DD-WRT v3.0-r31101 std (c) 2017 NewMedia-NET GmbH Release: 01/07/17 ========================================================== ___ ___ _ _____ ______ ____ ___ / _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \ / // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // / /____/____/ |__/|__/_/|_| /_/ |___/____(_)___/ DD-WRT v3.0 http://www.dd-wrt.com ========================================================== BusyBox v1.24.2 (2017-01-07 00:04:57 CET) built-in shell (ash) root@---:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.18.45 (root@seg-desktop) (gcc version 6.1.0 (LEDE GCC 6.1.0 r1009) ) #117 SMP PREEMPT Wed Dec 28 00:41:18 CET 2016 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: Linksys EA8500 WiFi Router [ 0.000000] Ignoring memory range 0x41500000 - 0x42000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 122880 [ 0.000000] free_area_init_node: node 0, pgdat c071e800, node_mem_map ddb40000 [ 0.000000] Normal zone: 960 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 122880 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 9 pages/cpu @ddfd3000 s7552 r8192 d21120 u36864 [ 0.000000] pcpu-alloc: s7552 r8192 d21120 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:16 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 481228K/491520K available (3854K kernel code, 279K rwdata, 1104K rodata, 184K init, 403K bss, 10292K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff000000 ( 520 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc06dfe1c (4960 kB) [ 0.000000] .init : 0xc06e0000 - 0xc070e000 ( 184 kB) [ 0.000000] .data : 0xc070e000 - 0xc0753e04 ( 280 kB) [ 0.000000] .bss : 0xc0753e04 - 0xc07b8b84 ( 404 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000012] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 687194767200ns [ 0.000027] Switching to timer-based delay loop, resolution 160ns [ 0.000429] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000452] pid_max: default: 32768 minimum: 301 [ 0.000693] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000709] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001349] CPU: Testing write buffer coherency: ok [ 0.001613] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002108] Setting up static identity map for 0x42213180 - 0x422131d8 [ 0.063436] CPU1: Booted secondary processor [ 0.063566] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.063684] Brought up 2 CPUs [ 0.063708] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.063719] CPU: All CPU(s) started in SVC mode. [ 0.078490] VFP support v0.3: implementor 51 architecture 0 part 4d variant 2 rev 0 [ 0.079029] pinctrl core: initialized pinctrl subsystem [ 0.089421] NET: Registered protocol family 16 [ 0.089742] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.113853] cpuidle: using governor ladder [ 0.144869] cpuidle: using governor menu [ 0.163903] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 0.163991] qcom_rpm 108000.rpm: failed to mark ack irq as wakeup [ 0.164048] qcom_rpm 108000.rpm: failed to mark wakeup irq as wakeup [ 0.199488] pps_core: LinuxPPS API ver. 1 registered [ 0.199502] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.199545] PTP clock support registered [ 0.200682] pcie_init: pcie_init: unable to create IPC log context for pcie0-short [ 0.200695] pcie_init: pcie_init: unable to create IPC log context for pcie0-long [ 0.200706] pcie_init: pcie_init: unable to create IPC log context for pcie1-short [ 0.200716] pcie_init: pcie_init: unable to create IPC log context for pcie1-long [ 0.201119] Switched to clocksource dg_timer [ 0.202534] NET: Registered protocol family 2 [ 0.203235] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.203272] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.203325] TCP: Hash tables configured (established 4096 bind 4096) [ 0.203369] TCP: reno registered [ 0.203390] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.203410] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.203646] NET: Registered protocol family 1 [ 0.203718] PCI: CLS 0 bytes, default 64 [ 0.204849] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.204942] Crashlog allocated RAM at address 0x5ff00000 [ 0.205811] squashfs: version 3.0 (2006/03/15) Phillip Lougher [ 0.205848] msgmni has been set to 939 [ 0.208202] io scheduler noop registered [ 0.208227] io scheduler deadline registered (default) [ 0.209587] 1b500000.pci supply vdda not found, using dummy regulator [ 0.209677] 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.209754] 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.240736] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.240759] pci_bus 0000:00: root bus resource [io 0xfe00000-0xfffff] (bus address [0x1fc00000-0xfefffff]) [ 0.240775] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.240792] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.240841] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.240979] pci 0000:00:00.0: supports D1 [ 0.240993] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.241383] PCI: bus0: Fast back to back transfers disabled [ 0.241725] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000 [ 0.241931] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.242874] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.243300] PCI: bus1: Fast back to back transfers disabled [ 0.243320] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.243471] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.243494] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.243607] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.243628] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.244075] aer 0000:00:00.0:pcie02: service driver aer loaded [ 0.244424] 1b700000.pci supply vdda not found, using dummy regulator [ 0.244506] 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.244596] 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.274817] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.274837] pci_bus 0001:00: root bus resource [io 0x31e10000-0xfffff] (bus address [0x63c00000-0x31eeffff]) [ 0.274852] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.274868] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.274912] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.275029] pci 0001:00:00.0: supports D1 [ 0.275043] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 0.275356] PCI: bus0: Fast back to back transfers disabled [ 0.275687] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000 [ 0.275885] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.276823] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 0.277239] PCI: bus1: Fast back to back transfers disabled [ 0.277257] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.277470] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.277492] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.277599] pci 0001:00:00.0: PCI bridge to [bus 01] [ 0.277617] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.278007] aer 0001:00:00.0:pcie02: service driver aer loaded [ 0.278337] 1b900000.pci supply vdda not found, using dummy regulator [ 0.278419] 1b900000.pci supply vdda_phy not found, using dummy regulator [ 0.278497] 1b900000.pci supply vdda_refclk not found, using dummy regulator [ 0.413309] qcom-pcie 1b900000.pci: link initialization failed [ 0.415416] qcom-pcie 1b900000.pci: PCI host bridge to bus 0002:00 [ 0.415436] pci_bus 0002:00: root bus resource [io 0x35e20000-0xfffff] (bus address [0x6bc00000-0x35edffff]) [ 0.415451] pci_bus 0002:00: root bus resource [mem 0x32000000-0x35dfffff] [ 0.415473] pci_bus 0002:00: root bus resource [bus 00-ff] [ 0.415524] PCI: bus0: Fast back to back transfers enabled [ 0.418030] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.419344] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.420325] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.420424] msm_serial 16340000.serial: uartclk = 1843200 [ 0.420479] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 184, base_baud = 115200) is a MSM [ 0.420533] msm_serial: console setup on port #0 [ 1.132570] console [ttyMSM0] enabled [ 1.137355] msm_serial: driver initialized [ 1.144143] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1 [ 1.144632] nand: AMD/Spansion S34MS01G2 [ 1.151140] nand: 128MiB, SLC, page size: 2048, OOB size: 64 [ 1.155137] Scanning device for bad blocks [ 1.600327] random: nonblocking pool is initialized [ 1.924429] 19 ofpart partitions found on MTD device qcom-nandc [ 1.924459] Creating 19 MTD partitions on "qcom-nandc": [ 1.929157] 0x000000000000-0x000000040000 : "SBL1" [ 1.935349] 0x000000040000-0x000000180000 : "MIBIB" [ 1.940011] 0x000000180000-0x0000002c0000 : "SBL2" [ 1.944821] 0x0000002c0000-0x000000540000 : "SBL3" [ 1.949602] 0x000000540000-0x000000660000 : "DDRCONFIG" [ 1.954470] 0x000000660000-0x000000780000 : "SSD" [ 1.959517] 0x000000780000-0x000000a00000 : "TZ" [ 1.964462] 0x000000a00000-0x000000c80000 : "RPM" [ 1.969088] 0x000000c80000-0x000000dc0000 : "art" [ 1.973734] 0x000000dc0000-0x000000ec0000 : "APPSBL" [ 1.978368] 0x000000ec0000-0x000000f00000 : "u_env" [ 1.983477] 0x000000f00000-0x000000f40000 : "s_env" [ 1.988018] 0x000000f40000-0x000000f80000 : "devinfo" [ 1.992915] 0x000000f80000-0x000003780000 : "linux" [ 1.998106] 0x000001280000-0x000003780000 : "rootfs" [ 2.002867] mtd: partition "rootfs" set to be root filesystem [ 2.007197] 0x000003780000-0x000005f40000 : "linux2" [ 2.013711] 0x000003a80000-0x000005f40000 : "rootfs2" [ 2.018696] 0x000005f40000-0x000005f80000 : "nvram" [ 2.023661] 0x000005f80000-0x000008000000 : "ddwrt" [ 2.029564] IMQ: autocreate imq0 NS c074e0c0 [ 2.032999] IMQ: autocreate imq1 NS c074e0c0 [ 2.036885] IMQ driver loaded successfully. (numdevs = 16, numqueues = 1) [ 2.041217] Hooking IMQ after NAT on PREROUTING. [ 2.048058] Hooking IMQ before NAT on POSTROUTING. [ 2.053098] libphy: Fixed MDIO Bus: probed [ 2.057778] libphy: GPIO Bitbanged MDIO: probed [ 2.082795] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 2.854541] tun: Universal TUN/TAP device driver, 1.6 [ 2.854566] tun: (C) 1999-2004 Max Krasnyansky [ 2.860011] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.864750] Ring mode enabled [ 2.869761] DMA HW capability register supported [ 2.872798] Enhanced/Alternate descriptors [ 2.877486] Enabled extended descriptors [ 2.881545] RX Checksum Offload Engine supported (type 2) [ 2.885649] TX Checksum insertion supported [ 2.891028] Wake-Up On Lan supported [ 2.895600] Enable RX Mitigation via HW Watchdog Timer [ 2.900256] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.904150] Ring mode enabled [ 2.909257] DMA HW capability register supported [ 2.912284] Enhanced/Alternate descriptors [ 2.916983] Enabled extended descriptors [ 2.920978] RX Checksum Offload Engine supported (type 2) [ 2.925217] TX Checksum insertion supported [ 2.930526] Wake-Up On Lan supported [ 2.935089] Enable RX Mitigation via HW Watchdog Timer [ 2.939194] PPP generic driver version 2.4.2 [ 2.943779] PPP BSD Compression module registered [ 2.948079] PPP Deflate Compression module registered [ 2.952762] PPP MPPE Compression module registered [ 2.957715] NET: Registered protocol family 24 [ 2.962495] PPTP driver version 0.8.5 [ 2.966945] i2c /dev entries driver [ 2.976101] Speed bin: 0 [ 2.976124] PVS bin: 