657115] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
[    0.657126] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
[    0.657138] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x3011e)
[    0.661120] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[    0.661146] krait-cc soc:clock-controller: CPU1 @ Undefined rate. Forcing new rate.
[    0.661291] krait-cc soc:clock-controller: CPU1 @ 384000 KHz
[    0.661306] krait-cc soc:clock-controller: L2 @ Undefined rate. Forcing new rate.
[    0.661511] krait-cc soc:clock-controller: L2 @ 384000 KHz
[    0.667190] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.669457] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.670817] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.670864] msm_serial 16340000.serial: uartclk = 7372800
[    0.671060] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 35, base_baud = 460800) is a MSM
[    0.671099] msm_serial: console setup on port #0
[    1.564553] printk: console [ttyMSM0] enabled
[    1.569800] msm_serial: driver initialized
[    1.579949] loop: module loaded
[    1.581722] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[    1.581910] nand: AMD/Spansion S34MS01G2
[    1.588599] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.983347] random: crng init done
[    2.156881] found squashfs at 1380000 with len of 22413312 bytes
[    2.579580] found squashfs at 3A80000 with len of 21757952 bytes
[    2.579633] 19 fixed-partitions partitions found on MTD device qcom_nand.0
[    2.584767] Creating 19 MTD partitions on "qcom_nand.0":
[    2.591348] 0x000000000000-0x000000040000 : "SBL1"
[    2.600413] 0x000000040000-0x000000180000 : "MIBIB"
[    2.604001] 0x000000180000-0x0000002c0000 : "SBL2"
[    2.608746] 0x0000002c0000-0x000000540000 : "SBL3"
[    2.615731] 0x000000540000-0x000000660000 : "DDRCONFIG"
[    2.618155] 0x000000660000-0x000000780000 : "SSD"
[    2.623334] 0x000000780000-0x000000a00000 : "TZ"
[    2.630499] 0x000000a00000-0x000000c80000 : "RPM"
[    2.635163] 0x000000c80000-0x000000dc0000 : "art"
[    2.637726] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[    2.641944] 0x000000ec0000-0x000000f00000 : "u_env"
[    2.645835] 0x000000f00000-0x000000f40000 : "s_env"
[    2.650334] 0x000000f40000-0x000000f80000 : "devinfo"
[    2.655265] 0x000000f80000-0x000003780000 : "linux"
[    2.726058] 0x000001380000-0x0000028e0000 : "rootfs"
[    2.762598] mtd: setting mtd14 (rootfs) as root device
[    2.763159] 1 squashfs-split partitions found on MTD device rootfs
[    2.766724] 0x0000028e0000-0x000008000000 : "rootfs_data"
[    2.915728] 0x000003780000-0x000005f40000 : "linux2"
[    2.981404] 0x000003a80000-0x000004f40000 : "rootfs2"
[    3.016666] 0x000005f40000-0x000005f80000 : "nvram"
[    3.017614] 0x000005f80000-0x000008000000 : "ddwrt"
[    3.106932] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[    3.909228] ar8327: qca,phy-rgmii-en is not specified
[    3.910531] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[    3.913368] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[    3.920660] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[    3.927515] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[    3.933463] ipq806x-gmac-dwmac 37200000.ethernet: 	DWMAC1000
[    3.940794] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[    3.946728] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[    3.954431] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[    3.962231] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[    3.968145] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[    3.975519] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[    3.982197] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[    3.989827] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[    3.996856] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    4.002962] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address ba:07:4c:6f:26:0f
[    4.017368] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[    4.019356] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[    4.027049] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[    4.033503] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[    4.039497] ipq806x-gmac-dwmac 37400000.ethernet: 	DWMAC1000
[    4.047088] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[    4.052773] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[    4.060631] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[    4.068488] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[    4.074300] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[    4.081588] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[    4.088450] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[    4.096010] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[    4.102942] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    4.109208] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address ba:f0:78:f8:01:c1
[    4.122909] PPP generic driver version 2.4.2
