U-Boot .07 [Standard IPQ806X.LN,r40331] (Apr 24 2015 - 09:08:25)

CBT U-Boot ver: 1.0.10

smem ram ptable found: ver: 0 len: 5
DRAM:  491 MiB
NAND:  SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:   
PCI0 Link Intialized
PCI1 Link Intialized
In:    serial
Out:   serial
Err:   serial
cdp: get part failed for 0:HLOS
Net:   MAC1 addr:0:3:7f:ba:db:1
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init  done
MAC2 addr:0:3:7f:ba:db:2
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         00:03:7f:ba:db:01
Address in environment is  00:06:3b:01:41:00
, eth1

Updating boot_count ... done

Hit any key to stop autoboot:  0 
Write Reg: 0x00000660: Oldval = 0x00140020 Newval = 0x0014007e
Write Reg: 0x0000066c: Oldval = 0x0014005c Newval = 0x0014007d
Write Reg: 0x00000678: Oldval = 0x0014005a Newval = 0x0014007b
Write Reg: 0x00000684: Oldval = 0x00140056 Newval = 0x00140077
Write Reg: 0x00000690: Oldval = 0x0014004e Newval = 0x0014006f
Write Reg: 0x0000069c: Oldval = 0x00140001 Newval = 0x0014005f
Write Reg: 0x000006a8: Oldval = 0x0014001e Newval = 0x0014003f
Write Reg: 0x00000420: Oldval = 0x00020001 Newval = 0x00010001
Write Reg: 0x00000428: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000430: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000438: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000440: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000448: Oldval = 0x00020001 Newval = 0x00010001
Write Reg: 0x00000450: Oldval = 0x00010001 Newval = 0x00010001
(IPQ) # setenv image EA8500-factory-to-ddwrt.img


(IPQ) # setenv ipaddr 192.168.1.1


(IPQ) # setenv serverip 192.168.1.7


(IPQ) # run flashimg


Mac1 unit failed
Using eth1 device
TFTP from server 192.168.1.7; our IP address is 192.168.1.1
Filename 'EA8500-factory-to-ddwrt.img'.
Load address: 0x42000000
Loading: #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #####################################
done
Bytes transferred = 24393983 (17438ff hex)

