mrjcd@Deb:~$ ssh root@160nl-switch.mrjcd.com
DD-WRT v3.0-r40260 std (c) 2019 NewMedia-NET GmbH
Release: 07/09/19
Board: Linksys WRT160NL
root@160nl-switch.mrjcd.com's password:
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
http://www.dd-wrt.com
==========================================================
BusyBox v1.31.0 (2019-07-09 02:58:32 CEST) built-in shell (ash)
root@160nl-switch:~# dmesg
<5>[ 0.000000] Linux version 3.10.108-d8 (root@linux) (gcc version 9.1.0 (OpenWrt GCC 9.1.0 r10178+1-0e1d07af1d) ) #14348 Tue Jul 9 02:58:05 CEST 2019
<4>[ 0.000000] flash_size passed from bootloader = 8
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
<6>[ 0.000000] booting platform Atheros AR9130 rev 2 (0xb8)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 02000000 @ 00000000 (usable)
<4>[ 0.000000] Zone ranges:
<4>[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
<4>[ 0.000000] Movable zone start for each node
<4>[ 0.000000] Early memory node ranges
<4>[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
<7>[ 0.000000] On node 0 totalpages: 8192
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802f6f80, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 64 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
<4>[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<6>[ 0.000000] Memory: 28968k/32768k available (2330k kernel code, 3800k reserved, 401k data, 208k init, 0k highmem)
<6>[ 0.000000] NR_IRQS:83
<0>[ 0.000000] irq init done
<4>[ 0.000000] plat_time_init: plat time init done
<6>[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
<6>[ 0.080000] pid_max: default: 32768 minimum: 301
<6>[ 0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<4>[ 0.100000] Can't analyze schedule() prologue at 80066e08
<6>[ 0.120000] bio: create slab <bio-0> at 0
<5>[ 0.130000] SCSI subsystem initialized
<6>[ 0.130000] usbcore: registered new interface driver usbfs
<6>[ 0.140000] usbcore: registered new interface driver hub
<6>[ 0.140000] usbcore: registered new device driver usb
<6>[ 0.150000] Switching to clocksource MIPS
<6>[ 0.150000] NET: Registered protocol family 2
<6>[ 0.160000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
<6>[ 0.160000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
<6>[ 0.170000] TCP: Hash tables configured (established 512 bind 512)
<6>[ 0.170000] TCP: reno registered
<6>[ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.190000] NET: Registered protocol family 1
<5>[ 0.190000] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.200000] Register LED Device
<5>[ 0.200000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<4>[ 0.210000] AR7100 GPIOC major 0
<6>[ 0.220000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>[ 0.220000] msgmni has been set to 56
<6>[ 0.230000] io scheduler noop registered
<6>[ 0.230000] io scheduler deadline registered (default)
<6>[ 0.230000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.260000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
<6>[ 0.270000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.280000] guessed flashsize = 8M
<0>[ 0.290000] scanning for root partition
<0>[ 0.290000] WRT160NL/E2100L uboot detected
<0>[ 0.290000] bootloader size = 40000
<0>[ 0.300000]
<0>[ 0.300000] found squashfs at 192000
<5>[ 0.310000] Creating 8 MTD partitions on "ar7100-nor0":
<5>[ 0.310000] 0x000000000000-0x000000040000 : "RedBoot"
<5>[ 0.320000] 0x000000040000-0x0000007e0000 : "linux"
<5>[ 0.330000] 0x000000192000-0x0000007a0000 : "rootfs"
<4>[ 0.330000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>[ 0.350000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.350000] 0x0000007a0000-0x0000007e0000 : "ddwrt"
<5>[ 0.360000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.360000] 0x0000007f0000-0x000000800000 : "FIS directory"
<5>[ 0.370000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.380000] 0x000000000000-0x000000800000 : "fullflash"
<4>[ 0.390000] ->Oops: flash id 0x1c2017 .