[    4.125809] PPP BSD Compression module registered
[    4.129943] PPP Deflate Compression module registered
[    4.135039] PPP MPPE Compression module registered
[    4.139579] NET: Registered PF_PPPOX protocol family
[    4.144818] i2c_dev: i2c /dev entries driver
[    4.158047] GACT probability NOT on
[    4.158121] Mirror/redirect action on
[    4.160512] Simple TC action Loaded
[    4.165407] netem: version 1.3
[    4.167552] u32 classifier
[    4.170599]     Performance counters on
[    4.173444]     input device check on
[    4.177023]     Actions configured
[    4.182041] nf_conntrack_rtsp v0.7 loading
[    4.184836] xt_time: kernel timezone is -0000
[    4.188728] gre: GRE over IPv4 demultiplexor driver
[    4.193644] NET: Registered PF_INET6 protocol family
[    4.200173] Segment Routing with IPv6
[    4.202592] In-situ OAM (IOAM) with IPv6
[    4.206485] NET: Registered PF_PACKET protocol family
[    4.210238] Bridge firewalling registered
[    4.215127] 8021q: 802.1Q VLAN Support v1.8
[    4.219263] Registering SWP/SWPB emulation handler
[    4.226355] registered taskstats version 1
[    4.276077] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[    4.288804] s1a: Bringing 0uV into 1050000-1050000uV
[    4.289207] s1b: Bringing 0uV into 1050000-1050000uV
[    4.293185] s2a: Bringing 0uV into 800000-800000uV
[    4.298236] s2b: Bringing 0uV into 800000-800000uV
[    4.313309] thermal thermal_zone0: failed to read out thermal zone (-110)
[    4.328305] searching for nvram
[    4.328347] nvram size = 262144
[    4.380774] found nvram at 20000
[    4.407238] UBI error: no valid UBI magic found inside mtd13
[    4.416287] VFS: Mounted root (squashfs filesystem) readonly on device 31:14.
[    4.416821] Freeing unused kernel image (initmem) memory: 1024K
[    4.463592] Run /sbin/init as init process
[    4.463612]   with arguments:
[    4.463616]     /sbin/init
[    4.463621]   with environment:
[    4.463626]     HOME=/
[    4.463631]     TERM=linux
[    7.988727] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace
[    7.988761] Backport generated by backports.git v5.15.33-1-0-g183c4ab2
[    8.376636] ath9k: ath9k: Driver unloaded
[    8.669750] ath10k_pci 0000:01:00.0: assign IRQ: got 27
[    8.670226] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[    8.670323] ath10k_pci 0000:01:00.0: enabling bus mastering
[    8.670845] qcom-pcie 1b500000.pci: msi#1 address_hi 0x0 address_lo 0x43741000
[    8.671019] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    8.991778] ath10k_pci 0000:01:00.0: found firmware features ie (8 B)
[    8.991819] ath10k_pci 0000:01:00.0: Unknown FW IE: 30
[    8.997281] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[    9.002242] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[    9.013211] ath10k_pci 0000:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7264 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 39c77aba
[    9.077796] ath10k_pci 0000:01:00.0: boot get otp board id result 0x00008800 board_id 2 chip_id 1 ext_bid_support 0
[    9.081093] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[    9.087096] ath10k_pci 0000:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=2'
[    9.107795] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 e4a0f655
[    9.128910] ath10k_pci 0000:01:00.0: boot already acquired valid otp board id,skip download, board_id 2 chip_id 1
[    9.149461] ath10k_pci 0000:01:00.0: boot upload otp to 0x1234 len 11240
[   10.212463] ath10k_pci 0000:01:00.0: Init Max Stations to 64
[   10.213160] ath10k_pci 0000:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000002 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[   10.304025] ath10k_pci 0000:01:00.0: wmi debug print truncated: 128
[   10.304052] ath10k_pci 0000:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 1 P 80/80 V 16 K 160 PH 272 T 282  msdu-desc: 2500  sw-crypt: 0 c
[   10.309152] ath10k_pci 0000:01:00.0: free: 18212 iram: 32064 sram: 17864
[   10.321668] ath10k_pci 0000:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[   10.360592] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[   10.447356] ath10k_pci 0000:01:00.0: init channel number 86
[   10.447393] ath: EEPROM regdomain sanitized
[   10.447398] ath: EEPROM regdomain: 0x64
[   10.447404] ath: EEPROM indicates we should expect a direct regpair map
[   10.447414] ath: Country alpha2 being used: 00
[   10.447420] ath: Regpair used: 0x64
[   10.447457] initialize fq_codel with 33554432 bytes memory limit
[   10.451815] ieee80211_txq_setup_flows: set limit to 4194304 bytes
[   10.461384] ath10k_pci 0001:01:00.0: assign IRQ: got 30
[   10.461913] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   10.464134] ath10k_pci 0001:01:00.0: enabling bus mastering
[   10.464630] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x43749000
[   10.464794] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   10.635206] ath10k_pci 0001:01:00.0: found firmware features ie (8 B)
[   10.635243] ath10k_pci 0001:01:00.0: Unknown FW IE: 30
