# dd-wrt forum post ---> https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1169770#1169770
mrjcd@Deb:~$ telnet 192.168.1.1
Trying 192.168.1.1...
Connected to 192.168.1.1.
Escape character is '^]'.
DD-WRT v3.0-r27506 std (c) 2015 NewMedia-NET GmbH
Release: 07/09/15
DD-WRT login: root
Password:
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
http://www.dd-wrt.com
==========================================================
BusyBox v1.23.2 (2015-07-09 01:55:43 CEST) built-in shell (ash)
root@DD-WRT:~# nvram get DD_BOARD
Linksys WRT160NL
root@DD-WRT:~# erase linux
erase[7995392]
root@DD-WRT:~# reboot
root@DD-WRT:~# Connection closed by foreign host.
mrjcd@Deb:~$ tftp 192.168.1.1
tftp> mode binary
tftp> rexmt 1
tftp> timeout 60
tftp> put wrt160nl-firmware.bin
Sent 7734272 bytes in 2.6 seconds
tftp> q
# you guys just let her sit for about 2~3 minutes and then do a power cycle and she will come up just fine
mrjcd@Deb:~$ telnet 192.168.1.1
Trying 192.168.1.1...
Connected to 192.168.1.1.
Escape character is '^]'.
DD-WRT v3.0-r40189 std (c) 2019 NewMedia-NET GmbH
Release: 07/04/19
Board: Linksys WRT160NL
DD-WRT login: root
Password:
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
http://www.dd-wrt.com
==========================================================
BusyBox v1.31.0 (2019-07-04 04:12:20 CEST) built-in shell (ash)
root@DD-WRT:~# dmesg
<5>[ 0.000000] Linux version 3.10.108-d8 (root@linux) (gcc version 9.1.0 (OpenWrt GCC 9.1.0 r10178+1-0e1d07af1d) ) #13639 Thu Jul 4 04:11:51 CEST 2019
<4>[ 0.000000] flash_size passed from bootloader = 8
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
<6>[ 0.000000] booting platform Atheros AR9130 rev 2 (0xb8)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 02000000 @ 00000000 (usable)
<4>[ 0.000000] Zone ranges:
<4>[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
<4>[ 0.000000] Movable zone start for each node
<4>[ 0.000000] Early memory node ranges
<4>[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
<7>[ 0.000000] On node 0 totalpages: 8192
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802f6f80, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 64 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
<4>[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<6>[ 0.000000] Memory: 28968k/32768k available (2330k kernel code, 3800k reserved, 401k data, 208k init, 0k highmem)
<6>[ 0.000000] NR_IRQS:83
<0>[ 0.000000] irq init done
<4>[ 0.000000] plat_time_init: plat time init done
<6>[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
<6>[ 0.080000] pid_max: default: 32768 minimum: 301
<6>[ 0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<4>[ 0.100000] Can't analyze schedule() prologue at 80066e08
<6>[ 0.120000] bio: create slab <bio-0> at 0
<5>[ 0.130000] SCSI subsystem initialized
<6>[ 0.130000] usbcore: registered new interface driver usbfs
<6>[ 0.140000] usbcore: registered new interface driver hub
<6>[ 0.140000] usbcore: registered new device driver usb
<6>[ 0.150000] Switching to clocksource MIPS
<6>[ 0.150000] NET: Registered protocol family 2
<6>[ 0.160000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
<6>[ 0.160000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
<6>[ 0.170000] TCP: Hash tables configured (established 512 bind 512)
<6>[ 0.170000] TCP: reno registered
<6>[ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.190000] NET: Registered protocol family 1
<5>[ 0.190000] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.200000] Register LED Device
<5>[ 0.200000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<4>[ 0.210000] AR7100 GPIOC major 0
<6>[ 0.220000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>[ 0.220000] msgmni has been set to 56
<6>[ 0.230000] io scheduler noop registered
<6>[ 0.230000] io scheduler deadline registered (default)
<6>[ 0.230000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.260000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
<6>[ 0.270000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.280000] guessed flashsize = 8M
<0>[ 0.290000] scanning for root partition
<0>[ 0.290000] WRT160NL/E2100L uboot detected
<0>[ 0.290000] bootloader size = 40000
<0>[ 0.300000]
<0>[ 0.300000] found squashfs at 192000
<5>[ 0.310000] Creating 8 MTD partitions on "ar7100-nor0":
<5>[ 0.310000] 0x000000000000-0x000000040000 : "RedBoot"
<5>[ 0.320000] 0x000000040000-0x0000007e0000 : "linux"
<5>[ 0.330000] 0x000000192000-0x000000790000 : "rootfs"
<4>[ 0.330000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>[ 0.350000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.350000] 0x000000790000-0x0000007e0000 : "ddwrt"
<5>[ 0.360000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.360000] 0x0000007f0000-0x000000800000 : "FIS directory"
<5>[ 0.370000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.380000] 0x000000000000-0x000000800000 : "fullflash"
<4>[ 0.390000] ->Oops: flash id 0xc22017 .