<6>[ 0.790000] PPP generic driver version 2.4.2
<6>[ 0.800000] PPP BSD Compression module registered
<6>[ 0.800000] PPP Deflate Compression module registered
<6>[ 0.800000] PPP MPPE Compression module registered
<6>[ 0.810000] NET: Registered protocol family 24
<6>[ 0.810000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 0.850000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 0.860000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<6>[ 0.900000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 0.920000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 0.920000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 0.930000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 0.940000] usb usb1: Product: Atheros AR91xx built-in EHCI controller
<6>[ 0.940000] usb usb1: Manufacturer: Linux 3.10.108-d8 ehci_hcd
<6>[ 0.950000] usb usb1: SerialNumber: platform
<6>[ 0.950000] hub 1-0:1.0: USB hub found
<6>[ 0.960000] hub 1-0:1.0: 1 port detected
<6>[ 0.970000] u32 classifier
<6>[ 0.970000] Performance counters on
<6>[ 0.980000] input device check on
<6>[ 0.980000] Actions configured
<6>[ 0.990000] Netfilter messages via NETLINK v0.30.
<6>[ 0.990000] nf_conntrack version 0.5.0 (452 buckets, 1808 max)
<4>[ 1.000000] nf_conntrack_rtsp v0.7 loading
<4>[ 1.000000] nf_nat_rtsp v0.7 loading
<6>[ 1.010000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 1.010000] TCP: westwood registered
<6>[ 1.010000] TCP: hybla registered
<6>[ 1.020000] TCP: vegas registered
<6>[ 1.020000] NET: Registered protocol family 17
<5>[ 1.030000] Bridge firewalling registered
<6>[ 1.030000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 1.040000] searching for nvram
<6>[ 1.040000] nvram size = 65536
<6>[ 1.070000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 1.080000] ar71xx-wdt: timeout=15 secs (max=21) ref freq=200000000
<6>[ 1.090000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 1.100000] Freeing unused kernel memory: 208K
<6>[ 1.330000] usb 1-1: new high-speed USB device number 2 using ar71xx-ehci
<6>[ 1.760000] usb 1-1: New USB device found, idVendor=058f, idProduct=6387
<6>[ 1.760000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 1.770000] usb 1-1: Product: Mass Storage
<6>[ 1.780000] usb 1-1: Manufacturer: Generic
<6>[ 1.780000] usb 1-1: SerialNumber: 1DF77398
<7>[ 4.640000] ar71xx-wdt: enabling watchdog timer
<6>[ 4.730000] libphy: ag71xx_mdio: probed
<6>[ 5.060000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
<6>[ 5.060000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=00008306, driver=Realtek RTL8306S]
<6>[ 5.070000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RMII
<6>[ 5.400000] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=00008306, driver=Realtek RTL8306S]
<6>[ 5.410000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RMII
<6>[ 5.590000] Loading modules backported from Linux version wireless-drivers-next-for-davem-2017-09-01-0-geb464d4a8d09
<6>[ 5.600000] Backport generated by backports.git backports-20160324-111-g97b8d7c4
<7>[ 6.450000] ath: EEPROM regdomain: 0x0
<7>[ 6.450000] ath: EEPROM indicates default country code should be used
<7>[ 6.450000] ath: doing EEPROM country->regdmn map search
<7>[ 6.450000] ath: country maps to regdmn code: 0x3a
<7>[ 6.450000] ath: Country alpha2 being used: US
<7>[ 6.450000] ath: Regpair used: 0x3a
<7>[ 6.490000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 6.500000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
<7>[ 7.070000] ar71xx: pll_reg 0xb8050014: 0x13000a44
<6>[ 7.070000] eth0: link up (100Mbps/Full duplex)
<6>[ 7.690000] usb-storage 1-1:1.0: USB Mass Storage device detected
<6>[ 7.700000] scsi0 : usb-storage 1-1:1.0
<6>[ 7.700000] usbcore: registered new interface driver usb-storage