[   10.640630] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[   10.645721] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[   10.656892] ath10k_pci 0001:01:00.0: firmware ver 10.4-ddwrt-9980-tW-13-7264 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 39c77aba
[   10.720994] ath10k_pci 0001:01:00.0: boot get otp board id result 0x00008400 board_id 1 chip_id 1 ext_bid_support 0
[   10.724286] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[   10.730235] ath10k_pci 0001:01:00.0: boot using board name 'bus=pci,bmi-chip-id=1,bmi-board-id=1'
[   10.739857] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 e4a0f655
[   10.769060] ath10k_pci 0001:01:00.0: boot already acquired valid otp board id,skip download, board_id 1 chip_id 1
[   10.789536] ath10k_pci 0001:01:00.0: boot upload otp to 0x1234 len 11240
[   11.849813] ath10k_pci 0001:01:00.0: Init Max Stations to 64
[   11.850412] ath10k_pci 0001:01:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000185b vht_cap 0x339b79b2 vht_supp_mcs 0x0000ffaa sw_ver0 0x01000000 sw_ver1 0x00000032 fw_build 0x00000000 phy_capab 0x00000001 num_rf_chains 0x00000004 eeprom_rd 0x00000000 low_2ghz_chan 2312 high_2ghz_chan 2732 low_5ghz_chan 4912 high_5ghz_chan 6100 num_mem_reqs 0x00000007 min_pkt_size_enable 0x00000000
[   11.939529] ath10k_pci 0001:01:00.0: wmi debug print truncated: 128
[   11.939555] ath10k_pci 0001:01:00.0: ChipType 1200 ChipTypeID 0 BoardID 2 P 80/80 V 16 K 160 PH 272 T 282  msdu-desc: 2500  sw-crypt: 0 c
[   11.944718] ath10k_pci 0001:01:00.0: free: 18212 iram: 32064 sram: 17864
[   11.957144] ath10k_pci 0001:01:00.0: wmi event ready sw_version 0x01000000 abi_version 3 mac_addr c0:56:27:08:b2:92 status 0
[   11.994207] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 64 raw 0 hwcrypto 1
[   12.077389] ath10k_pci 0001:01:00.0: init channel number 134
[   12.077424] ath: EEPROM regdomain sanitized
[   12.077429] ath: EEPROM regdomain: 0x64
[   12.077436] ath: EEPROM indicates we should expect a direct regpair map
[   12.077445] ath: Country alpha2 being used: 00
[   12.077450] ath: Regpair used: 0x64
[   12.077490] initialize fq_codel with 33554432 bytes memory limit
[   12.082195] ieee80211_txq_setup_flows: set limit to 33554432 bytes
[   13.039518] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   13.050248] dwmac1000: Master AXI performs any burst length
[   13.050276] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[   13.064708] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   13.064834] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   13.073979] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[   13.079669] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   13.088176] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   13.099584] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[   13.113728] dwmac1000: Master AXI performs any burst length
[   13.113755] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[   13.128111] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   13.128229] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   13.136468] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[   13.143044] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   13.152961] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   15.464269] device br0 entered promiscuous mode
[   15.508944] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[   15.520558] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   15.531358] dwmac1000: Master AXI performs any burst length
[   15.531386] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[   15.545826] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   15.545943] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   15.553746] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[   15.560715] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   15.569350] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   15.583881] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[   15.592088] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   15.602826] dwmac1000: Master AXI performs any burst length
[   15.602854] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[   15.617272] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   15.617395] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   15.625192] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[   15.632086] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   15.640734] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   15.651202] br0: port 1(eth0) entered blocking state
[   15.655577] br0: port 1(eth0) entered disabled state
[   15.660870] device eth0 entered promiscuous mode
[   15.665776] br0: port 1(eth0) entered blocking state
[   15.670257] br0: port 1(eth0) entered forwarding state
[   15.675324] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[   15.693700] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[   15.706735] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[   15.717473] dwmac1000: Master AXI performs any burst length