<6>[ 0.790000] PPP generic driver version 2.4.2
<6>[ 0.800000] PPP BSD Compression module registered
<6>[ 0.800000] PPP Deflate Compression module registered
<6>[ 0.800000] PPP MPPE Compression module registered
<6>[ 0.810000] NET: Registered protocol family 24
<6>[ 0.810000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 0.850000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 0.860000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<6>[ 0.900000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 0.920000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 0.920000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 0.930000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 0.940000] usb usb1: Product: Atheros AR91xx built-in EHCI controller
<6>[ 0.940000] usb usb1: Manufacturer: Linux 3.10.108-d8 ehci_hcd
<6>[ 0.950000] usb usb1: SerialNumber: platform
<6>[ 0.950000] hub 1-0:1.0: USB hub found
<6>[ 0.960000] hub 1-0:1.0: 1 port detected
<6>[ 0.970000] u32 classifier
<6>[ 0.970000] Performance counters on
<6>[ 0.980000] input device check on
<6>[ 0.980000] Actions configured
<6>[ 0.990000] Netfilter messages via NETLINK v0.30.
<6>[ 0.990000] nf_conntrack version 0.5.0 (452 buckets, 1808 max)
<4>[ 1.000000] nf_conntrack_rtsp v0.7 loading
<4>[ 1.000000] nf_nat_rtsp v0.7 loading
<6>[ 1.010000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 1.010000] TCP: westwood registered
<6>[ 1.010000] TCP: hybla registered
<6>[ 1.020000] TCP: vegas registered
<6>[ 1.020000] NET: Registered protocol family 17
<5>[ 1.030000] Bridge firewalling registered
<6>[ 1.030000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 1.040000] searching for nvram
<6>[ 1.040000] nvram size = 65536
<6>[ 1.070000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 1.080000] ar71xx-wdt: timeout=15 secs (max=21) ref freq=200000000
<6>[ 1.090000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 1.100000] Freeing unused kernel memory: 208K
<7>[ 4.070000] ar71xx-wdt: enabling watchdog timer
<6>[ 4.160000] libphy: ag71xx_mdio: probed
<6>[ 4.490000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
<6>[ 4.490000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=00008306, driver=Realtek RTL8306S]
<6>[ 4.500000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RMII
<6>[ 4.830000] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=00008306, driver=Realtek RTL8306S]
<6>[ 4.840000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RMII
<6>[ 5.000000] Loading modules backported from Linux version wireless-drivers-next-for-davem-2017-09-01-0-geb464d4a8d09
<6>[ 5.010000] Backport generated by backports.git backports-20160324-111-g97b8d7c4
<7>[ 5.850000] ath: EEPROM regdomain: 0x0
<7>[ 5.850000] ath: EEPROM indicates default country code should be used
<7>[ 5.850000] ath: doing EEPROM country->regdmn map search
<7>[ 5.850000] ath: country maps to regdmn code: 0x3a
<7>[ 5.850000] ath: Country alpha2 being used: US
<7>[ 5.850000] ath: Regpair used: 0x3a
<7>[ 5.890000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 5.890000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
<7>[ 6.490000] ar71xx: pll_reg 0xb8050014: 0x13000a44
<6>[ 6.490000] eth0: link up (100Mbps/Full duplex)
<6>[ 8.740000] device br0 entered promiscuous mode
<6>[ 8.790000] eth0: link down
<6>[ 8.840000] device eth0 entered promiscuous mode
<6>[ 8.850000] br0: port 1(eth0) entered forwarding state
<6>[ 8.860000] br0: port 1(eth0) entered forwarding state
<6>[ 8.860000] device br0 left promiscuous mode
<6>[ 8.870000] device br0 entered promiscuous mode
<6>[ 8.890000] device br0 left promiscuous mode
<7>[ 8.950000] ath: EEPROM regdomain: 0x8348
<7>[ 8.950000] ath: EEPROM indicates we should expect a country code
<7>[ 8.950000] ath: doing EEPROM country->regdmn map search
<7>[ 8.950000] ath: country maps to regdmn code: 0x3a
<7>[ 8.950000] ath: Country alpha2 being used: US
<7>[ 8.950000] ath: Regpair used: 0x3a
<7>[ 8.950000] ath: regdomain 0x8348 dynamically updated by user
<6>[ 9.740000] br0: port 1(eth0) entered disabled state
<7>[ 10.490000] ar71xx: pll_reg 0xb8050014: 0x13000a44
<6>[ 10.490000] eth0: link up (100Mbps/Full duplex)
<6>[ 10.490000] br0: port 1(eth0) entered forwarding state
<6>[ 10.500000] br0: port 1(eth0) entered forwarding state
<6>[ 16.650000] device ath0 entered promiscuous mode
<6>[ 16.650000] br0: port 2(ath0) entered forwarding state
<6>[ 16.660000] br0: port 2(ath0) entered forwarding state
<6>[ 17.320000] device eth1 entered promiscuous mode
<1>[ 17.400000] fast-classifier (PBR safe v2.1b): starting up
<1>[ 17.410000] fast-classifier: registered
<6>[ 18.480000] device eth1 left promiscuous mode
<6>[ 25.520000] br0: port 1(eth0) entered forwarding state
<6>[ 31.680000] br0: port 2(ath0) entered forwarding state
root@DD-WRT:~# exit
Connection closed by foreign host.
mrjcd@Deb:~$