<5>[ 8.700000] scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 4
<5>[ 8.710000] sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>[ 8.720000] sd 0:0:0:0: [sda] 31457280 512-byte logical blocks: (16.1 GB/15.0 GiB)
<5>[ 8.730000] sd 0:0:0:0: [sda] Write Protect is off
<7>[ 8.730000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
<5>[ 8.730000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
<6>[ 8.750000] sda: sda1
<5>[ 8.760000] sd 0:0:0:0: [sda] Attached SCSI removable disk
<6>[ 9.530000] device br0 entered promiscuous mode
<6>[ 9.570000] eth0: link down
<6>[ 9.670000] device eth0 entered promiscuous mode
<6>[ 9.680000] br0: port 1(eth0) entered forwarding state
<6>[ 9.680000] br0: port 1(eth0) entered forwarding state
<6>[ 9.840000] device eth1 entered promiscuous mode
<6>[ 9.860000] device br0 left promiscuous mode
<6>[ 9.870000] device br0 entered promiscuous mode
<6>[ 9.930000] device br0 left promiscuous mode
<7>[ 10.110000] ath: EEPROM regdomain: 0x8348
<7>[ 10.110000] ath: EEPROM indicates we should expect a country code
<7>[ 10.110000] ath: doing EEPROM country->regdmn map search
<7>[ 10.110000] ath: country maps to regdmn code: 0x3a
<7>[ 10.110000] ath: Country alpha2 being used: US
<7>[ 10.110000] ath: Regpair used: 0x3a
<7>[ 10.110000] ath: regdomain 0x8348 dynamically updated by user
<6>[ 10.380000] br0: port 1(eth0) entered disabled state
<4>[ 10.560000] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
<4>[ 10.570000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
<7>[ 11.070000] ar71xx: pll_reg 0xb8050014: 0x13000a44
<6>[ 11.070000] eth0: link up (100Mbps/Full duplex)
<6>[ 11.070000] br0: port 1(eth0) entered forwarding state
<6>[ 11.080000] br0: port 1(eth0) entered forwarding state
<6>[ 16.780000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<1>[ 17.770000] fast-classifier (PBR safe v2.1b): starting up
<1>[ 17.780000] fast-classifier: registered
<6>[ 26.120000] br0: port 1(eth0) entered forwarding state
root@160nl-switch:~# date
Wed Jul 10 13:11:33 CDT 2019
root@160nl-switch:~# exit
Connection to 160nl-switch.mrjcd.com closed.
mrjcd@Deb:~$ telnet 192.168.1.1
Trying 192.168.1.1...
Connected to 192.168.1.1.
Escape character is '^]'.
DD-WRT v3.0-r34311 std (c) 2017 NewMedia-NET GmbH
Release: 12/29/17
DD-WRT login: root
Password:
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
http://www.dd-wrt.com
==========================================================
BusyBox v1.27.2 (2017-12-29 02:31:23 CET) built-in shell (ash)
root@DD-WRT:~# nvram get DD_BOARD
Linksys WRT160NL
root@DD-WRT:~# dmesg
<5>[ 0.000000] Linux version 3.10.108 (root@linux) (gcc version 7.2.0 (LEDE GCC 7.2.0 r5086-aba071d818) ) #45960 Fri Dec 29 02:31:05 CET 2017
<4>[ 0.000000] flash_size passed from bootloader = 8
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
<6>[ 0.000000] booting platform Atheros AR9130 rev 2 (0xb8)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 02000000 @ 00000000 (usable)
<4>[ 0.000000] Zone ranges:
<4>[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
<4>[ 0.000000] Movable zone start for each node
<4>[ 0.000000] Early memory node ranges
<4>[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
<7>[ 0.000000] On node 0 totalpages: 8192
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802f8fc0, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 64 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
<4>[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<6>[ 0.000000] Memory: 28968k/32768k available (2345k kernel code, 3800k reserved, 395k data, 200k init, 0k highmem)
<6>[ 0.000000] NR_IRQS:83
<0>[ 0.000000] irq init done
<4>[ 0.000000] plat_time_init: plat time init done