[   15.717502] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[   15.731858] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   15.731980] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   15.739780] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[   15.746825] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   15.755391] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   15.769853] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[   15.778261] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[   15.788998] dwmac1000: Master AXI performs any burst length
[   15.789026] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[   15.803454] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   15.803571] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   15.811304] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[   15.818378] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   15.826920] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   15.837462] br0: port 2(eth1) entered blocking state
[   15.841682] br0: port 2(eth1) entered disabled state
[   15.847118] device eth1 entered promiscuous mode
[   15.851870] br0: port 2(eth1) entered blocking state
[   15.856488] br0: port 2(eth1) entered forwarding state
[   15.873524] device br0 left promiscuous mode
[   15.876486] device br0 entered promiscuous mode
[   15.884598] device br0 left promiscuous mode
[   15.994249] ath: EEPROM regdomain: 0x8348
[   15.994264] ath: EEPROM indicates we should expect a country code
[   15.994270] ath: doing EEPROM country->regdmn map search
[   15.994275] ath: country maps to regdmn code: 0x3a
[   15.994280] ath: Country alpha2 being used: US
[   15.994285] ath: Regpair used: 0x3a
[   15.994290] ath: regdomain 0x8348 dynamically updated by user
[   15.994348] ath: EEPROM regdomain: 0x8348
[   15.994354] ath: EEPROM indicates we should expect a country code
[   15.994360] ath: doing EEPROM country->regdmn map search
[   15.994366] ath: country maps to regdmn code: 0x3a
[   15.994372] ath: Country alpha2 being used: US
[   15.994376] ath: Regpair used: 0x3a
[   15.994381] ath: regdomain 0x8348 dynamically updated by user
[   16.037956] ath: EEPROM regdomain: 0x8348
[   16.037970] ath: EEPROM indicates we should expect a country code
[   16.037977] ath: doing EEPROM country->regdmn map search
[   16.037982] ath: country maps to regdmn code: 0x3a
[   16.037988] ath: Country alpha2 being used: US
[   16.037994] ath: Regpair used: 0x3a
[   16.037999] ath: regdomain 0x8348 dynamically updated by user
[   16.038053] ath: EEPROM regdomain: 0x8348
[   16.038059] ath: EEPROM indicates we should expect a country code
[   16.038064] ath: doing EEPROM country->regdmn map search
[   16.038068] ath: country maps to regdmn code: 0x3a
[   16.038073] ath: Country alpha2 being used: US
[   16.038078] ath: Regpair used: 0x3a
[   16.038084] ath: regdomain 0x8348 dynamically updated by user
[   16.782227] tun: Universal TUN/TAP device driver, 1.6
[   20.780588] usbcore: registered new interface driver usbfs
[   20.780655] usbcore: registered new interface driver hub
[   20.785125] usbcore: registered new device driver usb
[   21.533808] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[   21.533864] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[   21.538578] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[   21.545868] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x10000000
[   21.555333] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[   21.561033] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[   21.566639] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[   21.577024] hub 1-0:1.0: USB hub found
[   21.580761] hub 1-0:1.0: 1 port detected
[   21.584847] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[   21.588972] hub 2-0:1.0: USB hub found
[   21.596767] hub 2-0:1.0: 1 port detected
[   21.654000] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[   21.654048] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[   21.658763] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[   21.666084] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x11000000
[   21.675565] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[   21.681218] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[   21.686849] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[   21.687409] hub 3-0:1.0: USB hub found
[   21.700935] hub 3-0:1.0: 1 port detected
[   21.705064] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[   21.709154] hub 4-0:1.0: USB hub found
[   21.716922] hub 4-0:1.0: 1 port detected
[   21.893363] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[   22.294310] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[   23.263478] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[   26.524974] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   26.525012] usb usb4: USB disconnect, device number 1
[   26.529007] usb 4-1: USB disconnect, device number 2