NAND erase: device 0 offset 0xf80000, size 0x17438ff

Erasing at 0xf80000 --   0% complete.
Erasing at 0xfa0000 --   1% complete.
Erasing at 0xfe0000 --   2% complete.
Erasing at 0x1020000 --   3% complete.
Erasing at 0x1060000 --   4% complete.
Erasing at 0x10a0000 --   5% complete.
Erasing at 0x10e0000 --   6% complete.
Erasing at 0x1120000 --   7% complete.
Erasing at 0x1140000 --   8% complete.
Erasing at 0x1180000 --   9% complete.
Erasing at 0x11c0000 --  10% complete.
Erasing at 0x1200000 --  11% complete.
Erasing at 0x1240000 --  12% complete.
Erasing at 0x1280000 --  13% complete.
Erasing at 0x12c0000 --  14% complete.
Erasing at 0x1300000 --  15% complete.
Erasing at 0x1320000 --  16% complete.
Erasing at 0x1360000 --  17% complete.
Erasing at 0x13a0000 --  18% complete.
Erasing at 0x13e0000 --  19% complete.
Erasing at 0x1420000 --  20% complete.
Erasing at 0x1460000 --  21% complete.
Erasing at 0x14a0000 --  22% complete.
Erasing at 0x14e0000 --  23% complete.
Erasing at 0x1500000 --  24% complete.
Erasing at 0x1540000 --  25% complete.
Erasing at 0x1580000 --  26% complete.
Erasing at 0x15c0000 --  27% complete.
Erasing at 0x1600000 --  28% complete.
Erasing at 0x1640000 --  29% complete.
Erasing at 0x1680000 --  30% complete.
Erasing at 0x16a0000 --  31% complete.
Erasing at 0x16e0000 --  32% complete.
Erasing at 0x1720000 --  33% complete.
Erasing at 0x1760000 --  34% complete.
Erasing at 0x17a0000 --  35% complete.
Erasing at 0x17e0000 --  36% complete.
Erasing at 0x1820000 --  37% complete.
Erasing at 0x1860000 --  38% complete.
Erasing at 0x1880000 --  39% complete.
Erasing at 0x18c0000 --  40% complete.
Erasing at 0x1900000 --  41% complete.
Erasing at 0x1940000 --  42% complete.
Erasing at 0x1980000 --  43% complete.
Erasing at 0x19c0000 --  44% complete.
Erasing at 0x1a00000 --  45% complete.
Erasing at 0x1a40000 --  46% complete.
Erasing at 0x1a60000 --  47% complete.
Erasing at 0x1aa0000 --  48% complete.
Erasing at 0x1ae0000 --  49% complete.
Erasing at 0x1b20000 --  50% complete.
Erasing at 0x1b60000 --  51% complete.
Erasing at 0x1ba0000 --  52% complete.
Erasing at 0x1be0000 --  53% complete.
Erasing at 0x1c00000 --  54% complete.
Erasing at 0x1c40000 --  55% complete.
Erasing at 0x1c80000 --  56% complete.
Erasing at 0x1cc0000 --  57% complete.
Erasing at 0x1d00000 --  58% complete.
Erasing at 0x1d40000 --  59% complete.
Erasing at 0x1d80000 --  60% complete.
Erasing at 0x1dc0000 --  61% complete.
Erasing at 0x1de0000 --  62% complete.
Erasing at 0x1e20000 --  63% complete.
Erasing at 0x1e60000 --  64% complete.
Erasing at 0x1ea0000 --  65% complete.
Erasing at 0x1ee0000 --  66% complete.
Erasing at 0x1f20000 --  67% complete.
Erasing at 0x1f60000 --  68% complete.
Erasing at 0x1fa0000 --  69% complete.
Erasing at 0x1fc0000 --  70% complete.
Erasing at 0x2000000 --  71% complete.
Erasing at 0x2040000 --  72% complete.
Erasing at 0x2080000 --  73% complete.
Erasing at 0x20c0000 --  74% complete.
Erasing at 0x2100000 --  75% complete.
Erasing at 0x2140000 --  76% complete.
Erasing at 0x2160000 --  77% complete.
Erasing at 0x21a0000 --  78% complete.
Erasing at 0x21e0000 --  79% complete.
Erasing at 0x2220000 --  80% complete.
Erasing at 0x2260000 --  81% complete.
Erasing at 0x22a0000 --  82% complete.
Erasing at 0x22e0000 --  83% complete.
Erasing at 0x2320000 --  84% complete.
Erasing at 0x2340000 --  85% complete.
Erasing at 0x2380000 --  86% complete.
Erasing at 0x23c0000 --  87% complete.
Erasing at 0x2400000 --  88% complete.
Erasing at 0x2440000 --  89% complete.
Erasing at 0x2480000 --  90% complete.
Erasing at 0x24c0000 --  91% complete.
Erasing at 0x2500000 --  92% complete.
Erasing at 0x2520000 --  93% complete.
Erasing at 0x2560000 --  94% complete.
Erasing at 0x25a0000 --  95% complete.
Erasing at 0x25e0000 --  96% complete.
Erasing at 0x2620000 --  97% complete.
Erasing at 0x2660000 --  98% complete.
Erasing at 0x26a0000 --  99% complete.
Erasing at 0x26c0000 -- 100% complete.
OK

NAND write: device 0 offset 0xf80000, size 0x17438ff
 24510464 bytes written: OK
(IPQ) # run flashimg2


Using eth1 device
TFTP from server 192.168.1.7; our IP address is 192.168.1.1
Filename 'EA8500-factory-to-ddwrt.img'.
Load address: 0x42000000
Loading: #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #####################################
done
Bytes transferred = 24393983 (17438ff hex)

