DD-WRT v3.0-r33784 std (c) 2017 NewMedia-NET GmbH
Release: 11/19/17
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
http://www.dd-wrt.com
==========================================================
BusyBox v1.27.2 (2017-11-19 02:02:28 CET) built-in shell (ash)
root@~~:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.18.82 (root@seg-desktop) (gcc version 7.1.0 (LEDE GCC 7.1.0 r4105-9448e16959) ) #198 SMP PREEMPT Sat Nov 18 22:57:32 CET 2017
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: Linksys EA8500 WiFi Router
[ 0.000000] Ignoring memory range 0x41500000 - 0x42000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 122880
[ 0.000000] free_area_init_node: node 0, pgdat c071c840, node_mem_map ddb40000
[ 0.000000] Normal zone: 960 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 122880 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 9 pages/cpu @ddfd3000 s7552 r8192 d21120 u36864
[ 0.000000] pcpu-alloc: s7552 r8192 d21120 u36864 alloc=9*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 481332K/491520K available (3842K kernel code, 279K rwdata, 1108K rodata, 184K init, 310K bss, 10188K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff000000 ( 520 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc06dde14 (4952 kB)
[ 0.000000] .init : 0xc06de000 - 0xc070c000 ( 184 kB)
[ 0.000000] .data : 0xc070c000 - 0xc0751c04 ( 280 kB)
[ 0.000000] .bss : 0xc0751c04 - 0xc079f788 ( 311 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000014] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 687194767200ns
[ 0.000029] Switching to timer-based delay loop, resolution 160ns
[ 0.000421] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000442] pid_max: default: 32768 minimum: 301
[ 0.000683] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000699] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001350] CPU: Testing write buffer coherency: ok
[ 0.001614] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002142] Setting up static identity map for 0x422130d0 - 0x42213128
[ 0.063434] CPU1: Booted secondary processor
[ 0.063567] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.063678] Brought up 2 CPUs
[ 0.063701] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.063712] CPU: All CPU(s) started in SVC mode.
[ 0.078668] VFP support v0.3: implementor 51 architecture 0 part 4d variant 2 rev 0
[ 0.079181] pinctrl core: initialized pinctrl subsystem
[ 0.089595] NET: Registered protocol family 16
[ 0.089930] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.113851] cpuidle: using governor ladder
[ 0.144868] cpuidle: using governor menu
[ 0.163864] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 0.163944] qcom_rpm 108000.rpm: failed to mark ack irq as wakeup
[ 0.164002] qcom_rpm 108000.rpm: failed to mark wakeup irq as wakeup
[ 0.199490] pps_core: LinuxPPS API ver. 1 registered
[ 0.199503] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.199547] PTP clock support registered
[ 0.200660] pcie_init: pcie_init: unable to create IPC log context for pcie0-short
[ 0.200675] pcie_init: pcie_init: unable to create IPC log context for pcie0-long
[ 0.200688] pcie_init: pcie_init: unable to create IPC log context for pcie1-short
[ 0.200697] pcie_init: pcie_init: unable to create IPC log context for pcie1-long
[ 0.201094] Switched to clocksource dg_timer
[ 0.202552] NET: Registered protocol family 2
[ 0.203265] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.203306] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.203358] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.203403] TCP: reno registered
[ 0.203422] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.203444] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.203684] NET: Registered protocol family 1
[ 0.203745] PCI: CLS 0 bytes, default 64
[ 0.204837] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.204937] Crashlog allocated RAM at address 0x5ff00000
[ 0.205845] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.205877] msgmni has been set to 940
[ 0.207882] io scheduler noop registered
[ 0.207903] io scheduler deadline registered (default)
[ 0.209254] 1b500000.pci supply vdda not found, using dummy regulator
[ 0.209342] 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.209421] 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.240416] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.240439] pci_bus 0000:00: root bus resource [io 0xfe00000-0xfffff] (bus address [0x1fc00000-0xfefffff])
[ 0.240454] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.240470] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.240518] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.240654] pci 0000:00:00.0: supports D1
[ 0.240670] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.240986] PCI: bus0: Fast back to back transfers disabled