[   26.535156] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   26.539092] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   26.544796] usb usb3: USB disconnect, device number 1
[   26.550698] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   26.554867] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   26.560440] usb usb2: USB disconnect, device number 1
[   26.565929] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[   26.570429] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   26.576248] usb usb1: USB disconnect, device number 1
[   26.581094] usb 1-1: USB disconnect, device number 2
[   26.587846] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[   26.644551] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[   26.644601] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[   26.649316] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[   26.656584] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0x10000000
[   26.666118] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[   26.671767] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[   26.677405] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[   26.685401] hub 1-0:1.0: USB hub found
[   26.691501] hub 1-0:1.0: 1 port detected
[   26.695606] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[   26.699704] hub 2-0:1.0: USB hub found
[   26.707462] hub 2-0:1.0: 1 port detected
[   26.711302] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[   26.715103] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[   26.720674] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[   26.727952] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x11000000
[   26.737465] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[   26.743121] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[   26.748755] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[   26.756778] hub 3-0:1.0: USB hub found
[   26.762859] hub 3-0:1.0: 1 port detected
[   26.766949] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[   26.771064] hub 4-0:1.0: USB hub found
[   26.778811] hub 4-0:1.0: 1 port detected
[   26.843704] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[   26.945659] SCSI subsystem initialized
[   27.015618] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[   27.143475] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[   27.401400] usb-storage 4-1:1.0: USB Mass Storage device detected
[   27.401858] scsi host0: usb-storage 4-1:1.0
[   27.406801] usb-storage 1-1:1.0: USB Mass Storage device detected
[   27.410861] scsi host1: usb-storage 1-1:1.0
[   27.417679] usbcore: registered new interface driver usb-storage
[   27.474159] libata version 3.00 loaded.
[   27.639473] ahci 29000000.sata: supply ahci not found, using dummy regulator
[   27.639630] ahci 29000000.sata: supply phy not found, using dummy regulator
[   27.645794] ahci 29000000.sata: supply target not found, using dummy regulator
[   27.653344] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[   27.659588] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[   27.665119] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst 
[   27.674622] scsi host2: ahci
[   27.682129] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 50
[   28.016572] ata1: SATA link down (SStatus 0 SControl 300)
[   28.255342] sdhci: Secure Digital Host Controller Interface driver
[   28.255376] sdhci: Copyright(c) Pierre Ossman
[   28.306410] sdhci-pltfm: SDHCI platform and OF driver helper
[   28.474600] scsi 1:0:0:0: Direct-Access              USB Flash Drive  1.00 PQ: 0 ANSI: 6
[   28.475909] sd 1:0:0:0: [sda] 30629376 512-byte logical blocks: (15.7 GB/14.6 GiB)
[   28.483133] sd 1:0:0:0: [sda] Write Protect is off
[   28.489252] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[   28.489973] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   28.500775]  sda: sda1
[   28.503471] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   28.619183] ksmbd: kill command received
[   28.706942] scsi 0:0:0:0: Direct-Access     Samsung  Flash Drive      1100 PQ: 0 ANSI: 6
[   28.742295] sd 0:0:0:0: [sdb] 62656641 512-byte logical blocks: (32.1 GB/29.9 GiB)
[   28.754659] sd 0:0:0:0: [sdb] Write Protect is off
[   28.759787] sd 0:0:0:0: [sdb] Mode Sense: 43 00 00 00
[   28.760564] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   28.918152] sd 0:0:0:0: [sdb] Attached SCSI removable disk
[   29.043843] br1: port 1(eth1.15) entered blocking state
[   29.043880] br1: port 1(eth1.15) entered disabled state
[   29.048068] device eth1.15 entered promiscuous mode
[   29.057077] br1: port 1(eth1.15) entered blocking state
[   29.654864] EXT4-fs: Ignoring removed nobh option
[   29.659513] EXT4-fs (sda1): barriers disabled
[   29.665156] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none.
[   48.094195] br1: port 1(eth1.15) entered learning state
root@EA8500:~# uptime && date
 17:28:43 up 1 min,  load average: 0.37, 0.15, 0.05
Thu Oct 19 17:28:43 CDT 2023
root@EA8500:~#