<6>[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
<6>[ 0.080000] pid_max: default: 32768 minimum: 301
<6>[ 0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<4>[ 0.100000] Can't analyze schedule() prologue at 80066e20
<6>[ 0.120000] bio: create slab <bio-0> at 0
<5>[ 0.130000] SCSI subsystem initialized
<6>[ 0.130000] usbcore: registered new interface driver usbfs
<6>[ 0.140000] usbcore: registered new interface driver hub
<6>[ 0.140000] usbcore: registered new device driver usb
<6>[ 0.150000] Switching to clocksource MIPS
<6>[ 0.150000] NET: Registered protocol family 2
<6>[ 0.160000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
<6>[ 0.160000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
<6>[ 0.170000] TCP: Hash tables configured (established 512 bind 512)
<6>[ 0.170000] TCP: reno registered
<6>[ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.190000] NET: Registered protocol family 1
<5>[ 0.190000] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.200000] Register LED Device
<5>[ 0.200000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<4>[ 0.210000] AR7100 GPIOC major 0
<6>[ 0.210000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>[ 0.220000] msgmni has been set to 56
<6>[ 0.230000] io scheduler noop registered
<6>[ 0.230000] io scheduler deadline registered (default)
<6>[ 0.230000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.260000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
<6>[ 0.270000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.280000] guessed flashsize = 8M
<0>[ 0.290000] scanning for root partition
<0>[ 0.290000] WRT160NL/E2100L uboot detected
<0>[ 0.290000] bootloader size = 40000
<0>[ 0.300000]
<0>[ 0.300000] found squashfs at 193000
<5>[ 0.310000] Creating 8 MTD partitions on "ar7100-nor0":
<5>[ 0.310000] 0x000000000000-0x000000040000 : "RedBoot"
<5>[ 0.320000] 0x000000040000-0x0000007e0000 : "linux"
<5>[ 0.330000] 0x000000193000-0x0000007d0000 : "rootfs"
<4>[ 0.330000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>[ 0.350000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.350000] 0x0000007d0000-0x0000007e0000 : "ddwrt"
<5>[ 0.360000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.360000] 0x0000007f0000-0x000000800000 : "FIS directory"
<5>[ 0.370000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.380000] 0x000000000000-0x000000800000 : "fullflash"
<4>[ 0.390000] ->Oops: flash id 0xc22017 .
<6>[ 0.390000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.400000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>[ 0.800000] PPP generic driver version 2.4.2
<6>[ 0.810000] PPP BSD Compression module registered
<6>[ 0.810000] PPP Deflate Compression module registered
<6>[ 0.820000] PPP MPPE Compression module registered
<6>[ 0.820000] NET: Registered protocol family 24
<6>[ 0.830000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 0.860000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 0.870000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<6>[ 0.910000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 0.930000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 0.930000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 0.940000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 0.950000] usb usb1: Product: Atheros AR91xx built-in EHCI controller
<6>[ 0.950000] usb usb1: Manufacturer: Linux 3.10.108 ehci_hcd
<6>[ 0.960000] usb usb1: SerialNumber: platform
<6>[ 0.960000] hub 1-0:1.0: USB hub found
<6>[ 0.970000] hub 1-0:1.0: 1 port detected
<6>[ 0.980000] u32 classifier
<6>[ 0.980000] Performance counters on
<6>[ 0.990000] input device check on
<6>[ 0.990000] Actions configured
<6>[ 1.000000] Netfilter messages via NETLINK v0.30.