[ 0.241407] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.241609] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.242553] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.242983] PCI: bus1: Fast back to back transfers disabled
[ 0.243003] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.243156] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.243179] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.243289] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.243310] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.243763] aer 0000:00:00.0:pcie02: service driver aer loaded
[ 0.244107] 1b700000.pci supply vdda not found, using dummy regulator
[ 0.244194] 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.244288] 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.274512] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.274532] pci_bus 0001:00: root bus resource [io 0x31e10000-0xfffff] (bus address [0x63c00000-0x31eeffff])
[ 0.274547] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.274562] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.274606] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.274726] pci 0001:00:00.0: supports D1
[ 0.274740] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.275055] PCI: bus0: Fast back to back transfers disabled
[ 0.275387] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.275584] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.276522] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.276944] PCI: bus1: Fast back to back transfers disabled
[ 0.276961] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.277176] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.277197] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.277303] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 0.277323] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.277716] aer 0001:00:00.0:pcie02: service driver aer loaded
[ 0.278052] 1b900000.pci supply vdda not found, using dummy regulator
[ 0.278136] 1b900000.pci supply vdda_phy not found, using dummy regulator
[ 0.278215] 1b900000.pci supply vdda_refclk not found, using dummy regulator
[ 0.413026] qcom-pcie 1b900000.pci: link initialization failed
[ 0.415134] qcom-pcie 1b900000.pci: PCI host bridge to bus 0002:00
[ 0.415154] pci_bus 0002:00: root bus resource [io 0x35e20000-0xfffff] (bus address [0x6bc00000-0x35edffff])
[ 0.415169] pci_bus 0002:00: root bus resource [mem 0x32000000-0x35dfffff]
[ 0.415191] pci_bus 0002:00: root bus resource [bus 00-ff]
[ 0.415241] PCI: bus0: Fast back to back transfers enabled
[ 0.417806] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.419126] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.420127] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.420222] msm_serial 16340000.serial: uartclk = 1843200
[ 0.420283] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 184, base_baud = 115200) is a MSM
[ 0.420338] msm_serial: console setup on port #0
[ 1.134819] console [ttyMSM0] enabled
[ 1.139585] msm_serial: driver initialized
[ 1.146392] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 1.146865] nand: AMD/Spansion S34MS01G2
[ 1.153445] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 1.157288] Scanning device for bad blocks
[ 1.568021] random: nonblocking pool is initialized
[ 1.869976] 19 ofpart partitions found on MTD device qcom-nandc
[ 1.870005] Creating 19 MTD partitions on "qcom-nandc":
[ 1.874792] 0x000000000000-0x000000040000 : "SBL1"
[ 1.880799] 0x000000040000-0x000000180000 : "MIBIB"
[ 1.885641] 0x000000180000-0x0000002c0000 : "SBL2"
[ 1.890310] 0x0000002c0000-0x000000540000 : "SBL3"
[ 1.895250] 0x000000540000-0x000000660000 : "DDRCONFIG"
[ 1.899962] 0x000000660000-0x000000780000 : "SSD"
[ 1.905125] 0x000000780000-0x000000a00000 : "TZ"
[ 1.909944] 0x000000a00000-0x000000c80000 : "RPM"
[ 1.914731] 0x000000c80000-0x000000dc0000 : "art"
[ 1.919220] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[ 1.923988] 0x000000ec0000-0x000000f00000 : "u_env"
[ 1.928977] 0x000000f00000-0x000000f40000 : "s_env"
[ 1.933650] 0x000000f40000-0x000000f80000 : "devinfo"
[ 1.938419] 0x000000f80000-0x000003780000 : "linux"
[ 1.943730] 0x000001280000-0x000003780000 : "rootfs"
[ 1.948349] mtd: partition "rootfs" set to be root filesystem
[ 1.952820] 0x000003780000-0x000005f40000 : "linux2"
[ 1.959204] 0x000003a80000-0x000005f40000 : "rootfs2"
[ 1.964300] 0x000005f40000-0x000005f80000 : "nvram"
[ 1.969149] 0x000005f80000-0x000008000000 : "ddwrt"
[ 1.975192] IMQ: autocreate imq0 NS c074bec0
[ 1.978458] IMQ: autocreate imq1 NS c074bec0
[ 1.982496] IMQ driver loaded successfully. (numdevs = 16, numqueues = 1)
[ 1.986764] Hooking IMQ after NAT on PREROUTING.
[ 1.993605] Hooking IMQ before NAT on POSTROUTING.