NAND erase: device 0 offset 0x3780000, size 0x17438ff

Erasing at 0x3780000 --   0% complete.
Erasing at 0x37a0000 --   1% complete.
Erasing at 0x37e0000 --   2% complete.
Erasing at 0x3820000 --   3% complete.
Erasing at 0x3860000 --   4% complete.
Erasing at 0x38a0000 --   5% complete.
Erasing at 0x38e0000 --   6% complete.
Erasing at 0x3920000 --   7% complete.
Erasing at 0x3940000 --   8% complete.
Erasing at 0x3980000 --   9% complete.
Erasing at 0x39c0000 --  10% complete.
Erasing at 0x3a00000 --  11% complete.
Erasing at 0x3a40000 --  12% complete.
Erasing at 0x3a80000 --  13% complete.
Erasing at 0x3ac0000 --  14% complete.
Erasing at 0x3b00000 --  15% complete.
Erasing at 0x3b20000 --  16% complete.
Erasing at 0x3b60000 --  17% complete.
Erasing at 0x3ba0000 --  18% complete.
Erasing at 0x3be0000 --  19% complete.
Erasing at 0x3c20000 --  20% complete.
Erasing at 0x3c60000 --  21% complete.
Erasing at 0x3ca0000 --  22% complete.
Erasing at 0x3ce0000 --  23% complete.
Erasing at 0x3d00000 --  24% complete.
Erasing at 0x3d40000 --  25% complete.
Erasing at 0x3d80000 --  26% complete.
Erasing at 0x3dc0000 --  27% complete.
Erasing at 0x3e00000 --  28% complete.
Erasing at 0x3e40000 --  29% complete.
Erasing at 0x3e80000 --  30% complete.
Erasing at 0x3ea0000 --  31% complete.
Erasing at 0x3ee0000 --  32% complete.
Erasing at 0x3f20000 --  33% complete.
Erasing at 0x3f60000 --  34% complete.
Erasing at 0x3fa0000 --  35% complete.
Erasing at 0x3fe0000 --  36% complete.
Erasing at 0x4020000 --  37% complete.
Erasing at 0x4060000 --  38% complete.
Erasing at 0x4080000 --  39% complete.
Erasing at 0x40c0000 --  40% complete.
Erasing at 0x4100000 --  41% complete.
Erasing at 0x4140000 --  42% complete.
Erasing at 0x4180000 --  43% complete.
Erasing at 0x41c0000 --  44% complete.
Erasing at 0x4200000 --  45% complete.
Erasing at 0x4240000 --  46% complete.
Erasing at 0x4260000 --  47% complete.
Erasing at 0x42a0000 --  48% complete.
Erasing at 0x42e0000 --  49% complete.
Erasing at 0x4320000 --  50% complete.
Erasing at 0x4360000 --  51% complete.
Erasing at 0x43a0000 --  52% complete.
Erasing at 0x43e0000 --  53% complete.
Erasing at 0x4400000 --  54% complete.
Erasing at 0x4440000 --  55% complete.
Erasing at 0x4480000 --  56% complete.
Erasing at 0x44c0000 --  57% complete.
Erasing at 0x4500000 --  58% complete.
Erasing at 0x4540000 --  59% complete.
Erasing at 0x4580000 --  60% complete.
Erasing at 0x45c0000 --  61% complete.
Erasing at 0x45e0000 --  62% complete.
Erasing at 0x4620000 --  63% complete.
Erasing at 0x4660000 --  64% complete.
Erasing at 0x46a0000 --  65% complete.
Erasing at 0x46e0000 --  66% complete.
Erasing at 0x4720000 --  67% complete.
Erasing at 0x4760000 --  68% complete.
Erasing at 0x47a0000 --  69% complete.
Erasing at 0x47c0000 --  70% complete.
Erasing at 0x4800000 --  71% complete.
Erasing at 0x4840000 --  72% complete.
Erasing at 0x4880000 --  73% complete.
Erasing at 0x48c0000 --  74% complete.
Erasing at 0x4900000 --  75% complete.
Erasing at 0x4940000 --  76% complete.
Erasing at 0x4960000 --  77% complete.
Erasing at 0x49a0000 --  78% complete.
Erasing at 0x49e0000 --  79% complete.
Erasing at 0x4a20000 --  80% complete.
Erasing at 0x4a60000 --  81% complete.
Erasing at 0x4aa0000 --  82% complete.
Erasing at 0x4ae0000 --  83% complete.
Erasing at 0x4b20000 --  84% complete.
Erasing at 0x4b40000 --  85% complete.
Erasing at 0x4b80000 --  86% complete.
Erasing at 0x4bc0000 --  87% complete.
Erasing at 0x4c00000 --  88% complete.
Erasing at 0x4c40000 --  89% complete.
Erasing at 0x4c80000 --  90% complete.
Erasing at 0x4cc0000 --  91% complete.
Erasing at 0x4d00000 --  92% complete.
Erasing at 0x4d20000 --  93% complete.
Erasing at 0x4d60000 --  94% complete.
Erasing at 0x4da0000 --  95% complete.
Erasing at 0x4de0000 --  96% complete.
Erasing at 0x4e20000 --  97% complete.
Erasing at 0x4e60000 --  98% complete.
Erasing at 0x4ea0000 --  99% complete.
Erasing at 0x4ec0000 -- 100% complete.
OK

NAND write: device 0 offset 0x3780000, size 0x17438ff
 24510464 bytes written: OK
(IPQ) # reset


resetting ...

Resetting with watch dog!


