https://svn.dd-wrt.com/ticket/6580 ### I know the r39180 is too big but just for the hell of it and to see what serial has to say. I'm currently on linux2 (part2....the smaller one) running r38581 with defaults so she should try to load onto part1 which has r38688. Hmmm, oh well I haven't kill it yet :-) ### full serial log below (bootup r38581 / attempt GUI install r39180 / reboots into r38688) ### U-Boot 2012.07 [Standard IPQ806X.LN,r40331] (Mar 16 2015 - 16:29:21) CBT U-Boot ver: 1.0.9 smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:0:3:7f:ba:db:2 eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is 00:06:3b:01:41:00 , eth1 Updating boot_count ... done Hit any key to stop autoboot: 2  1  0 MMC Device 0 not found MMC Device 0 not found Loading from nand0, offset 0x3780000 Image Name: DD-WRT V3.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2228095 Bytes = 2.1 MiB Load Address: 42208000 Entry Point: 42208000 Automatic boot of image at addr 0x44000000 ... Image Name: DD-WRT V3.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2228095 Bytes = 2.1 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK Loading Kernel Image ... OK OK mtdids not defined, no default present info: "mtdparts" not set Using machid 0x1260 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.155-rc1 (root@seg-desktop) (gcc version 8.2.0 (OpenWrt GCC 8.2.0 r7577-d14647dd59) ) #255 SMP Mon Feb 4 14:10:03 CET 2019 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt:Machine model: Linksys EA8500 WiFi Router [ 0.000000] OF: fdt:Ignoring memory range 0x41500000 - 0x42000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 13 pages/cpu @ddc06000 s20812 r8192 d24244 u53248 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:16 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 478140K/491520K available (5120K kernel code, 277K rwdata, 1060K rodata, 1024K init, 399K bss, 13380K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0800000 (6112 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b45500 ( 278 kB) [ 0.000000] .bss : 0xc0b47000 - 0xc0baae3c ( 400 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000006] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000020] Switching to timer-based delay loop, resolution 160ns [ 0.000194] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000215] pid_max: default: 32768 minimum: 301 [ 0.000341] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000357] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000941] CPU: Testing write buffer coherency: ok [ 0.001226] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001276] Setting up static identity map for 0x42300000 - 0x42300034 [ 0.004371] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.004582] Brought up 2 CPUs [ 0.004600] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.004610] CPU: All CPU(s) started in SVC mode. [ 0.017266] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.017456] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017480] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.017567] pinctrl core: initialized pinctrl subsystem [ 0.018870] NET: Registered protocol family 16 [ 0.019226] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.051767] cpuidle: using governor ladder [ 0.082784] cpuidle: using governor menu [ 0.135633] msm_bus_fabric_init_driver [ 0.136550] pps_core: LinuxPPS API ver. 1 registered [ 0.136564] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.136606] PTP clock support registered [ 0.138476] clocksource: Switched to clocksource dg_timer [ 0.142534] NET: Registered protocol family 2 [ 0.143190] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.143231] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.143285] TCP: Hash tables configured (established 4096 bind 4096) [ 0.143338] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.143363] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.143544] NET: Registered protocol family 1 [ 0.153549] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.163090] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.165699] io scheduler noop registered [ 0.165716] io scheduler deadline registered (default) [ 0.167448] 1b500000.pci supply vdda not found, using dummy regulator [ 0.167557] 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.167642] 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.168449] OF: PCI: host bridge /soc/pci@1b500000 ranges: [ 0.168495] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.168521] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.277175] qcom-pcie 1b500000.pci: link up [ 0.277354] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.277377] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.277399] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.277414] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.277935] PCI: bus0: Fast back to back transfers disabled [ 0.280408] PCI: bus1: Fast back to back transfers disabled [ 0.280701] pci 0000:00:00.0: BAR 14: assigned [mem 0x08000000-0x081fffff] [ 0.280726] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.280862] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.280884] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.281741] 1b700000.pci supply vdda not found, using dummy regulator [ 0.281844] 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.281930] 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.282708] OF: PCI: host bridge /soc/pci@1b700000 ranges: [ 0.282744] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.282766] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.393008] qcom-pcie 1b700000.pci: link up [ 0.393178] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.393196] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.393219] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.393666] PCI: bus0: Fast back to back transfers disabled [ 0.395882] PCI: bus1: Fast back to back transfers disabled [ 0.396257] pci 0001:00:00.0: BAR 14: assigned [mem 0x2e000000-0x2e1fffff] [ 0.396280] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.396402] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.396423] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.397795] deviceless supply s1b not found, using dummy regulator [ 0.399925] L2 @ QSB rate. Forcing new rate. [ 0.400100] L2 @ 800000 KHz [ 0.400210] CPU0 @ 800000 KHz [ 0.400220] CPU1 @ QSB rate. Forcing new rate. [ 0.400344] CPU1 @ 800000 KHz [ 0.402489] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.403971] serial8250_init [ 0.403985] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.405039] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.405120] msm_serial 16340000.serial: uartclk = 7372800 [ 0.405176] physical 16340000 = virtual de879000 [ 0.405191] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 168, base_baud = 460800) is a MSM [ 0.405227] msm_serial: console setup on port #0 [ 1.103508] console [ttyMSM0] enabled [ 1.108193] msm_serial: driver initialized [ 1.113521] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1 [ 1.115565] nand: AMD/Spansion S34MS01G2 [ 1.122146] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.126994] 19 ofpart partitions found on MTD device qcom_nand.0 [ 1.133458] Creating 19 MTD partitions on "qcom_nand.0": [ 1.139615] 0x000000000000-0x000000040000 : "SBL1" [ 1.146074] 0x000000040000-0x000000180000 : "MIBIB" [ 1.151999] 0x000000180000-0x0000002c0000 : "SBL2" [ 1.156695] 0x0000002c0000-0x000000540000 : "SBL3" [ 1.159743] random: fast init done [ 1.167344] 0x000000540000-0x000000660000 : "DDRCONFIG" [ 1.169824] 0x000000660000-0x000000780000 : "SSD" [ 1.174725] 0x000000780000-0x000000a00000 : "TZ" [ 1.181473] 0x000000a00000-0x000000c80000 : "RPM" [ 1.186115] 0x000000c80000-0x000000dc0000 : "art" [ 1.189061] 0x000000dc0000-0x000000ec0000 : "APPSBL" [ 1.193450] 0x000000ec0000-0x000000f00000 : "u_env" [ 1.197363] 0x000000f00000-0x000000f40000 : "s_env" [ 1.202240] 0x000000f40000-0x000000f80000 : "devinfo" [ 1.207016] 0x000000f80000-0x000003780000 : "linux" [ 1.265985] 0x000001280000-0x000003780000 : "rootfs" [ 1.316960] mtd: partition "rootfs" set to be root filesystem [ 1.316992] 0x000003780000-0x000005f40000 : "linux2" [ 1.376474] 0x000003a80000-0x000005f40000 : "rootfs2" [ 1.427177] 0x000005f40000-0x000005f80000 : "nvram" [ 1.428535] 0x000005f80000-0x000008000000 : "ddwrt" [ 1.452837] random: crng init done [ 1.477081] libphy: GPIO Bitbanged MDIO: probed [ 1.480358] libphy: Fixed MDIO Bus: probed [ 1.502082] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 2.364525] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.364550] Ring mode enabled [ 2.368545] DMA HW capability register supported[ 2.371594] Enhanced/Alternate descriptors [ 2.377143] Enabled extended descriptors [ 2.380175] RX Checksum Offload Engine supported [ 2.384268] COE Type 2 [ 2.389016] TX Checksum insertion supported [ 2.391212] Wake-Up On Lan supported [ 2.395726] Enable RX Mitigation via HW Watchdog Timer [ 2.400624] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.404320] Ring mode enabled [ 2.409608] DMA HW capability register supported[ 2.412482] Enhanced/Alternate descriptors [ 2.418120] Enabled extended descriptors [ 2.421129] RX Checksum Offload Engine supported [ 2.425248] COE Type 2 [ 2.430003] TX Checksum insertion supported [ 2.432190] Wake-Up On Lan supported [ 2.436704] Enable RX Mitigation via HW Watchdog Timer [ 2.440921] i2c /dev entries driver [ 2.445954] Calibration not found. [ 2.448843] qcom-tsens 900000.thermal-sensor: tsens calibration failed [ 2.453317] CPUidle arm: CPU 0 failed to init idle CPU ops [ 2.459159] GACT probability NOT on [ 2.464232] Mirror/redirect action