[ 1.998542] libphy: Fixed MDIO Bus: probed
[ 2.003424] libphy: GPIO Bitbanged MDIO: probed
[ 2.028165] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 2.830929] tun: Universal TUN/TAP device driver, 1.6
[ 2.830953] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.836527] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.841030] Ring mode enabled
[ 2.846258] DMA HW capability register supported
[ 2.849102] Enhanced/Alternate descriptors
[ 2.853875] Enabled extended descriptors
[ 2.857868] RX Checksum Offload Engine supported (type 2)
[ 2.862110] TX Checksum insertion supported
[ 2.867416] Wake-Up On Lan supported
[ 2.871998] Enable RX Mitigation via HW Watchdog Timer
[ 2.876638] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.880441] Ring mode enabled
[ 2.885742] DMA HW capability register supported
[ 2.888598] Enhanced/Alternate descriptors
[ 2.893370] Enabled extended descriptors
[ 2.897363] RX Checksum Offload Engine supported (type 2)
[ 2.901603] TX Checksum insertion supported
[ 2.906913] Wake-Up On Lan supported
[ 2.911395] Enable RX Mitigation via HW Watchdog Timer
[ 2.915671] PPP generic driver version 2.4.2
[ 2.920079] PPP BSD Compression module registered
[ 2.924552] PPP Deflate Compression module registered
[ 2.929069] PPP MPPE Compression module registered
[ 2.934174] NET: Registered protocol family 24
[ 2.938816] PPTP driver version 0.8.5
[ 2.943413] i2c /dev entries driver
[ 2.952657] Speed bin: 0
[ 2.952679] PVS bin: 1
[ 2.954670] platform cpufreq-krait.0: Driver cpufreq-krait requests probe deferral
[ 2.958344] L2 @ QSB rate. Forcing new rate.
[ 2.964289] L2 @ 387500 KHz
[ 2.968522] CPU0 @ 800000 KHz
[ 2.970917] CPU1 @ QSB rate. Forcing new rate.
[ 2.974195] CPU1 @ 384000 KHz
[ 2.978676] GACT probability NOT on
[ 2.981498] Mirror/redirect action on
[ 2.984756] Simple TC action Loaded
[ 2.989368] netem: version 1.3
[ 2.991980] u32 classifier
[ 2.994959] Performance counters on
[ 2.997651] input device check on
[ 3.001473] Actions configured
[ 3.005256] Netfilter messages via NETLINK v0.30.
[ 3.008570] nf_conntrack version 0.5.0 (7520 buckets, 30080 max)
[ 3.013688] nf_conntrack_rtsp v0.7 loading
[ 3.019929] xt_time: kernel timezone is -0000
[ 3.023377] ip_set: protocol 6
[ 3.027969] gre: GRE over IPv4 demultiplexor driver
[ 3.030868] nf_nat_rtsp v0.7 loading
[ 3.035546] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.039466] TCP: bic registered
[ 3.044625] TCP: cubic registered
[ 3.047399] TCP: westwood registered
[ 3.050875] TCP: highspeed registered
[ 3.054684] TCP: hybla registered
[ 3.058076] TCP: htcp registered
[ 3.061464] TCP: vegas registered
[ 3.064672] TCP: veno registered
[ 3.067888] TCP: scalable registered
[ 3.071184] TCP: lp registered
[ 3.074804] TCP: yeah registered
[ 3.077609] TCP: illinois registered
[ 3.080998] NET: Registered protocol family 17
[ 3.084717] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 3.088858] Bridge firewalling registered
[ 3.101640] 8021q: 802.1Q VLAN Support v1.8
[ 3.105610] Registering SWP/SWPB emulation handler
[ 3.113442] trying to register driver generic_krait
[ 3.114340] Frequency table not initialized.
[ 3.119219] Frequency table not initialized.
[ 3.123726] Frequency table not initialized.
[ 3.127864] Frequency table not initialized.
[ 3.132187] Frequency table not initialized.
[ 3.137915] Frequency table not initialized.
[ 3.140686] Frequency table not initialized.
[ 3.144944] Frequency table not initialized.
[ 3.149127] Frequency table not initialized.
[ 3.153476] Frequency table not initialized.
[ 3.157648] driver generic_krait up and running
[ 3.161996] searching for nvram
[ 3.166164] nvram size = -1066992914
[ 3.190482] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 3.198492] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 3.201393] VFS: Mounted root (squashfs filesystem) readonly on device 31:14.