U-Boot .07 [Standard IPQ806X.LN,r40331] (Apr 24 2015 - 09:08:25)

CBT U-Boot ver: 1.0.10

smem ram ptable found: ver: 0 len: 5
DRAM:  491 MiB
NAND:  SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:   
PCI0 Link Intialized
PCI1 Link Intialized
In:    serial
Out:   serial
Err:   serial
cdp: get part failed for 0:HLOS
Net:   MAC1 addr:0:3:7f:ba:db:1
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init  done
MAC2 addr:0:3:7f:ba:db:2
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         00:03:7f:ba:db:01
Address in environment is  00:06:3b:01:41:00
, eth1

Updating boot_count ... done

Hit any key to stop autoboot:  0 
MMC Device 0 not found
MMC Device 0 not found

Loading from nand0, offset 0x3780000
   Image Name:   Linux-3.18
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2097023 Bytes = 2 MiB
   Load Address: 42208000
   Entry Point:  42208000
Automatic boot of image at addr 0x44000000 ...
   Image Name:   Linux-3.18
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2097023 Bytes = 2 MiB
   Load Address: 42208000
   Entry Point:  42208000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
mtdids not defined, no default present
info: "mtdparts" not set
Using machid 0x1260 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.18.48 (bluebat@opensuse.site) (gcc version 6.3.0 (LEDE GCC 6.3.0 r2695-c9c68c7) ) #88 SMP PREEMPT Sun Mar 26 18:58:05 CEST 2017
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: Linksys EA8500 WiFi Router
[    0.000000] Ignoring memory range 0x41500000 - 0x42000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] PERCPU: Embedded 9 pages/cpu @ddfd3000 s7552 r8192 d21120 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 121920
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:16
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 481288K/491520K available (3878K kernel code, 282K rwdata, 1108K rodata, 188K init, 308K bss, 10232K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
[    0.000000]     vmalloc : 0xde800000 - 0xff000000   ( 520 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xde000000   ( 480 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0208000 - 0xc06e6e1c   (4988 kB)
[    0.000000]       .init : 0xc06e7000 - 0xc0716000   ( 188 kB)
[    0.000000]       .data : 0xc0716000 - 0xc075c9c4   ( 283 kB)
[    0.000000]        .bss : 0xc075c9c4 - 0xc07a9b84   ( 309 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000011] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 687194767200ns
[    0.000028] Switching to timer-based delay loop, resolution 160ns
[    0.000430] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000453] pid_max: default: 32768 minimum: 301
[    0.000707] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000724] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001363] CPU: Testing write buffer coherency: ok
[    0.001630] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.002124] Setting up static identity map for 0x42213180 - 0x422131d8
[    0.063435] CPU1: Booted secondary processor
[    0.063564] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.063685] Brought up 2 CPUs
[    0.063705] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.063716] CPU: All CPU(s) started in SVC mode.
[    0.078340] VFP support v0.3: implementor 51 architecture 0 part 4d variant 2 rev 0
[    0.078863] pinctrl core: initialized pinctrl subsystem
[    0.089387] NET: Registered protocol family 16
[    0.089713] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.113855] cpuidle: using governor ladder
[    0.144868] cpuidle: using governor menu
[    0.164080] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[    0.164164] qcom_rpm 108000.rpm: failed to mark ack irq as wakeup
[    0.164224] qcom_rpm 108000.rpm: failed to mark wakeup irq as wakeup
[    0.199471] pps_core: LinuxPPS API ver. 1 registered
[    0.199483] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.199527] PTP clock support registered
[    0.200640] pcie_init: pcie_init: unable to create IPC log context for pcie0-short
[    0.200653] pcie_init: pcie_init: unable to create IPC log context for pcie0-long
[    0.200663] pcie_init: pcie_init: unable to create IPC log context for pcie1-short
[    0.200672] pcie_init: pcie_init: unable to create IPC log context for pcie1-long
[    0.201069] Switched to clocksource dg_timer
[    0.202423] NET: Registered protocol family 2