<6>[ 1.000000] nf_conntrack version 0.5.0 (452 buckets, 1808 max)
<4>[ 1.010000] nf_conntrack_rtsp v0.7 loading
<4>[ 1.010000] nf_nat_rtsp v0.7 loading
<6>[ 1.010000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 1.020000] TCP: westwood registered
<6>[ 1.020000] TCP: hybla registered
<6>[ 1.030000] TCP: vegas registered
<6>[ 1.030000] NET: Registered protocol family 17
<5>[ 1.040000] Bridge firewalling registered
<6>[ 1.040000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 1.050000] searching for nvram
<6>[ 1.050000] nvram size = 0
<6>[ 1.080000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 1.090000] ar71xx-wdt: timeout=15 secs (max=21) ref freq=200000000
<6>[ 1.100000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 1.110000] Freeing unused kernel memory: 200K
<7>[ 4.130000] ar71xx-wdt: enabling watchdog timer
<6>[ 4.200000] libphy: ag71xx_mdio: probed
<6>[ 4.530000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
<6>[ 4.530000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=00008306, driver=Realtek RTL8306S]
<6>[ 4.540000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RMII
<6>[ 4.870000] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=00008306, driver=Realtek RTL8306S]
<6>[ 4.880000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RMII
<6>[ 5.060000] Loading modules backported from Linux version wireless-drivers-next-for-davem-2017-09-01-0-geb464d4a8d09
<6>[ 5.070000] Backport generated by backports.git backports-20160324-111-g97b8d7c4
<7>[ 5.940000] ath: EEPROM regdomain: 0x0
<7>[ 5.940000] ath: EEPROM indicates default country code should be used
<7>[ 5.940000] ath: doing EEPROM country->regdmn map search
<7>[ 5.940000] ath: country maps to regdmn code: 0x3a
<7>[ 5.940000] ath: Country alpha2 being used: US
<7>[ 5.940000] ath: Regpair used: 0x3a
<7>[ 5.980000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 5.980000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
<7>[ 6.530000] ar71xx: pll_reg 0xb8050014: 0x13000a44
<6>[ 6.530000] eth0: link up (100Mbps/Full duplex)
<7>[ 7.910000] ar71xx: pll_reg 0xb8050018: 0x13000a44
<6>[ 7.910000] eth1: link up (100Mbps/Full duplex)
<6>[ 8.420000] device br0 entered promiscuous mode
<6>[ 8.450000] eth0: link down
<6>[ 8.510000] device eth0 entered promiscuous mode
<6>[ 8.510000] br0: port 1(eth0) entered forwarding state
<6>[ 8.520000] br0: port 1(eth0) entered forwarding state
<6>[ 8.520000] device br0 left promiscuous mode
<6>[ 8.530000] device br0 entered promiscuous mode
<6>[ 8.550000] device br0 left promiscuous mode
<7>[ 8.610000] ath: EEPROM regdomain: 0x8348
<7>[ 8.610000] ath: EEPROM indicates we should expect a country code
<7>[ 8.610000] ath: doing EEPROM country->regdmn map search
<7>[ 8.610000] ath: country maps to regdmn code: 0x3a
<7>[ 8.610000] ath: Country alpha2 being used: US
<7>[ 8.610000] ath: Regpair used: 0x3a
<7>[ 8.610000] ath: regdomain 0x8348 dynamically updated by user
<6>[ 8.910000] br0: port 1(eth0) entered disabled state
<7>[ 9.530000] ar71xx: pll_reg 0xb8050014: 0x13000a44
<6>[ 9.530000] eth0: link up (100Mbps/Full duplex)
<6>[ 9.530000] br0: port 1(eth0) entered forwarding state
<6>[ 9.540000] br0: port 1(eth0) entered forwarding state
<6>[ 11.540000] br0: port 1(eth0) entered forwarding state
<6>[ 13.590000] device ath0 entered promiscuous mode
<6>[ 13.600000] br0: port 2(ath0) entered forwarding state
<6>[ 13.600000] br0: port 2(ath0) entered forwarding state
<6>[ 14.230000] device eth1 entered promiscuous mode
<1>[ 14.550000] fast-classifier: starting up
<1>[ 14.560000] fast-classifier: registered
<6>[ 15.600000] br0: port 2(ath0) entered forwarding state
<6>[ 16.420000] eth1: link down
<6>[ 16.500000] device eth1 left promiscuous mode
<7>[ 16.920000] ar71xx: pll_reg 0xb8050018: 0x13000a44
<6>[ 16.920000] eth1: link up (100Mbps/Full duplex)
<6>[ 138.990000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
root@DD-WRT:~# date
Wed Jul 10 13:12:20 CDT 2019
root@DD-WRT:~# exit
Connection closed by foreign host.