[ 3.205187] Freeing unused kernel memory: 184K
[ 5.747255] UBIFS error (pid 712): ubifs_mount: cannot open "ubi0:rootfs_data", error -19
[ 6.818689] Loading modules backported from Linux version wireless-drivers-next-for-davem-2017-09-01-0-geb464d4a8d09
[ 6.818721] Backport generated by backports.git backports-20160324-111-g97b8d7c4
[ 7.319236] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 7.319896] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 7.453628] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[ 7.453708] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 7.465250] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[ 7.469387] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 7.820442] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 7.820490] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[ 7.832475] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.5.3-00038 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 b1d4e84d
[ 8.711479] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 8.731499] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 10.133455] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
[ 10.133652] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 3e376c3f
[ 11.338386] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1
[ 11.414167] ath: EEPROM regdomain: 0x0
[ 11.414186] ath: EEPROM indicates default country code should be used
[ 11.414200] ath: doing EEPROM country->regdmn map search
[ 11.414220] ath: country maps to regdmn code: 0x3a
[ 11.414236] ath: Country alpha2 being used: US
[ 11.414250] ath: Regpair used: 0x3a
[ 11.425742] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 11.426435] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.553462] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
[ 11.553505] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 11.564969] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[ 11.569222] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 11.581440] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
[ 11.585892] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[ 11.598835] ath10k_pci 0001:01:00.0: firmware ver 10.4-3.5.3-00038 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 b1d4e84d
[ 13.890801] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
[ 13.891003] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 eca6e637
[ 15.096031] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1
[ 15.163656] ath: EEPROM regdomain: 0x0
[ 15.163676] ath: EEPROM indicates default country code should be used
[ 15.163692] ath: doing EEPROM country->regdmn map search
[ 15.163714] ath: country maps to regdmn code: 0x3a
[ 15.163730] ath: Country alpha2 being used: US
[ 15.163745] ath: Regpair used: 0x3a
[ 15.317604] usbcore: registered new interface driver usbfs
[ 15.318023] usbcore: registered new interface driver hub
[ 15.322295] usbcore: registered new device driver usb
[ 15.356505] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 15.364387] ehci-platform: EHCI generic platform driver
[ 15.383426] ehci-pci: EHCI PCI platform driver
[ 15.421781] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 15.576388] soc:usb30@0 supply gdsc not found, using dummy regulator
[ 15.577161] platform 11000000.dwc3: Driver dwc3 requests probe deferral
[ 15.582147] platform 11000000.dwc3: Driver dwc3 requests probe deferral
[ 15.588212] soc:usb30@1 supply gdsc not found, using dummy regulator
[ 15.595504] platform 10000000.dwc3: Driver dwc3 requests probe deferral
[ 15.601676] platform 11000000.dwc3: Driver dwc3 requests probe deferral
[ 15.607852] platform 10000000.dwc3: Driver dwc3 requests probe deferral
[ 15.638115] 100f8800.phy supply vddcx not found, using dummy regulator
[ 15.638218] 100f8800.phy supply v3p3 not found, using dummy regulator
[ 15.643694] 100f8800.phy supply v1p8 not found, using dummy regulator
[ 15.650099] 100f8800.phy supply vbus not found, using dummy regulator
[ 15.656926] platform 11000000.dwc3: Driver dwc3 requests probe deferral
[ 15.663033] 110f8800.phy supply vddcx not found, using dummy regulator
[ 15.669366] 110f8800.phy supply v3p3 not found, using dummy regulator
[ 15.676066] 110f8800.phy supply v1p8 not found, using dummy regulator
[ 15.676170] platform 10000000.dwc3: Driver dwc3 requests probe deferral
[ 15.688923] 110f8800.phy supply vbus not found, using dummy regulator
[ 15.695638] platform 11000000.dwc3: Driver dwc3 requests probe deferral
[ 15.702538] platform 10000000.dwc3: Driver dwc3 requests probe deferral
[ 15.715638] 100f8830.phy supply vddcx not found, using dummy regulator
[ 15.715729] 100f8830.phy supply v1p8 not found, using dummy regulator
[ 15.721698] qcom-dwc3-ssphy 100f8830.phy: cannot get HSIO settings from device node, using default values
[ 15.728068] 110f8830.phy supply vddcx not found, using dummy regulator
[ 15.728165] platform 11000000.dwc3: Driver dwc3 requests probe deferral
[ 15.728361] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for vddcx
[ 15.728366] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for v3p3
[ 15.728371] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for v1p8
[ 15.730807] qcom-dwc3-ssphy 100f8830.phy: cannot set voltage for vddcx
[ 15.770087] 110f8830.phy supply v1p8 not found, using dummy regulator
[ 15.776592] qcom-dwc3-ssphy 110f8830.phy: cannot get HSIO settings from device node, using default values
[ 15.972735] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 15.972830] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 15.977298] xhci-hcd xhci-hcd.0.auto: irq 237, io mem 0x10000000