[    0.203130] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.203167] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.203219] TCP: Hash tables configured (established 4096 bind 4096)
[    0.203265] TCP: reno registered
[    0.203285] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.203306] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.203538] NET: Registered protocol family 1
[    0.204713] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.204814] Crashlog allocated RAM at address 0x5ff00000
[    0.205761] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.205792] msgmni has been set to 940
[    0.207601] io scheduler noop registered
[    0.207621] io scheduler deadline registered (default)
[    0.208973] 1b500000.pci supply vdda not found, using dummy regulator
[    0.209061] 1b500000.pci supply vdda_phy not found, using dummy regulator
[    0.209138] 1b500000.pci supply vdda_refclk not found, using dummy regulator
[    0.240103] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.240126] pci_bus 0000:00: root bus resource [io  0xfe00000-0xfffff] (bus address [0x1fc00000-0xfefffff])
[    0.240140] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.240155] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.240664] PCI: bus0: Fast back to back transfers disabled
[    0.242658] PCI: bus1: Fast back to back transfers disabled
[    0.242827] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.242850] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.242962] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.242982] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.243772] 1b700000.pci supply vdda not found, using dummy regulator
[    0.243853] 1b700000.pci supply vdda_phy not found, using dummy regulator
[    0.243941] 1b700000.pci supply vdda_refclk not found, using dummy regulator
[    0.274166] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.274186] pci_bus 0001:00: root bus resource [io  0x31e10000-0xfffff] (bus address [0x63c00000-0x31eeffff])
[    0.274200] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.274214] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.274693] PCI: bus0: Fast back to back transfers disabled
[    0.276573] PCI: bus1: Fast back to back transfers disabled
[    0.276807] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.276828] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.276934] pci 0001:00:00.0: PCI bridge to [bus 01]
[    0.276951] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.277681] 1b900000.pci supply vdda not found, using dummy regulator
[    0.277759] 1b900000.pci supply vdda_phy not found, using dummy regulator
[    0.277836] 1b900000.pci supply vdda_refclk not found, using dummy regulator
[    0.412620] qcom-pcie 1b900000.pci: link initialization failed
[    0.414727] qcom-pcie 1b900000.pci: PCI host bridge to bus 0002:00
[    0.414744] pci_bus 0002:00: root bus resource [io  0x35e20000-0xfffff] (bus address [0x6bc00000-0x35edffff])
[    0.414758] pci_bus 0002:00: root bus resource [mem 0x32000000-0x35dfffff]
[    0.414778] pci_bus 0002:00: root bus resource [bus 00-ff]
[    0.414827] PCI: bus0: Fast back to back transfers enabled
[    0.417341] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.418679] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.419682] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.419779] msm_serial 16340000.serial: uartclk = 1843200
[    0.419836] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 184, base_baud = 115200) is a MSM
[    0.419892] msm_serial: console setup on port #0
[    1.133068] console [ttyMSM0] enabled
[    1.137847] msm_serial: driver initialized
[    1.144673] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[    1.145119] nand: AMD/Spansion S34MS01G2
[    1.151694] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    1.155540] Scanning device for bad blocks
[    1.586640] random: nonblocking pool is initialized
[    1.894315] 19 ofpart partitions found on MTD device qcom-nandc
[    1.894341] Creating 19 MTD partitions on "qcom-nandc":
[    1.899039] 0x000000000000-0x000000040000 : "SBL1"
[    1.905243] 0x000000040000-0x000000180000 : "MIBIB"
[    1.909897] 0x000000180000-0x0000002c0000 : "SBL2"
[    1.914713] 0x0000002c0000-0x000000540000 : "SBL3"
[    1.919496] 0x000000540000-0x000000660000 : "DDRCONFIG"
[    1.924356] 0x000000660000-0x000000780000 : "SSD"
[    1.929404] 0x000000780000-0x000000a00000 : "TZ"
[    1.934352] 0x000000a00000-0x000000c80000 : "RPM"
[    1.938982] 0x000000c80000-0x000000dc0000 : "art"