on [ 2.467636] Simple TC action Loaded [ 2.472050] netem: version 1.3 [ 2.474735] u32 classifier [ 2.477848] Performance counters on [ 2.480612] input device check on [ 2.484272] Actions configured [ 2.488100] Netfilter messages via NETLINK v0.30. [ 2.491715] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 2.496790] nf_conntrack_rtsp v0.7 loading [ 2.502530] xt_time: kernel timezone is -0000 [ 2.506161] ip_set: protocol 6 [ 2.510840] gre: GRE over IPv4 demultiplexor driver [ 2.513917] nf_nat_rtsp v0.7 loading [ 2.518329] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.522386] NET: Registered protocol family 17 [ 2.527491] Bridge firewalling registered [ 2.531780] 8021q: 802.1Q VLAN Support v1.8 [ 2.535884] Registering SWP/SWPB emulation handler [ 2.549569] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 2.568298] s1a: Bringing 0uV into 1050000-1050000uV [ 2.568558] s1b: Bringing 0uV into 1050000-1050000uV [ 2.572638] s2a: Bringing 0uV into 800000-800000uV [ 2.577491] s2b: Bringing 0uV into 800000-800000uV [ 2.585946] trying to register driver cpufreq-dt [ 2.588221] searching for nvram [ 2.591515] nvram size = 262144 [ 2.634734] no valid UBI magic found inside mtd13[ 2.634·[ 2.643900] VFS: Mounted root (squashfs filesystem) readonly on device 31:16. [ 2.645450] Freeing unused kernel memory: 1024K start service starting Architecture code for ipq806x cannot open /dev/nvram cannot open /dev/nvram udevtrigger[95]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory sysinit using mac C0:56:27:08:B2:92 mount: mounting ubi0:rootfs_data on /jffs failed: No such device reset boot counter load ATH 802.11 a/b/g Driver insmod: ath_pci.ko: module not found insmod: ath_ahb.ko: module not found load ATH9K 802.11n Driver [ 5.454744] Loading modules backported from Linux version wireless-drivers-next-for-davem-2017-09-01-0-geb464d4a8d09 [ 5.454776] Backport generated by backports.git backports-20160324-111-g97b8d7c4 load ATH/QCA 802.11ac Driver [ 5.969353] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 5.970008] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 6.130747] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2 [ 6.130779] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.141677] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2 [ 6.146497] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.510820] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 6.510857] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 6.521952] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 8.855259] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 8.855648] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 d3e0cdb5 [ 10.066252] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 10.167462] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 10.168106] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 10.330763] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2 [ 10.330809] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.342122] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2 [ 10.346527] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.358284] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 10.363308] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 10.377642] ath10k_pci 0001:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 12.668034] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 12.668301] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 402a8111 [ 13.934109] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 15.003712] dwmac1000: Master AXI performs any burst length [ 15.003777] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 15.008356] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 15.048648] dwmac1000: Master AXI performs any burst length [ 15.048695] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 15.053481] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [USB] checking... umount: can't unmount /mnt: No such file or directory /etc/preinit: line 40: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_max: nonexistent directory /etc/preinit: line 41: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established: nonexistent directory /etc/preinit: line 42: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout: nonexistent directory cannot open /proc/sys/net/ipv4/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout [ 16.093428] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off /etc/preinit: line 40: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_max: nonexistent directory /etc/preinit: line 41: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established: nonexistent directory /etc/preinit: line 42: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout: nonexistent directory cannot open /proc/sys/net/ipv4/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout route: ioctl 0x890c failed: No such process route: ioctl 0x890b failed: Network unreachable ath9k deconfigure_single: phy0 ath0 interface wlan0 does not exist! ath9k deconfigure_single: phy1 ath1 interface wlan1 does not exist! [ 16.956192] device br0 entered promiscuous mode killall: ead: no process killed [ 17.003571] br0: port 1(vlan1) entered blocking state [ 17.003596] br0: port 1(vlan1) entered disabled state [ 17.007844] device vlan1 entered promiscuous mode [ 17.012715] device eth0 entered promiscuous mode sh: ead: not found [ 17.023953] br0: port 1(vlan1) entered blocking state [ 17.023976] br0: port 1(vlan1) entered forwarding state [ 17.028737] device br0 left promiscuous mode [ 17.036639] device br0 entered promiscuous mode ifconfig: ioctl 0x8914 failed: Address not available [ 17.047930] device br0 left promiscuous mode ath9k deconfigure_single: phy0 ath0 ath9k deconfigure_single: phy1 ath1 ath9k configure_single: phy0 ath0 sh: can't create /sys/kernel/debug/ieee80211/phy0/ath9k/chanbw: nonexistent directory [ 21.246687] Core CLK 300 [ 21.246710] Mac CLK 150 setup ath0 C0:56:27:08:B2:94 Configuration file: /tmp/ath0_hostap.conf [ 23.296923] br0: port 2(ath0) entered blocking state [ 23.296946] br0: port 2(ath0) entered disabled state [ 23.301219] device ath0 entered promiscuous mode ath0: interface state UNINITIALIZED->COUNTRY_UPDATE Using interface ath0 with hwaddr c0:56:27:08:b2:94 and ssid "dd-wrt" [ 23.859106] br0: port 2(ath0) entered blocking state [ 23.859131] br0: port 2(ath0) entered forwarding state ath0: interface state COUNTRY_UPDATE->ENABLED ath0: AP-ENABLED ath9k configure_single: phy1 ath1 sh: can't create /sys/kernel/debug/ieee80211/phy1/ath9k/chanbw: nonexistent directory [ 23.916890] Core CLK 300 [ 23.916907] Mac CLK 150 setup ath1 C0:56:27:08:B2:95 Configuration file: /tmp/ath1_hostap.conf [ 25.297844] br0: port 3(ath1) entered blocking state [ 25.297868] br0: port 3(ath1) entered disabled state [ 25.302129] device ath1 entered promiscuous mode ath1: interface state UNINITIALIZED->COUNTRY_UPDATE Using interface ath1 with hwaddr c0:56:27:08:b2:95 and ssid "dd-wrt" [ 25.721647] br0: port 3(ath1) entered blocking state [ 25.721668] br0: port 3(ath1) entered forwarding state ath1: interface state COUNTRY_UPDATE->ENABLED ath1: AP-ENABLED killall: roaming_daemon: no process killed route: ioctl 0x890c failed: No such process route: ioctl 0x890b failed: Network unreachable route: ioctl 0x890c failed: No such process route: ioctl 0x890b failed: Network unreachable sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max: nonexistent directory [ 25.953377] fast-classifier: starting up [ 25.953446] fast-classifier: registered sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max_hyst: nonexistent directory cp: can't stat '/tmp/mycron.d/*': No such file or directory cp: can't stat '/jffs/mycron.d/*': No such file or directory cp: can't stat '/mmc/mycron.d/*': No such file or directory [ 26.027604] device vlan2 entered promiscuous mode rmmod: eoip: No such file or directory cat: can't open '/proc/net/ip_conntrack_flush': No such file or directory 0 cannot open /proc/sys/net/ipv4/conf/br0/loop [ 26.813449] device vlan2 left promiscuous mode udhcpc: started, v1.30.0 ath9k radio 1: phy0 ath0 ath9k radio 1: phy1 ath1 cannot open /proc/sys/dev/wifi0/silent cannot open /proc/sys/dev/wifi1/silent udhcpc: sending discover nvram was changed, needs commit, waiting 10 sec. udhcpc: sending select for 10.72.28.52 /opt/etc/init.d/rcS: No such file or directory /jffs/etc/init.d/rcS: No such file or directory /mmc/etc/init.d/rcS: No such file or directory udhcpc: lease of 10.72.28.52 obtained, lease time 86400 vlan2: No such process killall: proxywatchdog.sh: no process killed /mnt/smbshare umount: can't unmount /mnt/smbshare: No such file or directory rmmod: cifs: No such file or directory rmmod: fscache: No such file or directory killall: schedulerb.sh: no process killed killall: shatd: no process killed rmmod: eoip: No such file or directory killall: wdswatchdog.sh: no process killed The Milkfish Router Services ERROR: Necessary service setting not found: milkfish_username - aborting. The Milkfish Router Services Restoring SIP ddsubscriber database from NVRAM... Empty. The Milkfish Router Services Restoring SIP ddaliases database from NVRAM... Empty. cp: can't stat '/tmp/mycron.d/*': No such file or directory cp: can't stat '/jffs/mycron.d/*': No such file or directory cp: can't stat '/mmc/mycron.d/*': No such file or directory cat: can't open '/proc/net/ip_conntrack_flush': No such file or directory 0 cannot open /proc/sys/net/ipv4/conf/br0/loop rmmod: eoip: No such file or directory use buffer size 65536 boot partiton is 2 a_pEnv->crc = 8e538d15 crc32 = 8e538d15 flash to partition linux Upgrading from web (http) now ... upgrade_ver[v206.1.0] upgrade_ver[2060100] intel_ver[14108] 4712_ver[15000] uploading [65536] umount: can't unmount /jffs: Invalid argument Image too big for partition: linux linux: Invalid argument uploading [131072] uploading [196608] uploading [262144] uploading [327680] uploading [345423] uploading [345423] [UPGRADE] ret: 0 send dhcp lease release signal Sending SIGTERM to all processes [ 242.370280] watchdog: watchdog0: watchdog did not stop! [ 242.409867] init (1): drop_caches: 3 unmounting / [ 242.434814] device ath1 left promiscuous mode [ 242.434886] br0: port 3(ath1) entered disabled state [ 242.465542] device ath0 left promiscuous mode [ 242.465615] br0: port 2(ath0) entered disabled state [ 242.511684] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 1 [ 242.511723] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 1 [ 242.517555] ath10k_pci 0000:01:00.0: peer-unmap-event: unknown peer id 1 Sending SIGKILL to all processes [ 242.635877] init (1): drop_caches: 3 unmounting / [ 243.098838] reboot: Restarting system [ 243.098873] [ 243.098873] Resetting with watch dog! U-Boot 2012.07 [Standard IPQ806X.LN,r40331] (Mar 16 2015 - 16:29:21) CBT U-Boot ver: 1.0.9 smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:0:3:7f:ba:db:2 eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is 00:06:3b:01:41:00 , eth1 Updating boot_count ... done Hit any key to stop autoboot: 2  1  0 MMC Device 0 not found MMC Device 0 not found Loading from nand0, offset 0xf80000 Image Name: DD-WRT V3.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2228095 Bytes = 2.1 MiB Load Address: 42208000 Entry Point: 42208000 Automatic boot of image at addr 0x44000000 ... Image Name: DD-WRT V3.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2228095 Bytes = 2.1 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK Loading Kernel Image ... OK OK mtdids not defined, no default present info: "mtdparts" not set Using machid 0x1260 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.155 (root@seg-desktop) (gcc version 8.2.0 (OpenWrt GCC 8.2.0 r7577-d14647dd59) ) #258 SMP Fri Feb 8 11:09:47 CET 2019 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt:Machine model: Linksys EA8500 WiFi Router [ 0.000000] OF: fdt:Ignoring memory range 0x41500000 - 0x42000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 13 pages/cpu @ddc06000 s20812 r8192 d24244 u53248 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 478140K/491520K available (5120K kernel code, 277K rwdata, 1060K rodata, 1024K init, 399K bss, 13380K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0800000 (6112 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b45500 ( 278 kB) [ 0.000000] .bss : 0xc0b47000 - 0xc0baae3c ( 400 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000007] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000020] Switching to timer-based delay loop, resolution 160ns [ 0.000193] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000218] pid_max: default: 32768 minimum: 301 [ 0.000346] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000360] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000945] CPU: Testing write buffer coherency: ok [ 0.001225] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001274] Setting up static identity map for 0x42300000 - 0x42300034 [ 0.004344] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.004546] Brought up 2 CPUs [ 0.004567] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.004576] CPU: All CPU(s) started in SVC mode. [ 0.016757] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.016943] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016968] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.017058] pinctrl core: initialized pinctrl subsystem [ 0.018336] NET: Registered protocol family 16 [ 0.018688] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.041400] cpuidle: using governor ladder [ 0.072416] cpuidle: using governor menu [ 0.125263] msm_bus_fabric_init_driver [ 0.126157] pps_core: LinuxPPS API ver. 1 registered [ 0.126172] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.126213] PTP clock support registered [ 0.128048] clocksource: Switched to clocksource dg_timer [ 0.132048] NET: Registered protocol family 2 [ 0.132697] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.132740] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.132792] TCP: Hash tables configured (established 4096 bind 4096) [ 0.132845] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.132868] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.133047] NET: Registered protocol family 1 [ 0.142797] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.152153] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.154753] io scheduler noop registered [ 0.154768] io scheduler deadline registered (default) [ 0.156462] 1b500000.pci