mrjcd@Deb:~$ telnet e2100l-wds-south.mrjcd.com
Trying 10.72.28.57...
Connected to e2100l-wds-south.mrjcd.com.
Escape character is '^]'.
DD-WRT v3.0-r27506 std (c) 2015 NewMedia-NET GmbH
Release: 07/09/15
E2100L-WDS-South login: root
Password:
==========================================================
___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/
DD-WRT v3.0
http://www.dd-wrt.com
==========================================================
BusyBox v1.23.2 (2015-07-09 01:57:54 CEST) built-in shell (ash)
root@E2100L-WDS-South:~# nvram get DD_BOARD
Linksys E2100L
root@E2100L-WDS-South:~# dmesg
<5>[ 0.000000] Linux version 3.10.83 (root@dd-wrt) (gcc version 5.1.0 (OpenWrt GCC 5.1.0 r45886) ) #5666 Thu Jul 9 01:57:41 CEST 2015
<4>[ 0.000000] flash_size passed from bootloader = 8
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
<6>[ 0.000000] booting platform Atheros AR9130 rev 2 (0xb8)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 04000000 @ 00000000 (usable)
<4>[ 0.000000] Zone ranges:
<4>[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
<4>[ 0.000000] Movable zone start for each node
<4>[ 0.000000] Early memory node ranges
<4>[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
<7>[ 0.000000] On node 0 totalpages: 16384
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802f4fa0, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 128 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
<4>[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<6>[ 0.000000] Memory: 61364k/65536k available (2332k kernel code, 4172k reserved, 392k data, 216k init, 0k highmem)
<6>[ 0.000000] NR_IRQS:83
<0>[ 0.000000] irq init done
<4>[ 0.000000] plat_time_init: plat time init done
<6>[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
<6>[ 0.080000] pid_max: default: 32768 minimum: 301
<6>[ 0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<6>[ 0.120000] bio: create slab <bio-0> at 0
<5>[ 0.120000] SCSI subsystem initialized
<6>[ 0.130000] usbcore: registered new interface driver usbfs
<6>[ 0.130000] usbcore: registered new interface driver hub
<6>[ 0.140000] usbcore: registered new device driver usb
<6>[ 0.140000] Switching to clocksource MIPS
<6>[ 0.150000] NET: Registered protocol family 2
<6>[ 0.150000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
<6>[ 0.160000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
<6>[ 0.170000] TCP: Hash tables configured (established 512 bind 512)
<6>[ 0.170000] TCP: reno registered
<6>[ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.190000] NET: Registered protocol family 1
<5>[ 0.190000] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.200000] Register LED Device
<5>[ 0.200000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<4>[ 0.210000] AR7100 GPIOC major 0
<6>[ 0.220000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.220000] msgmni has been set to 119
<6>[ 0.230000] io scheduler noop registered
<6>[ 0.230000] io scheduler deadline registered (default)
<6>[ 0.230000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.260000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
<6>[ 0.270000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.280000] guessed flashsize = 8M
<0>[ 0.290000] scanning for root partition
<0>[ 0.290000] WRT160NL/E2100L uboot detected
<0>[ 0.290000] bootloader size = 40000
<0>[ 0.300000]
<0>[ 0.300000] found squashfs at 193000
<5>[ 0.310000] Creating 8 MTD partitions on "ar7100-nor0":
<5>[ 0.310000] 0x000000000000-0x000000040000 : "RedBoot"
<5>[ 0.320000] 0x000000040000-0x0000007e0000 : "linux"
<5>[ 0.330000] 0x000000193000-0x000000790000 : "rootfs"
<4>[ 0.330000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>[ 0.350000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.350000] 0x000000790000-0x0000007e0000 : "ddwrt"
<5>[ 0.360000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.360000] 0x0000007f0000-0x000000800000 : "FIS directory"
<5>[ 0.370000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.380000] 0x000000000000-0x000000800000 : "fullflash"
<4>[ 0.390000] ->Oops: flash id 0xc22017 .