[ 15.985519] hub 1-0:1.0: USB hub found
[ 15.991140] hub 1-0:1.0: 1 port detected
[ 15.995230] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 15.998566] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 16.004732] hub 2-0:1.0: USB hub found
[ 16.011696] hub 2-0:1.0: 1 port detected
[ 16.015947] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for vddcx
[ 16.019301] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for v3p3
[ 16.025768] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for v1p8
[ 16.034646] qcom-dwc3-ssphy 110f8830.phy: cannot set voltage for vddcx
[ 16.282566] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 16.282618] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 16.287135] xhci-hcd xhci-hcd.1.auto: irq 142, io mem 0x11000000
[ 16.295325] hub 3-0:1.0: USB hub found
[ 16.300769] hub 3-0:1.0: 1 port detected
[ 16.304786] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 16.308400] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 16.314548] hub 4-0:1.0: USB hub found
[ 16.321260] hub 4-0:1.0: 1 port detected
[ 16.622710] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 20.828315] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 20.828360] usb usb4: USB disconnect, device number 1
[ 20.834296] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 20.837418] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 20.849324] usb usb3: USB disconnect, device number 1
[ 20.849356] usb 3-1: USB disconnect, device number 2
[ 20.857755] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 20.858455] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 20.875562] usb usb2: USB disconnect, device number 1
[ 20.877286] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 20.879631] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 20.895064] usb usb1: USB disconnect, device number 1
[ 20.897001] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 20.915295] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 20.915411] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 20.919887] xhci-hcd xhci-hcd.0.auto: irq 237, io mem 0x10000000
[ 20.928930] hub 1-0:1.0: USB hub found
[ 20.933885] hub 1-0:1.0: 1 port detected
[ 20.937716] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 20.941146] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 20.948321] hub 2-0:1.0: USB hub found
[ 20.954386] hub 2-0:1.0: 1 port detected
[ 20.958539] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 20.962109] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 20.967403] xhci-hcd xhci-hcd.1.auto: irq 142, io mem 0x11000000
[ 20.976352] hub 3-0:1.0: USB hub found
[ 20.981307] hub 3-0:1.0: 1 port detected
[ 20.985250] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 20.989019] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 20.995557] hub 4-0:1.0: USB hub found
[ 21.001815] hub 4-0:1.0: 1 port detected
[ 21.051801] SCSI subsystem initialized
[ 21.136278] usbcore: registered new interface driver usb-storage
[ 21.198149] libata version 3.00 loaded.
[ 21.288333] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[ 21.288387] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 21.292802] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 21.302291] scsi host0: ahci_platform
[ 21.309964] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241
[ 21.313440] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 21.465382] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 21.469911] scsi host1: usb-storage 3-1:1.0
[ 21.661791] ata1: SATA link down (SStatus 0 SControl 300)
[ 22.472462] scsi 1:0:0:0: Direct-Access PNY USB 2.0 FD 0.00 PQ: 0 ANSI: 2
[ 22.475014] sd 1:0:0:0: [sda] 31711232 512-byte logical blocks: (16.2 GB/15.1 GiB)
[ 22.480466] sd 1:0:0:0: [sda] Write Protect is off
[ 22.487060] sd 1:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 22.487900] sd 1:0:0:0: [sda] Asking for cache data failed
[ 22.491834] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 22.500730] sda: sda1
[ 22.515894] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 22.718563] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 22.726849] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 22.891978] using kernel STP
[ 23.165024] device br0 entered promiscuous mode
[ 23.208089] device vlan1 entered promiscuous mode
[ 23.208110] device eth0 entered promiscuous mode
[ 23.211931] br0: port 1(vlan1) entered forwarding state
[ 23.216465] br0: port 1(vlan1) entered forwarding state
[ 23.228764] device br0 left promiscuous mode
[ 23.230900] device br0 entered promiscuous mode
[ 23.272809] device br0 left promiscuous mode
[ 23.324188] ath: EEPROM regdomain: 0x8348
[ 23.324195] ath: EEPROM indicates we should expect a country code
[ 23.324202] ath: doing EEPROM country->regdmn map search
[ 23.324208] ath: country maps to regdmn code: 0x3a
[ 23.324214] ath: Country alpha2 being used: US
[ 23.324220] ath: Regpair used: 0x3a
[ 23.324227] ath: regdomain 0x8348 dynamically updated by user
[ 23.324243] ath: EEPROM regdomain: 0x8348
[ 23.324247] ath: EEPROM indicates we should expect a country code
[ 23.324253] ath: doing EEPROM country->regdmn map search
[ 23.324258] ath: country maps to regdmn code: 0x3a
[ 23.324263] ath: Country alpha2 being used: US
[ 23.324267] ath: Regpair used: 0x3a
[ 23.324272] ath: regdomain 0x8348 dynamically updated by user
[ 25.211954] br0: port 1(vlan1) entered forwarding state
[ 29.065284] device ath0 entered promiscuous mode
[ 31.235571] br0: port 2(ath0) entered forwarding state
[ 31.235614] br0: port 2(ath0) entered forwarding state
[ 31.248613] device ath0.1 entered promiscuous mode