1 [ 2.978107] platform cpufreq-krait.0: Driver cpufreq-krait requests probe deferral [ 2.981894] L2 @ QSB rate. Forcing new rate. [ 2.987650] L2 @ 387500 KHz [ 2.992044] CPU0 @ 800000 KHz [ 2.994362] CPU1 @ QSB rate. Forcing new rate. [ 2.997571] CPU1 @ 384000 KHz [ 3.002220] GACT probability NOT on [ 3.004885] Mirror/redirect action on [ 3.008215] Simple TC action Loaded [ 3.012914] netem: version 1.3 [ 3.015329] u32 classifier [ 3.018404] Performance counters on [ 3.021097] input device check on [ 3.024911] Actions configured [ 3.028691] Netfilter messages via NETLINK v0.30. [ 3.032094] nf_conntrack version 0.5.0 (7519 buckets, 30076 max) [ 3.037056] nf_conntrack_rtsp v0.7 loading [ 3.043374] xt_time: kernel timezone is -0000 [ 3.046734] ip_set: protocol 6 [ 3.051582] gre: GRE over IPv4 demultiplexor driver [ 3.054338] nf_nat_rtsp v0.7 loading [ 3.058904] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.063037] TCP: bic registered [ 3.067984] TCP: cubic registered [ 3.070848] TCP: westwood registered [ 3.074403] TCP: highspeed registered [ 3.077965] TCP: hybla registered [ 3.081617] TCP: htcp registered [ 3.084824] TCP: vegas registered [ 3.088125] TCP: veno registered [ 3.091336] TCP: scalable registered [ 3.094707] TCP: lp registered [ 3.098193] TCP: yeah registered [ 3.101057] TCP: illinois registered [ 3.104522] NET: Registered protocol family 17 [ 3.108077] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 3.112390] Bridge firewalling registered [ 3.125104] 8021q: 802.1Q VLAN Support v1.8 [ 3.129049] Registering SWP/SWPB emulation handler [ 3.136898] trying to register driver generic_krait [ 3.137784] Frequency table not initialized. [ 3.142748] Frequency table not initialized. [ 3.147089] Frequency table not initialized. [ 3.151309] Frequency table not initialized. [ 3.155648] Frequency table not initialized. [ 3.161399] Frequency table not initialized. [ 3.164131] Frequency table not initialized. [ 3.168338] Frequency table not initialized. [ 3.172637] Frequency table not initialized. [ 3.176827] Frequency table not initialized. [ 3.181094] driver generic_krait up and running [ 3.185424] searching for nvram [ 3.189609] nvram size = -1066983986 [ 3.213588] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 3.221191] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19 [ 3.223996] VFS: Mounted root (squashfs filesystem) readonly on device 31:16. [ 3.227814] Freeing unused kernel memory: 184K (c06e0000 - c070e000) [ 5.526556] UBIFS error (pid 710): ubifs_mount: cannot open "ubi0:rootfs_data", error -19 [ 6.708005] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6 [ 6.708039] Backport generated by backports.git backports-20160324-9-g0e38f5c [ 7.250792] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 7.251385] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 7.383683] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2 [ 7.383735] ath10k_pci 0000:01:00.0: Falling back to user helper [ 7.691550] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 7.691587] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 7.701431] ath10k_pci 0000:01:00.0: firmware ver 10.4.3.00063 api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce [ 7.710627] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 7.731859] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 62700264 [ 8.515771] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 8.621509] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 8.910391] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 8.980063] ath: EEPROM regdomain: 0x0 [ 8.980087] ath: EEPROM indicates default country code should be used [ 8.980104] ath: doing EEPROM country->regdmn map search [ 8.980129] ath: country maps to regdmn code: 0x3a [ 8.980148] ath: Country alpha2 being used: US [ 8.980165] ath: Regpair used: 0x3a [ 8.994322] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 8.994924] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 9.123414] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2 [ 9.123456] ath10k_pci 0001:01:00.0: Falling back to user helper [ 9.134551] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 9.139173] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 9.151146] ath10k_pci 0001:01:00.0: firmware ver 10.4.3.00063 api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce [ 9.156899] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 9.166938] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 62700264 [ 10.358033] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 10.426504] ath: EEPROM regdomain: 0x0 [ 10.426520] ath: EEPROM indicates default country code should be used [ 10.426530] ath: doing EEPROM country->regdmn map search [ 10.426545] ath: country maps to regdmn code: 0x3a [ 10.426557] ath: Country alpha2 being used: US [ 10.426566] ath: Regpair used: 0x3a [ 10.594630] usbcore: registered new interface driver usbfs [ 10.594990] usbcore: registered new interface driver hub [ 10.599212] usbcore: registered new device driver usb [ 10.635049] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.642806] ehci-platform: EHCI generic platform driver [ 10.661129] ehci-pci: EHCI PCI platform driver [ 10.717161] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 10.990321] soc:usb30@0 supply gdsc not found, using dummy regulator [ 10.991222] platform 11000000.dwc3: Driver dwc3 requests probe deferral [ 10.996150] platform 11000000.dwc3: Driver dwc3 requests probe deferral [ 11.002262] soc:usb30@1 supply gdsc not found, using dummy regulator [ 11.009505] platform 10000000.dwc3: Driver dwc3 requests probe deferral [ 11.015671] platform 11000000.dwc3: Driver dwc3 requests probe deferral [ 11.022680] platform 10000000.dwc3: Driver dwc3 requests probe deferral [ 11.056516] 100f8800.phy supply vddcx not found, using dummy regulator [ 11.056580] 100f8800.phy supply v3p3 not found, using dummy regulator [ 11.062030] 100f8800.phy supply v1p8 not found, using dummy regulator [ 11.068480] 100f8800.phy supply vbus not found, using dummy regulator [ 11.075036] 110f8800.phy supply vddcx not found, using dummy regulator [ 11.075258] platform 11000000.dwc3: Driver dwc3 requests probe deferral [ 11.075477] platform 10000000.dwc3: Driver dwc3 requests probe deferral [ 11.094325] 110f8800.phy supply v3p3 not found, using dummy regulator [ 11.100860] 110f8800.phy supply v1p8 not found, using dummy regulator [ 11.107509] 110f8800.phy supply vbus not found, using dummy regulator [ 11.122512] platform 11000000.dwc3: Driver dwc3 requests probe deferral [ 11.122786] platform 10000000.dwc3: Driver dwc3 requests probe deferral [ 11.136817] 100f8830.phy supply vddcx not found, using dummy regulator [ 11.136927] 100f8830.phy supply v1p8 not found, using dummy regulator [ 11.142456] qcom-dwc3-ssphy 100f8830.phy: cannot get HSIO settings from device node, using default values [ 11.149030] platform 11000000.dwc3: Driver dwc3 requests probe deferral [ 11.158518] 110f8830.phy supply vddcx not found, using dummy regulator [ 11.165244] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for vddcx [ 11.171324] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for v3p3 [ 11.171540] 110f8830.phy supply v1p8 not found, using dummy regulator [ 11.171585] qcom-dwc3-ssphy 110f8830.phy: cannot get HSIO settings from device node, using default values [ 11.190776] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for v1p8 [ 11.202885] qcom-dwc3-ssphy 100f8830.phy: cannot set voltage for vddcx [ 11.442325] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 