supply vdda not found, using dummy regulator [ 0.156572] 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.156655] 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.157448] OF: PCI: host bridge /soc/pci@1b500000 ranges: [ 0.157492] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.157518] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.266150] qcom-pcie 1b500000.pci: link up [ 0.266328] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.266352] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.266371] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.266387] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.266903] PCI: bus0: Fast back to back transfers disabled [ 0.269364] PCI: bus1: Fast back to back transfers disabled [ 0.269661] pci 0000:00:00.0: BAR 14: assigned [mem 0x08000000-0x081fffff] [ 0.269687] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.269822] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.269845] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.270692] 1b700000.pci supply vdda not found, using dummy regulator [ 0.270800] 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.270887] 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.271646] OF: PCI: host bridge /soc/pci@1b700000 ranges: [ 0.271681] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.271703] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.381924] qcom-pcie 1b700000.pci: link up [ 0.382093] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.382112] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.382134] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.382573] PCI: bus0: Fast back to back transfers disabled [ 0.384780] PCI: bus1: Fast back to back transfers disabled [ 0.385149] pci 0001:00:00.0: BAR 14: assigned [mem 0x2e000000-0x2e1fffff] [ 0.385173] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.385295] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.385314] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.386653] deviceless supply s1b not found, using dummy regulator [ 0.388734] L2 @ QSB rate. Forcing new rate. [ 0.388907] L2 @ 800000 KHz [ 0.389014] CPU0 @ 800000 KHz [ 0.389024] CPU1 @ QSB rate. Forcing new rate. [ 0.389143] CPU1 @ 800000 KHz [ 0.391230] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.392672] serial8250_init [ 0.392685] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.393696] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.393778] msm_serial 16340000.serial: uartclk = 7372800 [ 0.393833] physical 16340000 = virtual de879000 [ 0.393848] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 168, base_baud = 460800) is a MSM [ 0.393882] msm_serial: console setup on port #0 [ 1.091797] console [ttyMSM0] enabled [ 1.096496] msm_serial: driver initialized [ 1.101792] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1 [ 1.103876] nand: AMD/Spansion S34MS01G2 [ 1.110466] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.114984] 19 ofpart partitions found on MTD device qcom_nand.0 [ 1.121763] Creating 19 MTD partitions on "qcom_nand.0": [ 1.127841] 0x000000000000-0x000000040000 : "SBL1" [ 1.134490] 0x000000040000-0x000000180000 : "MIBIB" [ 1.140280] 0x000000180000-0x0000002c0000 : "SBL2" [ 1.144985] 0x0000002c0000-0x000000540000 : "SBL3" [ 1.147959] random: fast init done [ 1.155732] 0x000000540000-0x000000660000 : "DDRCONFIG" [ 1.158071] 0x000000660000-0x000000780000 : "SSD" [ 1.163078] 0x000000780000-0x000000a00000 : "TZ" [ 1.169729] 0x000000a00000-0x000000c80000 : "RPM" [ 1.174418] 0x000000c80000-0x000000dc0000 : "art" [ 1.177292] 0x000000dc0000-0x000000ec0000 : "APPSBL" [ 1.181780] 0x000000ec0000-0x000000f00000 : "u_env" [ 1.185644] 0x000000f00000-0x000000f40000 : "s_env" [ 1.190368] 0x000000f40000-0x000000f80000 : "devinfo" [ 1.195134] 0x000000f80000-0x000003780000 : "linux" [ 1.254019] 0x000001280000-0x000003780000 : "rootfs" [ 1.305730] mtd: partition "rootfs" set to be root filesystem [ 1.305761] 0x000003780000-0x000005f40000 : "linux2" [ 1.366114] 0x000003a80000-0x000005f40000 : "rootfs2" [ 1.416952] 0x000005f40000-0x000005f80000 : "nvram" [ 1.418414] 0x000005f80000-0x000008000000 : "ddwrt" [ 1.442882] random: crng init done [ 1.467260] libphy: GPIO Bitbanged MDIO: probed [ 1.470536] libphy: Fixed MDIO Bus: probed [ 1.491405] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 2.349151] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.349174] Ring mode enabled [ 2.353172] DMA HW capability register supported[ 2.356125] Enhanced/Alternate descriptors [ 2.361766] Enabled extended descriptors [ 2.364726] RX Checksum Offload Engine supported [ 2.368965] COE Type 2 [ 2.373576] TX Checksum insertion supported [ 2.375834] Wake-Up On Lan supported [ 2.380398] Enable RX Mitigation via HW Watchdog Timer [ 2.385237] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.389030] Ring