<6>[ 0.390000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.400000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>[ 0.800000] PPP generic driver version 2.4.2
<6>[ 0.810000] PPP BSD Compression module registered
<6>[ 0.810000] PPP Deflate Compression module registered
<6>[ 0.820000] PPP MPPE Compression module registered
<6>[ 0.820000] NET: Registered protocol family 24
<6>[ 0.830000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 0.860000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 0.870000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<6>[ 0.910000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 0.930000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 0.930000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 0.940000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 0.950000] usb usb1: Product: Atheros AR91xx built-in EHCI controller
<6>[ 0.950000] usb usb1: Manufacturer: Linux 3.10.83 ehci_hcd
<6>[ 0.960000] usb usb1: SerialNumber: platform
<6>[ 0.960000] hub 1-0:1.0: USB hub found
<6>[ 0.970000] hub 1-0:1.0: 1 port detected
<6>[ 0.980000] u32 classifier
<6>[ 0.980000] Performance counters on
<6>[ 0.990000] input device check on
<6>[ 0.990000] Actions configured
<6>[ 1.000000] Netfilter messages via NETLINK v0.30.
<6>[ 1.000000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
<4>[ 1.010000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 1.010000] nf_nat_rtsp v0.6.21 loading
<6>[ 1.020000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 1.020000] TCP: westwood registered
<6>[ 1.020000] TCP: hybla registered
<6>[ 1.030000] TCP: vegas registered
<6>[ 1.030000] NET: Registered protocol family 17
<5>[ 1.040000] Bridge firewalling registered
<6>[ 1.040000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 1.050000] searching for nvram
<6>[ 1.050000] nvram size = 0
<6>[ 1.080000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 1.090000] ar71xx-wdt: timeout=15 secs (max=21) ref freq=200000000
<6>[ 1.100000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 1.110000] Freeing unused kernel memory: 216K (8030a000 - 80340000)
<7>[ 3.710000] ar71xx-wdt: enabling watchdog timer
<6>[ 3.810000] libphy: ag71xx_mdio: probed
<6>[ 4.140000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
<6>[ 4.140000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=00008306, driver=Realtek RTL8306S]
<6>[ 4.150000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RMII
<6>[ 4.480000] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=00008306, driver=Realtek RTL8306S]
<6>[ 4.490000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RMII
<6>[ 4.650000] Loading modules backported from Linux version master-2015-06-22-0-g4732c92
<6>[ 4.660000] Backport generated by backports.git backports-20150612-0-g1b838d0
<6>[ 4.820000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 4.850000] cfg80211: World regulatory domain updated:
<6>[ 4.850000] cfg80211: DFS Master region: unset
<6>[ 4.850000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 4.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 4.870000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 4.880000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 4.890000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 4.900000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 4.900000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<7>[ 5.490000] ath: EEPROM regdomain: 0x0
<7>[ 5.490000] ath: EEPROM indicates default country code should be used
<7>[ 5.490000] ath: doing EEPROM country->regdmn map search
<7>[ 5.490000] ath: country maps to regdmn code: 0x3a
<7>[ 5.490000] ath: Country alpha2 being used: US
<7>[ 5.490000] ath: Regpair used: 0x3a
<7>[ 5.530000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 5.530000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
<6>[ 5.540000] cfg80211: Calling CRDA for country: US
<6>[ 5.540000] cfg80211: Regulatory domain changed to country: US