[ 31.256141] br1: port 1(ath0.1) entered listening state
[ 31.256172] br1: port 1(ath0.1) entered listening state
[ 32.873716] device ath1 entered promiscuous mode
[ 33.231453] br0: port 2(ath0) entered forwarding state
[ 33.256599] br1: port 1(ath0.1) entered learning state
[ 33.628231] device ath1.1 entered promiscuous mode
[ 33.642611] br1: port 2(ath1.1) entered listening state
[ 33.642644] br1: port 2(ath1.1) entered listening state
[ 33.671026] br0: port 3(ath1) entered forwarding state
[ 33.671079] br0: port 3(ath1) entered forwarding state
[ 34.117413] device vlan2 entered promiscuous mode
[ 35.028177] device vlan2 left promiscuous mode
[ 35.251461] br1: topology change detected, propagating
[ 35.251497] br1: port 1(ath0.1) entered forwarding state
[ 35.641477] br1: port 2(ath1.1) entered learning state
[ 35.661467] br0: port 3(ath1) entered forwarding state
[ 36.574952] device vlan4 entered promiscuous mode
[ 36.575024] br1: port 3(vlan4) entered listening state
[ 36.578653] br1: port 3(vlan4) entered listening state
[ 37.641539] br1: topology change detected, propagating
[ 37.641584] br1: port 2(ath1.1) entered forwarding state
[ 38.571464] br1: port 3(vlan4) entered learning state
[ 40.571478] br1: topology change detected, propagating
[ 40.571503] br1: port 3(vlan4) entered forwarding state
[ 43.134712] Ebtables v2.0 registered
[ 610.223372] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
[ 1015.108236] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1015.174459] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1015.177658] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1015.220118] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1042.134834] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1042.151167] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1062.166909] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1062.168198] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1062.195927] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1062.197333] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 1956.855150] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[ 1956.855192] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[ 1956.862411] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[ 1956.870473] ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in push mode
[ 2772.744527] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 2785.284859] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4655.064331] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4655.079500] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4655.080845] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4655.093779] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4675.110637] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4675.110857] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4675.124950] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4675.125584] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4695.169070] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4695.171099] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4695.202776] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4695.203979] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4716.171659] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4716.185191] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4736.202679] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4736.219018] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4756.272629] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4756.307393] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4776.299687] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4776.312267] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4796.327617] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4796.364935] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4816.325849] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4816.338676] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4836.376347] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4836.377752] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4836.398151] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4836.399610] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4856.415005] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4856.453564] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4876.443278] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4876.471500] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4896.446067] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4896.446716] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4896.459304] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4896.460507] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4916.518135] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4916.519879] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4916.547713] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4916.549987] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4937.504103] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
[ 4937.517944] ath10k_pci 0000:01:00.0: Unknown eventid: 36925
root@~~:~# uptime
20:21:47 up 1:38, load average: 0.00, 0.04, 0.07
root@~~:~# nvram get DD_BOARD
Linksys EA8500
root@~~:~# cat /tmp/loginprompt
DD-WRT v3.0-r33784 std (c) 2017 NewMedia-NET GmbH
Release: 11/19/17
root@~~:~# uptime
20:22:54 up 1:39, load average: 0.00, 0.03, 0.06
root@~~:~# date
Sun Nov 19 20:22:56 CST 2017
root@~~:~# exit
Connection to ~~.mrjcd.com closed.
mrjcd@bigdeb:~$