mode enabled [ 2.394148] DMA HW capability register supported[ 2.397104] Enhanced/Alternate descriptors [ 2.402745] Enabled extended descriptors [ 2.405703] RX Checksum Offload Engine supported [ 2.409950] COE Type 2 [ 2.414554] TX Checksum insertion supported [ 2.416813] Wake-Up On Lan supported [ 2.421385] Enable RX Mitigation via HW Watchdog Timer [ 2.425436] i2c /dev entries driver [ 2.430611] Calibration not found. [ 2.433402] qcom-tsens 900000.thermal-sensor: tsens calibration failed [ 2.437928] CPUidle arm: CPU 0 failed to init idle CPU ops [ 2.443758] GACT probability NOT on [ 2.448917] Mirror/redirect action on [ 2.452264] Simple TC action Loaded [ 2.456577] netem: version 1.3 [ 2.459415] u32 classifier [ 2.462470] Performance counters on [ 2.465163] input device check on [ 2.468963] Actions configured [ 2.472723] Netfilter messages via NETLINK v0.30. [ 2.476276] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 2.481481] nf_conntrack_rtsp v0.7 loading [ 2.487058] xt_time: kernel timezone is -0000 [ 2.490851] ip_set: protocol 6 [ 2.495386] gre: GRE over IPv4 demultiplexor driver [ 2.498686] nf_nat_rtsp v0.7 loading [ 2.502948] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.506933] NET: Registered protocol family 17 [ 2.512188] Bridge firewalling registered [ 2.516295] 8021q: 802.1Q VLAN Support v1.8 [ 2.520582] Registering SWP/SWPB emulation handler [ 2.533922] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 2.552759] s1a: Bringing 0uV into 1050000-1050000uV [ 2.553017] s1b: Bringing 0uV into 1050000-1050000uV [ 2.556994] s2a: Bringing 0uV into 800000-800000uV [ 2.562035] s2b: Bringing 0uV into 800000-800000uV [ 2.570279] trying to register driver cpufreq-dt [ 2.572651] searching for nvram [ 2.575899] nvram size = 262144 [ 2.618782] no valid UBI magic found inside mtd13[ 2.61ü[ 2.627827] VFS: Mounted root (squashfs filesystem) readonly on device 31:14. [ 2.629451] Freeing unused kernel memory: 1024K start service starting Architecture code for ipq806x cannot open /dev/nvram cannot open /dev/nvram udevtrigger[95]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory sysinit using mac C0:56:27:08:B2:92 mount: mounting ubi0:rootfs_data on /jffs failed: No such device reset boot counter load ATH 802.11 a/b/g Driver insmod: ath_pci.ko: module not found insmod: ath_ahb.ko: module not found load ATH9K 802.11n Driver [ 5.715637] Loading modules backported from Linux version wireless-drivers-next-for-davem-2017-09-01-0-geb464d4a8d09 [ 5.715672] Backport generated by backports.git backports-20160324-111-g97b8d7c4 load ATH/QCA 802.11ac Driver [ 6.223358] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 6.224011] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 6.390349] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2 [ 6.390383] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.401262] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2 [ 6.406103] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.811139] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 6.811177] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 6.822265] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 9.122710] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 9.122939] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 d3e0cdb5 [ 10.334454] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 10.428197] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 10.428979] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 10.590332] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2 [ 10.590377] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.602020] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2 [ 10.606095] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.617851] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 10.622884] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 10.637207] ath10k_pci 0001:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 12.935443] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 12.935700] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 402a8111 [ 14.198409] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 15.270107] dwmac1000: Master AXI performs any burst length [ 15.270149] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 15.274624] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 15.307771] dwmac1000: Master AXI performs any burst length [ 15.307819] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 15.312372] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [USB] checking... umount: can't unmount /mnt: No such file or directory /etc/preinit: line 40: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_max: nonexistent directory /etc/preinit: line 41: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established: nonexistent directory /etc/preinit: line 42: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout: nonexistent directory cannot open /proc/sys/net/ipv4/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout [ 16.333435] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off /etc/preinit: line 40: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_max: nonexistent directory /etc/preinit: line 41: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established: nonexistent directory /etc/preinit: line 42: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout: nonexistent directory cannot open /proc/sys/net/ipv4/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout route: ioctl 0x890c failed: No such process route: ioctl 0x890b failed: Network unreachable ath9k deconfigure_single: phy0 ath0 interface wlan0 does not exist! ath9k deconfigure_single: phy1 ath1 interface wlan1 does not exist! [ 17.202676] device br0 entered promiscuous mode killall: ead: no process killed [ 17.259577] br0: port 1(vlan1) entered blocking state [ 17.259609] br0: port 1(vlan1) entered disabled state [ 17.263918] device vlan1 entered promiscuous mode [ 17.268789] device eth0 entered promiscuous mode sh: ead: not found [ 17.280203] br0: port 1(vlan1) entered blocking state [ 17.280234] br0: port 1(vlan1) entered forwarding state [ 17.284751] device br0 left promiscuous mode [ 17.293000] device br0 entered promiscuous mode ifconfig: ioctl 0x8914 failed: Address not available [ 17.305194] device br0 left promiscuous mode ath9k deconfigure_single: phy0 ath0 ath9k deconfigure_single: phy1 ath1 ath9k configure_single: phy0 ath0 sh: can't create /sys/kernel/debug/ieee80211/phy0/ath9k/chanbw: nonexistent directory [ 21.462762] Core CLK 300 [ 21.462787] Mac CLK 150 setup ath0 C0:56:27:08:B2:94 Configuration file: /tmp/ath0_hostap.conf [ 23.474026] br0: port 2(ath0) entered blocking state [ 23.474050] br0: port 2(ath0) entered disabled state [ 23.478240] device ath0 entered promiscuous mode ath0: interface state UNINITIALIZED->COUNTRY_UPDATE Using interface ath0 with hwaddr c0:56:27:08:b2:94 and ssid "dd-wrt" [ 24.035555] br0: port 2(ath0) entered blocking state [ 24.035579] br0: port 2(ath0) entered forwarding state ath0: interface state COUNTRY_UPDATE->ENABLED ath0: AP-ENABLED ath9k configure_single: phy1 ath1 sh: can't create /sys/kernel/debug/ieee80211/phy1/ath9k/chanbw: nonexistent directory [ 24.097748] Core CLK 300 [ 24.097770] Mac CLK 150 setup ath1 C0:56:27:08:B2:95 Configuration file: /tmp/ath1_hostap.conf [ 25.511711] br0: port 3(ath1) entered blocking state [ 25.511740] br0: port 3(ath1) entered disabled state [ 25.516023] device ath1 entered promiscuous mode ath1: interface state UNINITIALIZED->COUNTRY_UPDATE Using interface ath1 with hwaddr c0:56:27:08:b2:95 and ssid "dd-wrt" [ 25.960155] br0: port 3(ath1) entered blocking state [ 25.960182] br0: port 3(ath1) entered forwarding state ath1: interface state COUNTRY_UPDATE->ENABLED ath1: AP-ENABLED killall: roaming_daemon: no process killed route: ioctl 0x890c failed: No such process route: ioctl 0x890b failed: Network unreachable route: ioctl 0x890c failed: No such process route: ioctl 0x890b failed: Network unreachable sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max: nonexistent directory sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max_hyst: nonexistent directory cp: can't stat '/tmp/mycron.d/*': No such file or directory cp: can't stat '/jffs/mycron.d/*': No such file or directory cp: can't stat '/mmc/mycron.d/*': No such file or directory [ 26.241022] fast-classifier: starting up [ 26.241126] fast-classifier: registered [ 26.252697] device vlan2 entered promiscuous mode rmmod: eoip: No such file or directory cat: can't open '/proc/net/ip_conntrack_flush': No such file or directory 0 cannot open /proc/sys/net/ipv4/conf/br0/loop [ 26.905626] device vlan2 left promiscuous mode ath9k radio 1: phy0 ath0 udhcpc: started, v1.30.0 ath9k radio 1: phy1 ath1 cannot open /proc/sys/dev/wifi0/silent cannot open /proc/sys/dev/wifi1/silent udhcpc: sending discover /opt/etc/init.d/rcS: No such file or directory /jffs/etc/init.d/rcS: No such file or directory /mmc/etc/init.d/rcS: No such file or directory killall: proxywatchdog.sh: no process killed /mnt/smbshare umount: can't unmount /mnt/smbshare: No such file or directory rmmod: cifs: No such file or directory rmmod: fscache: No such file or directory killall: schedulerb.sh: no process killed killall: shatd: no process killed killall: wdswatchdog.sh: no process killed The Milkfish Router Services ERROR: Necessary service setting not found: milkfish_username - aborting. The Milkfish Router Services Restoring SIP ddsubscriber database from NVRAM... Empty. The Milkfish Router Services Restoring SIP ddaliases database from NVRAM... Empty. udhcpc: sending discover udhcpc: sending discover