[    1.943626] 0x000000dc0000-0x000000ec0000 : "APPSBL"
[    1.948261] 0x000000ec0000-0x000000f00000 : "u_env"
[    1.953405] 0x000000f00000-0x000000f40000 : "s_env"
[    1.957909] 0x000000f40000-0x000000f80000 : "devinfo"
[    1.962812] 0x000000f80000-0x000003780000 : "linux"
[    1.967997] 0x000001280000-0x000003780000 : "rootfs"
[    1.972752] mtd: partition "rootfs" set to be root filesystem
[    1.977082] 0x000003780000-0x000005f40000 : "linux2"
[    1.983600] 0x000003a80000-0x000005f40000 : "rootfs2"
[    1.988584] 0x000005f40000-0x000005f80000 : "nvram"
[    1.993553] 0x000005f80000-0x000008000000 : "ddwrt"
[    1.999477] IMQ: autocreate imq0  NS c0756c80
[    2.002882] IMQ: autocreate imq1  NS c0756c80
[    2.006767] IMQ driver loaded successfully. (numdevs = 16, numqueues = 1)
[    2.011100] 	Hooking IMQ after NAT on PREROUTING.
[    2.017943] 	Hooking IMQ before NAT on POSTROUTING.
[    2.022947] libphy: Fixed MDIO Bus: probed
[    2.027671] libphy: GPIO Bitbanged MDIO: probed
[    2.052732] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[    2.827012] tun: Universal TUN/TAP device driver, 1.6
[    2.827037] tun: (C) 1999-2004 Max Krasnyansky 
[    2.832555] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.837112]  Ring mode enabled
[    2.842326]  DMA HW capability register supported
[    2.845186]  Enhanced/Alternate descriptors
[    2.849958] 	Enabled extended descriptors
[    2.854023]  RX Checksum Offload Engine supported (type 2)
[    2.858119]  TX Checksum insertion supported
[    2.863579]  Wake-Up On Lan supported
[    2.867988]  Enable RX Mitigation via HW Watchdog Timer
[    2.872796] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.876522]  Ring mode enabled
[    2.881806]  DMA HW capability register supported
[    2.884682]  Enhanced/Alternate descriptors
[    2.889455] 	Enabled extended descriptors
[    2.893508]  RX Checksum Offload Engine supported (type 2)
[    2.897616]  TX Checksum insertion supported
[    2.903067]  Wake-Up On Lan supported
[    2.907480]  Enable RX Mitigation via HW Watchdog Timer
[    2.911754] PPP generic driver version 2.4.2
[    2.916176] PPP BSD Compression module registered
[    2.920545] PPP Deflate Compression module registered
[    2.925260] PPP MPPE Compression module registered
[    2.930190] NET: Registered protocol family 24
[    2.934977] PPTP driver version 0.8.5
[    2.939420] i2c /dev entries driver
[    2.948641] Speed bin: 0
[    2.948663] PVS bin: 1
[    2.950643] platform cpufreq-krait.0: Driver cpufreq-krait requests probe deferral
[    2.954408] L2 @ QSB rate. Forcing new rate.
[    2.960194] L2 @ 387500 KHz
[    2.964590] CPU0 @ 800000 KHz
[    2.966902] CPU1 @ QSB rate. Forcing new rate.
[    2.970109] CPU1 @ 384000 KHz
[    2.974742] GACT probability NOT on
[    2.977421] Mirror/redirect action on
[    2.980744] Simple TC action Loaded
[    2.985462] netem: version 1.3
[    2.987883] u32 classifier
[    2.990943]     Performance counters on
[    2.993729]     input device check on
[    2.997369]     Actions configured
[    3.001243] Netfilter messages via NETLINK v0.30.
[    3.004635] nf_conntrack version 0.5.0 (7520 buckets, 30080 max)
[    3.009614] nf_conntrack_rtsp v0.7 loading
[    3.016035] xt_time: kernel timezone is -0000
[    3.019278] ip_set: protocol 6
[    3.024034] gre: GRE over IPv4 demultiplexor driver
[    3.026859] nf_nat_rtsp v0.7 loading
[    3.031546] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.035453] TCP: bic registered
[    3.040521] TCP: cubic registered
[    3.043478] TCP: westwood registered
[    3.046856] TCP: highspeed registered
[    3.050502] TCP: hybla registered
[    3.054215] TCP: htcp registered
[    3.057362] TCP: vegas registered
[    3.060659] TCP: veno registered
[    3.063965] TCP: scalable registered
[    3.067170] TCP: lp registered
[    3.070728] TCP: yeah registered
[    3.073678] TCP: illinois registered
[    3.076984] NET: Registered protocol family 17
[    3.080614] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    3.084927] Bridge firewalling registered
[    3.097642] 8021q: 802.1Q VLAN Support v1.8
[    3.101680] Registering SWP/SWPB emulation handler
[    3.109313] trying to register driver generic_krait
[    3.110322] Frequency table not initialized.
[    3.115284] Frequency table not initialized.
[    3.119631] Frequency table not initialized.
[    3.123937] Frequency table not initialized.
[    3.128100] Frequency table not initialized.