<6>[ 5.550000] cfg80211: DFS Master region: FCC
<6>[ 5.550000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 5.560000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 5.570000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 5.580000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 5.590000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 5.600000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<7>[ 6.170000] ar71xx: pll_reg 0xb8050014: 0x13000a44
<6>[ 6.170000] eth0: link up (100Mbps/Full duplex)
<6>[ 8.250000] device br0 entered promiscuous mode
<6>[ 8.270000] eth0: link down
<6>[ 8.320000] device eth0 entered promiscuous mode
<6>[ 8.320000] br0: port 1(eth0) entered forwarding state
<6>[ 8.330000] br0: port 1(eth0) entered forwarding state
<6>[ 8.390000] device eth1 entered promiscuous mode
<6>[ 8.390000] device br0 left promiscuous mode
<6>[ 8.400000] device br0 entered promiscuous mode
<6>[ 8.450000] cfg80211: Calling CRDA to update world regulatory domain
<3>[ 8.470000] cfg80211: Invalid regulatory domain detected:
<6>[ 8.480000] cfg80211: Regulatory domain: 00
<6>[ 8.480000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 8.490000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.500000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.510000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.520000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.520000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.530000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 8.560000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 8.570000] cfg80211: World regulatory domain updated:
<6>[ 8.570000] cfg80211: DFS Master region: unset
<6>[ 8.580000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 8.590000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.590000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.600000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.610000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.620000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.630000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 8.650000] cfg80211: Calling CRDA for country: NZ
<6>[ 8.650000] cfg80211: Regulatory domain changed to country: NZ
<6>[ 8.660000] cfg80211: DFS Master region: FCC
<6>[ 8.660000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 8.670000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 8.680000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 8.690000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2400 mBm), (N/A)
<6>[ 8.700000] cfg80211: (5490000 KHz - 5730000 KHz @ 80000 KHz), (N/A, 2400 mBm), (N/A)
<6>[ 8.710000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 9.090000] br0: port 1(eth0) entered disabled state
<6>[ 9.250000] device ath0 entered promiscuous mode
<6>[ 9.260000] br0: port 3(ath0) entered forwarding state
<6>[ 9.260000] br0: port 3(ath0) entered forwarding state
<6>[ 10.090000] br0: port 3(ath0) entered disabled state
<7>[ 10.210000] ar71xx: pll_reg 0xb8050014: 0x13000a44
<6>[ 10.210000] eth0: link up (100Mbps/Full duplex)
<6>[ 10.210000] br0: port 1(eth0) entered forwarding state
<6>[ 10.220000] br0: port 1(eth0) entered forwarding state
<6>[ 10.810000] br0: port 3(ath0) entered forwarding state
<6>[ 10.820000] br0: port 3(ath0) entered forwarding state
<6>[ 10.970000] device ath0.wds0 entered promiscuous mode
<6>[ 10.990000] device br0 left promiscuous mode
<6>[ 12.220000] br0: port 1(eth0) entered forwarding state
<6>[ 12.330000] device ath0.sta1 entered promiscuous mode
<6>[ 12.330000] br0: port 5(ath0.sta1) entered forwarding state
<6>[ 12.340000] br0: port 5(ath0.sta1) entered forwarding state
<6>[ 12.820000] br0: port 3(ath0) entered forwarding state
<6>[ 13.340000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<6>[ 14.340000] br0: port 5(ath0.sta1) entered forwarding state
root@E2100L-WDS-South:~# date
Wed Jul 10 13:13:03 CDT 2019
root@E2100L-WDS-South:~# exit
Connection closed by foreign host.
mrjcd@Deb:~$