11.442403] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 11.446884] xhci-hcd xhci-hcd.0.auto: irq 237, io mem 0x10000000 [ 11.456403] hub 1-0:1.0: USB hub found [ 11.460544] hub 1-0:1.0: 1 port detected [ 11.465275] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 11.468165] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 11.474972] hub 2-0:1.0: USB hub found [ 11.481275] hub 2-0:1.0: 1 port detected [ 11.485780] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for vddcx [ 11.489271] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for v3p3 [ 11.495296] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for v1p8 [ 11.504227] qcom-dwc3-ssphy 110f8830.phy: cannot set voltage for vddcx [ 11.742415] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 11.742468] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 11.746983] xhci-hcd xhci-hcd.1.auto: irq 142, io mem 0x11000000 [ 11.755837] hub 3-0:1.0: USB hub found [ 11.760629] hub 3-0:1.0: 1 port detected [ 11.765074] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 11.768255] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 11.774988] hub 4-0:1.0: USB hub found [ 11.781116] hub 4-0:1.0: 1 port detected [ 12.081602] usb 3-1: new high-speed USB device number 2 using xhci-hcd [ 16.193599] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 16.193680] usb usb4: USB disconnect, device number 1 [ 16.201407] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered [ 16.202870] xhci-hcd xhci-hcd.1.auto: remove, state 1 [ 16.208444] usb usb3: USB disconnect, device number 1 [ 16.224575] usb 3-1: USB disconnect, device number 2 [ 16.234460] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered [ 16.234648] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 16.251872] usb usb2: USB disconnect, device number 1 [ 16.255292] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered [ 16.255941] xhci-hcd xhci-hcd.0.auto: remove, state 1 [ 16.267450] usb usb1: USB disconnect, device number 1 [ 16.269235] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered [ 16.282521] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 16.282609] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 16.287073] xhci-hcd xhci-hcd.0.auto: irq 237, io mem 0x10000000 [ 16.295800] hub 1-0:1.0: USB hub found [ 16.300850] hub 1-0:1.0: 1 port detected [ 16.305106] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 16.308359] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 16.315054] hub 2-0:1.0: USB hub found [ 16.321328] hub 2-0:1.0: 1 port detected [ 16.325930] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 16.329113] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 16.334747] xhci-hcd xhci-hcd.1.auto: irq 142, io mem 0x11000000 [ 16.343176] hub 3-0:1.0: USB hub found [ 16.348327] hub 3-0:1.0: 1 port detected [ 16.352616] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 16.355871] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 16.362513] hub 4-0:1.0: USB hub found [ 16.368806] hub 4-0:1.0: 1 port detected [ 16.404354] SCSI subsystem initialized [ 16.492134] usbcore: registered new interface driver usb-storage [ 16.568796] libata version 3.00 loaded. [ 16.656756] ahci 29000000.sata: forcing port_map 0x0 -> 0x1 [ 16.656810] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 16.661139] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst [ 16.670718] scsi host0: ahci_platform [ 16.678050] usb 3-1: new high-speed USB device number 2 using xhci-hcd [ 16.683389] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241 [ 16.826177] usb-storage 3-1:1.0: USB Mass Storage device detected [ 16.826519] scsi host1: usb-storage 3-1:1.0 [ 17.031587] ata1: SATA link down (SStatus 0 SControl 300) [ 17.843948] scsi 1:0:0:0: Direct-Access PNY USB 2.0 FD 0.00 PQ: 0 ANSI: 2 [ 17.848645] sd 1:0:0:0: [sda] 31711232 512-byte logical blocks: (16.2 GB/15.1 GiB) [ 17.851889] sd 1:0:0:0: [sda] Write Protect is off [ 17.858648] sd 1:0:0:0: [sda] Mode Sense: 00 00 00 00 [ 17.859180] sd 1:0:0:0: [sda] Asking for cache data failed [ 17.863343] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 17.871889] sda: sda1 [ 17.886230] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 18.090710] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 18.098645] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 18.954371] device br0 entered promiscuous mode [ 19.022692] device vlan1 entered promiscuous mode [ 19.022724] device eth0 entered promiscuous mode [ 19.026450] br0: port 1(vlan1) entered forwarding state [ 19.031092] br0: port 1(vlan1) entered forwarding state [ 19.043572] device br0 left promiscuous mode [ 19.046931] device br0 entered promiscuous mode [ 19.106827] device br0 left promiscuous mode [ 21.021499] br0: port 1(vlan1) entered forwarding state [ 24.894918] device ath0 entered promiscuous mode [ 27.088474] br0: port 2(ath0) entered forwarding state [ 27.088552] br0: port 2(ath0) entered forwarding state [ 28.696680] device ath1 entered promiscuous mode [ 29.081499] br0: port 2(ath0) entered forwarding state [ 29.415620] br0: port 3(ath1) entered forwarding state [ 29.415671] br0: port 3(ath1) entered forwarding state [ 30.039795] device vlan2 entered promiscuous mode [ 30.973471] device vlan2 left promiscuous mode [ 31.411473] br0: port 3(ath1) entered forwarding state [ 312.019055] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead. root@---:~# ps PID USER VSZ STAT COMMAND 1 root 1388 S /sbin/init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 5 root 0 SW< [kworker/0:0H] 6 root 0 SW [kworker/u4:0] 7 root 0 SW [rcu_preempt] 8 root 0 SW [rcu_sched] 9 root 0 SW [rcu_bh] 10 root 0 SW [migration/0] 11 root 0 SW [migration/1] 12 root 0 SW [ksoftirqd/1] 14 root 0 SW< [kworker/1:0H] 15 root 0 SW< [khelper] 16 root 0 SW< [writeback] 18 root 0 SW< [crypto] 19 root 0 SW< [bioset] 20 root 0 SW< [kblockd] 21 root 0 SW [kswapd0] 22 root 0 SW [fsnotify_mark] 31 root 0 SW [kworker/u4:1] 34 root 0 SW [kworker/1:1] 43 root 0 SW< [deferwq] 44 root 0 SW [kworker/0:2] 45 root 0 SW [kworker/1:2] 689 root 692 S /sbin/hotplug2 --set-rules-file /etc/hotplug2.rules --persistent 747 root 0 SW< [cfg80211] 757 root 0 SW< [ath10k_wq] 758 root 0 SW< [ath10k_aux_wq] 761 root 0 SW< [ath10k_wq] 762 root 0 SW< [ath10k_aux_wq] 864 root 0 SW< [ata_sff] 869 root 0 SW [scsi_eh_0] 870 root 0 SW< [scsi_tmf_0] 872 root 0 SW [scsi_eh_1] 873 root 0 SW< [scsi_tmf_1] 874 root 0 SW [usb-storage] 886 root 0 SW< [kworker/1:1H] 1074 root 2816 S /usr/sbin/smbd -D --configfile=/tmp/smb.conf 1076 root 2616 S /usr/sbin/nmbd -D --configfile=/tmp/smb.conf 1096 root 2200 S hostapd -B -P /var/run/ath0_hostapd.pid /tmp/ath0_hostap.conf 1122 root 2200 S hostapd -B -P /var/run/ath1_hostapd.pid /tmp/ath1_hostap.conf 1208 root 1072 S telnetd 1255 root 844 S dnsmasq -u root -g root --conf-file=/tmp/dnsmasq.conf --cache-size=1500 --dhcp-option=252," " 1281 root 788 S dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p xxxxx -s 1287 root 0 SW< [kworker/0:1H] 1568 root 1792 S ttraff 1624 root 1584 S resetbutton 1629 root 1072 S syslogd -L 1632 root 1072 S klogd 2007 root 3992 S httpd -p 80 2527 root 1584 S process_monitor 3786 root 1536 S wland 3787 root 1072 S udhcpc -i vlan2 -p /var/run/udhcpc.pid -s /tmp/udhcpc -O routes -O msstaticroutes -O staticroutes 3884 root 668 S cron 3893 root 7144 S unbound -c /tmp/unbound.conf 6247 root 0 SW [kworker/0:1] 7156 root 0 SW [kworker/0:0] 7311 root 860 S dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p xxxxx -s 7312 root 1076 S -sh 7315 root 1072 R ps root@---:~# lsmod Module Size Used by xt_IMQ 718 2 nf_nat_pptp 1464 0 nf_conntrack_pptp 3082 1 nf_nat_pptp nf_nat_proto_gre 797 1 nf_nat_pptp nf_conntrack_proto_gre 2763 1 nf_conntrack_pptp xt_opendpi 269207 1865 xt_physdev 1290 0 xt_DSCP 1435 1 xt_dscp 1100 1 msdos 5515 0 vfat 7888 1 fat 43951 2 msdos,vfat nls_utf8 826 1 nls_iso8859_2 3402 0 nls_iso8859_1 2890 0 nls_cp437 4422 1 ahci_platform 2163 0 ahci 13855 0 libahci_platform 4496 1 ahci_platform libahci 17799 2 ahci,libahci_platform libata 121852 4 ahci_platform,ahci,libahci_platform,libahci usb_storage 36213 1 sd_mod 26691 2 scsi_mod 85045 3 libata,usb_storage,sd_mod xhci_plat_hcd 3627 0 phy_qcom_ssusb 3524 2 phy_qcom_hsusb 3000 2 dwc3_qcom 1797 0 dwc3 15983 0 xhci_pci 2852 0 xhci_hcd 84926 2 xhci_plat_hcd,xhci_pci,[permanent] ohci_hcd 25093 0 ehci_pci 2638 0 ehci_platform 4220 0 ehci_hcd 35655 2 ehci_pci,ehci_platform usbcore 129768 9 usb_storage,xhci_plat_hcd,xhci_pci,xhci_hcd,ohci_hcd,ehci_pci,ehci_platform,ehci_hcd usb_common 1593 2 dwc3,usbcore nls_base 4984 7 vfat,fat,nls_utf8,nls_iso8859_2,nls_iso8859_1,nls_cp437,usbcore ath10k_pci 29587 0 ath10k_core 261490 1 ath10k_pci ath9k 85289 0 ath9k_common 19606 1 ath9k ath9k_hw 333659 2 ath9k,ath9k_common ath 14311 4 ath10k_core,ath9k,ath9k_common,ath9k_hw mac80211 320991 3 ath10k_core,ath9k,ath9k_hw cfg80211 216056 5 ath10k_core,ath9k,ath9k_common,ath,mac80211 compat 13579 6 ath10k_pci,ath10k_core,ath9k,ath9k_common,mac80211,cfg80211 qcom_wdt 2396 0 leds_gpio 2819 0 leds_tlc59116 2200 0 regmap_i2c 1578 1 leds_tlc59116 root@---:~# tc filter show dev imq0 filter parent 1: protocol ip pref 49138 u32 filter parent 1: protocol ip pref 49138 u32 fh 80e: ht divisor 1 root@---:~# tc -d class show dev imq0 class hfsc 1:213 parent 1:210 leaf 213: sc m1 0bit d 0us m2 1000bit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:212 parent 1:210 leaf 212: sc m1 0bit d 0us m2 2000bit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:100 parent 1:1 leaf 100: sc m1 0bit d 0us m2 14076Kbit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:10 parent 1:1 leaf 10: sc m1 0bit d 0us m2 9384Kbit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:211 parent 1:210 leaf 211: sc m1 0bit d 0us m2 3000bit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:30 parent 1:1 leaf 30: sc m1 0bit d 0us m2 2815Kbit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:210 parent 1:1 sc m1 0bit d 0us m2 5000bit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:220 parent 1:1 sc m1 0bit d 0us m2 5000bit ul m1 0bit d 0us m2 18768Kbit class hfsc 1: root class hfsc 1:221 parent 1:220 leaf 221: sc m1 0bit d 0us m2 3000bit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:1 parent 1: sc m1 0bit d 0us m2 18768Kbit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:222 parent 1:220 leaf 222: sc m1 0bit d 0us m2 2000bit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:2 parent 1:1 sc m1 0bit d 0us m2 14076Kbit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:20 parent 1:1 leaf 20: sc m1 0bit d 0us m2 4692Kbit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:223 parent 1:220 leaf 223: sc m1 0bit d 0us m2 1000bit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:3 parent 1:1 sc m1 0bit d 0us m2 9384Kbit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:4 parent 1:1 sc m1 0bit d 0us m2 4692Kbit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:40 parent 1:1 leaf 40: sc m1 0bit d 0us m2 938000bit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:5 parent 1:1 sc m1 0bit d 0us m2 2815Kbit ul m1 0bit d 0us m2 18768Kbit class hfsc 1:6 parent 1:1 sc m1 0bit d 0us m2 938000bit ul m1 0bit d 0us m2 18768Kbit root@---:~# uptime 14:00:09 up 25 min, load average: 0.08, 0.11, 0.08 root@---:~# exit