[    3.133952] Frequency table not initialized.
[    3.136671] Frequency table not initialized.
[    3.140876] Frequency table not initialized.
[    3.145176] Frequency table not initialized.
[    3.149365] Frequency table not initialized.
[    3.153709] driver generic_krait up and running
[    3.157922] searching for nvram
[    3.162221] nvram size = -1066954702
[    3.184377] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    3.192082] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    3.196874] VFS: Mounted root (squashfs filesystem) readonly on device 31:16.
[    3.198676] Freeing unused kernel memory: 188K (c06e7000 - c0716000)
start service
starting Architecture code for ipq806x
cannot open /dev/nvram
udevtrigger[52]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
sysinit using mac C0:56:27:24:21:61
[    5.476290] UBIFS error (pid 712): ubifs_mount: cannot open "ubi0:rootfs_data", error -19
mount: mounting ubi0:rootfs_data on /jffs failed: No such device
reset boot counter
load ATH 802.11 a/b/g Driver
insmod: ath_pci.ko: module not found
insmod: ath_ahb.ko: module not found
load ATH9K 802.11n Driver
[    6.726858] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[    6.726894] Backport generated by backports.git backports-20160324-13-g24da7d3c
load ATH/QCA 802.11ac Driver
[    7.194589] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[    7.195240] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    7.323470] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[    7.323508] ath10k_pci 0000:01:00.0: Falling back to user helper
[    7.625946] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[    7.625984] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[    7.636055] ath10k_pci 0000:01:00.0: firmware ver 10.4.3.00063 api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce
[    7.646212] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
[    7.652849] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 c74d566b
[    8.512580] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[    8.623939] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[    8.843430] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1
[    8.916507] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[    8.917162] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    9.062625] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
[    9.062664] ath10k_pci 0001:01:00.0: Falling back to user helper
[    9.074453] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[    9.078395] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0
[    9.092809] ath10k_pci 0001:01:00.0: firmware ver 10.4.3.00063 api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce
[    9.096167] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
[    9.106458] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 5bd10948
[   10.297863] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1
[USB] checking...
umount: can't unmount /mnt: No such file or directory
/etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
[   12.294732] expr wrote to tcp_keepalive_time when file position was not 0!
[   12.294732] This will not be supported in the future. To silence this
[   12.294732] warning, set kernel.sysctl_writes_strict = -1
cannot open /proc/sys/net/ipv4/ip_conntrack_max
/etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
ath9k deconfigure_single: phy0 ath0
interface wlan0 does not exist!
ath9k deconfigure_single: phy1 ath1
interface wlan1 does not exist!
ifconfig: invalid hw-addr 
[   13.029375] device br0 entered promiscuous mode
killall: ead: no process killed
[   13.089392] device vlan1 entered promiscuous mode
[   13.089420] device eth0 entered promiscuous mode
sh: ead: not found
[   13.098362] br0: port 1(vlan1) entered forwarding state
[   13.099424] br0: port 1(vlan1) entered forwarding state
[   13.104549] device br0 left promiscuous mode
[   13.112662] device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Address not available
[   13.124543] device br0 left promiscuous mode
ath9k deconfigure_single: phy0 ath0
ath9k deconfigure_single: phy1 ath1
[   15.092421] br0: port 1(vlan1) entered forwarding state
ath9k configure_single: phy0 ath0
sh: can't create /sys/kernel/debug/ieee80211/phy0/ath9k/chanbw: nonexistent directory
call mac80211autochannel for interface: ath0
freq:2412 qual:94 noise:-100 eirp: 30
freq:2452 qual:93 noise:-96 eirp: 30
freq:2432 qual:86 noise:-97 eirp: 30
freq:2422 qual:67 noise:-98 eirp: 30
freq:2442 qual:63 noise:-97 eirp: 30
freq:2462 qual:63 noise:-97 eirp: 30
freq:2417 qual:46 noise:-97 eirp: 30
freq:2427 qual:44 noise:-96 eirp: 30
freq:2447 qual:44 noise:-97 eirp: 30
freq:2457 qual:39 noise:-97 eirp: 30
freq:2437 qual:35 noise:-97 eirp: 30
mac80211autochannel interface: ath0 frequency: 2412
setup ath0 C0:56:27:24:21:63
Configuration file: /tmp/ath0_hostap.conf
ath0: interface state UNINITIALIZED->COUNTRY_UPDATE
Using interface ath0 with hwaddr c0:56:27:24:21:63 and ssid "dd-wrt"
ath0: interface state COUNTRY_UPDATE->ENABLED
ath0: AP-ENABLED 
[   24.203937] device ath0 entered promiscuous mode
[   24.204353] br0: port 2(ath0) entered forwarding state
[   24.207681] br0: port 2(ath0) entered forwarding state
ath9k configure_single: phy1 ath1
sh: can't create /sys/kernel/debug/ieee80211/phy1/ath9k/chanbw: nonexistent directory
call mac80211autochannel for interface: ath1
[   26.205277] br0: port 2(ath0) entered forwarding state
freq:5745 qual:99 noise:-103 eirp: 30
freq:5765 qual:99 noise:-103 eirp: 30
freq:5785 qual:99 noise:-103 eirp: 30
freq:5805 qual:99 noise:-103 eirp: 30
freq:5825 qual:99 noise:-103 eirp: 30
freq:5180 qual:93 noise:-104 eirp: 23
freq:5200 qual:93 noise:-104 eirp: 23
freq:5220 qual:93 noise:-104 eirp: 23
freq:5240 qual:93 noise:-104 eirp: 23
freq:5260 qual:93 noise:-104 eirp: 23
freq:5280 qual:93 noise:-104 eirp: 23
freq:5300 qual:93 noise:-104 eirp: 23
freq:5320 qual:93 noise:-104 eirp: 23
freq:5580 qual:93 noise:-104 eirp: 23
freq:5600 qual:93 noise:-104 eirp: 23
freq:5620 qual:93 noise:-104 eirp: 23
freq:5640 qual:93 noise:-104 eirp: 23
freq:5500 qual:92 noise:-103 eirp: 23
freq:5520 qual:92 noise:-103 eirp: 23
freq:5540 qual:92 noise:-103 eirp: 23
freq:5560 qual:92 noise:-103 eirp: 23
freq:5660 qual:92 noise:-103 eirp: 23
freq:5680 qual:92 noise:-103 eirp: 23
freq:5700 qual:92 noise:-103 eirp: 23
freq:5720 qual:92 noise:-103 eirp: 23
mac80211autochannel interface: ath1 frequency: 5745
setup ath1 C0:56:27:24:21:64
Configuration file: /tmp/ath1_hostap.conf
ath1: interface state UNINITIALIZED->COUNTRY_UPDATE
Using interface ath1 with hwaddr c0:56:27:24:21:64 and ssid "dd-wrt"
ath1: interface state COUNTRY_UPDATE->ENABLED
ath1: AP-ENABLED 
[   36.328390] device ath1 entered promiscuous mode
[   36.328990] br0: port 3(ath1) entered forwarding state
[   36.332244] br0: port 3(ath1) entered forwarding state
killall: roaming_daemon: no process killed
sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max: nonexistent directory
sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max_hyst: nonexistent directory
sh: stop: out of range
cp: can't stat '/tmp/mycron.d/*': No such file or directory
cp: can't stat '/jffs/mycron.d/*': No such file or directory
cp: can't stat '/mmc/mycron.d/*': No such file or directory
[   36.723320] device vlan2 entered promiscuous mode
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
cat: can't open '/proc/sys/net/netfilter/nf_conntrack_flush': No such file or directory
[   37.186940] device vlan2 left promiscuous mode
udhcpc: started, v1.26.2
cat: can't open '/proc/sys/net/netfilter/nf_conntrack_flush': No such file or directory
ath9k radio 0: phy0 ath0
ath9k radio 0: phy1 ath1
cannot open /proc/sys/dev/wifi0/silent
cannot open /proc/sys/dev/wifi0/ledon
cannot open /proc/sys/dev/wifi1/silent
cannot open /proc/sys/dev/wifi1/ledon
ath9k radio 1: phy0 ath0
ath9k radio 1: phy1 ath1
cannot open /proc/sys/dev/wifi0/silent
cannot open /proc/sys/dev/wifi1/silent
udhcpc: sending discover
/opt/etc/init.d/rcS: No such file or directory
/jffs/etc/init.d/rcS: No such file or directory
/mmc/etc/init.d/rcS: No such file or directory
sh: missing ]
killall: proxywatchdog.sh: no process killed
The Milkfish Router Services
ERROR: Necessary service setting not found: milkfish_username - aborting.
/mnt/smbshare
umount: can't unmount /mnt/smbshare: No such file or directory
rmmod: cifs: No such file or directory
rmmod: fscache: No such file or directory
The Milkfish Router Services
Restoring SIP ddsubscriber database from NVRAM...
killall: schedulerb.sh: no process killed
Empty.
The Milkfish Router Services
Restoring SIP ddaliases database from NVRAM...
killall: shatd: no process killed
Empty.
killall: wdswatchdog.sh: no process killed
[   38.338324] br0: port 3(ath1) entered forwarding state
udhcpc: sending discover
udhcpc: sending discover

DD-WRT v3.0-r31780M kongat (c) 2017 NewMedia-NET GmbH
Release: 03/26/17

DD-WRT login: