U-Boot 2012.07 [Standard IPQ806X.LN,r40331] (Mar 16 2015 - 16:29:21) CBT U-Boot ver: 1.0.9 smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:0:3:7f:ba:db:2 eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is 00:06:3b:01:41:00 , eth1 Updating boot_count ... done Hit any key to stop autoboot: 0 Write Reg: 0x00000660: Oldval = 0x00140020 Newval = 0x0014007e Write Reg: 0x0000066c: Oldval = 0x0014005c Newval = 0x0014007d Write Reg: 0x00000678: Oldval = 0x0014005a Newval = 0x0014007b Write Reg: 0x00000684: Oldval = 0x00140056 Newval = 0x00140077 Write Reg: 0x00000690: Oldval = 0x0014004e Newval = 0x0014006f Write Reg: 0x0000069c: Oldval = 0x00140001 Newval = 0x0014005f Write Reg: 0x000006a8: Oldval = 0x0014001e Newval = 0x0014003f Write Reg: 0x00000420: Oldval = 0x00020001 Newval = 0x00010001 Write Reg: 0x00000428: Oldval = 0x00010001 Newval = 0x00010001 Write Reg: 0x00000430: Oldval = 0x00010001 Newval = 0x00010001 Write Reg: 0x00000438: Oldval = 0x00010001 Newval = 0x00010001 Write Reg: 0x00000440: Oldval = 0x00010001 Newval = 0x00010001 Write Reg: 0x00000448: Oldval = 0x00020001 Newval = 0x00010001 Write Reg: 0x00000450: Oldval = 0x00010001 Newval = 0x00010001 (IPQ) # (IPQ) # printenv altkern=3780000 auto_recovery=yes baudrate=115200 boot_part=1 boot_part_ready=3 boot_ver=1.0.9 bootargs=console=ttyHSL1,115200n8 bootcmd=bootipq bootdelay=2 ethact=eth0 ethaddr=00:06:3b:01:41:00 flashimg=tftp $loadaddr $image;nand erase $prikern $filesize;nand write $loadadd r $prikern $filesize flashimg2=tftp $loadaddr $image;nand erase $altkern $filesize;nand write $loadad dr $altkern $filesize image=wraith.bin ipaddr=192.168.1.1 loadaddr=42000000 machid=1260 netmask=255.255.255.0 partbootargs=console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=3 1:14 partbootargs2=console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root= 31:16 serverip=192.168.1.254 stderr=serial stdin=serial stdout=serial Environment size: 770/262140 bytes (IPQ) # reset resetting ... Resetting with watch dog! U-Boot 2012.07 [Standard IPQ806X.LN,r40331] (Mar 16 2015 - 16:29:21) CBT U-Boot ver: 1.0.9 smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:0:3:7f:ba:db:2 eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is 00:06:3b:01:41:00 , eth1 Updating boot_count ... done Hit any key to stop autoboot: 0 MMC Device 0 not found MMC Device 0 not found Loading from nand0, offset 0xf80000 Image Name: DD-WRT V3.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2228095 Bytes = 2.1 MiB Load Address: 42208000 Entry Point: 42208000 Automatic boot of image at addr 0x44000000 ... Image Name: DD-WRT V3.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2228095 Bytes = 2.1 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK Loading Kernel Image ... OK OK mtdids not defined, no default present info: "mtdparts" not set Using machid 0x1260 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.135 (bluebat@helios) (gcc version 6.3.0 (LEDE G CC 6.3.0 r4639-eb43a817f7) ) #232 SMP PREEMPT Mon Oct 22 02:10:08 CEST 2018 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt:Machine model: Linksys EA8500 WiFi Router [ 0.000000] OF: fdt:Ignoring memory range 0x41500000 - 0x42000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 13 pages/cpu @ddc06000 s21324 r8192 d23732 u5324 8 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 121920 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:1 4 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 478140K/491520K available (5120K kernel code, 281K rwdata , 1060K rodata, 1024K init, 399K bss, 13380K reserved, 0K cma-reserved, 0K highm em) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0800000 (6112 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b464b0 ( 282 kB) [ 0.000000] .bss : 0xc0b48000 - 0xc0babf38 ( 400 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, m ax_idle_ns: 305801671480 ns [ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 34359 7383600ns [ 0.000024] Switching to timer-based delay loop, resolution 160ns [ 0.000208] Calibrating delay loop (skipped), value calculated using timer fr equency.. 12.50 BogoMIPS (lpj=62500) [ 0.000232] pid_max: default: 32768 minimum: 301 [ 0.000327] Security Framework initialized [ 0.000390] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000407] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001002] CPU: Testing write buffer coherency: ok [ 0.001311] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001365] Setting up static identity map for 0x42300000 - 0x42300034 [ 0.176940] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.177152] Brought up 2 CPUs [ 0.177176] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.177187] CPU: All CPU(s) started in SVC mode. [ 0.189945] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.190141] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.190168] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.190253] pinctrl core: initialized pinctrl subsystem [ 0.191603] NET: Registered protocol family 16 [ 0.191951] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.217343] cpuidle: using governor ladder [ 0.248361] cpuidle: using governor menu [ 0.301345] msm_bus_fabric_init_driver [ 0.302295] pps_core: LinuxPPS API ver. 1 registered [ 0.302313] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti [ 0.302347] PTP clock support registered [ 0.304036] clocksource: Switched to clocksource dg_timer [ 0.308350] NET: Registered protocol family 2 [ 0.309236] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.309280] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.309335] TCP: Hash tables configured (established 4096 bind 4096) [ 0.309387] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.309412] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.309596] NET: Registered protocol family 1 [ 0.320877] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.327959] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.335425] io scheduler noop registered [ 0.335443] io scheduler deadline registered (default) [ 0.337201] 1b500000.pci supply vdda not found, using dummy regulator [ 0.337310] 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.337409] 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.338218] OF: PCI: host bridge /soc/pci@1b500000 ranges: [ 0.338258] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.338285] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.446528] qcom-pcie 1b500000.pci: link up [ 0.446721] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.446744] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.446764] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus addr ess [0xfe00000-0xfefffff]) [ 0.446780] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.447293] PCI: bus0: Fast back to back transfers disabled [ 0.449694] PCI: bus1: Fast back to back transfers disabled [ 0.449991] pci 0000:00:00.0: BAR 14: assigned [mem 0x08000000-0x081fffff] [ 0.450017] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bi t] [ 0.450152] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.450174] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.451066] 1b700000.pci supply vdda not found, using dummy regulator [ 0.451182] 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.451281] 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.452067] OF: PCI: host bridge /soc/pci@1b700000 ranges: [ 0.452105] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.452127] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.562432] qcom-pcie 1b700000.pci: link up [ 0.562605] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.562625] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.562655] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.563116] PCI: bus0: Fast back to back transfers disabled [ 0.565451] PCI: bus1: Fast back to back transfers disabled [ 0.565843] pci 0001:00:00.0: BAR 14: assigned [mem 0x2e000000-0x2e1fffff] [ 0.565868] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bi t] [ 0.565990] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.566010] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.567396] deviceless supply s1b not found, using dummy regulator [ 0.569448] L2 @ QSB rate. Forcing new rate. [ 0.569620] L2 @ 1200000 KHz [ 0.569769] CPU0 @ 1400000 KHz [ 0.569776] CPU1 @ QSB rate. Forcing new rate. [ 0.569875] CPU1 @ 1400000 KHz [ 0.571207] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.572295] serial8250_init [ 0.572304] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.572940] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.572992] msm_serial 16340000.serial: uartclk = 7372800 [ 0.573029] physical 16340000 = virtual de879000 [ 0.573039] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 168, base_baud = 460800) is a MSM [ 0.573063] msm_serial: console setup on port #0 [ 1.276775] console [ttyMSM0] enabled [ 1.281410] msm_serial: driver initialized [ 1.286182] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1 [ 1.288853] nand: AMD/Spansion S34MS01G2 [ 1.295431] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz e: 64 [ 1.299842] 19 ofpart partitions found on MTD device qcom_nand.0 [ 1.306732] Creating 19 MTD partitions on "qcom_nand.0": [ 1.312816] 0x000000000000-0x000000040000 : "SBL1" [ 1.329349] 0x000000040000-0x000000180000 : "MIBIB" [ 1.341678] 0x000000180000-0x0000002c0000 : "SBL2" [ 1.354047] 0x0000002c0000-0x000000540000 : "SBL3" [ 1.354578] random: fast init done [ 1.370886] 0x000000540000-0x000000660000 : "DDRCONFIG" [ 1.383090] 0x000000660000-0x000000780000 : "SSD" [ 1.395553] 0x000000780000-0x000000a00000 : "TZ" [ 1.399217] 0x000000a00000-0x000000c80000 : "RPM" [ 1.413188] 0x000000c80000-0x000000dc0000 : "art" [ 1.425702] 0x000000dc0000-0x000000ec0000 : "APPSBL" [ 1.437956] 0x000000ec0000-0x000000f00000 : "u_env" [ 1.449333] 0x000000f00000-0x000000f40000 : "s_env" [ 1.460692] 0x000000f40000-0x000000f80000 : "devinfo" [ 1.472064] 0x000000f80000-0x000003780000 : "linux" [ 1.529558] 0x000001280000-0x000003780000 : "rootfs" [ 1.583612] mtd: partition "rootfs" set to be root filesystem [ 1.583637] 0x000003780000-0x000005f40000 : "linux2" [ 1.646039] 0x000003a80000-0x000005f40000 : "rootfs2" [ 1.699803] 0x000005f40000-0x000005f80000 : "nvram" [ 1.711165] 0x000005f80000-0x000008000000 : "ddwrt" [ 1.730026] random: crng init done [ 1.760773] libphy: GPIO Bitbanged MDIO: probed [ 1.763307] libphy: Fixed MDIO Bus: probed [ 1.781875] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 2.631349] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.631369] Ring mode enabled [ 2.635459] DMA HW capability register supported[ 2.638319] Enhanced/Alt ernate descriptors [ 2.643959] Enabled extended descriptors [ 2.646966] RX Checksum Offload Engine supported [ 2.651085] COE Type 2 [ 2.655848] TX Checksum insertion supported [ 2.658029] Wake-Up On Lan supported [ 2.662544] Enable RX Mitigation via HW Watchdog Timer [ 2.667050] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.671140] Ring mode enabled [ 2.676430] DMA HW capability register supported[ 2.679297] Enhanced/Alt ernate descriptors [ 2.685018] Enabled extended descriptors [ 2.687896] RX Checksum Offload Engine supported [ 2.692065] COE Type 2 [ 2.696826] TX Checksum insertion supported [ 2.699009] Wake-Up On Lan supported [ 2.703521] Enable RX Mitigation via HW Watchdog Timer [ 2.707501] i2c /dev entries driver [ 2.712533] Calibration not found. [ 2.715673] qcom-tsens 900000.thermal-sensor: tsens calibration failed [ 2.719416] CPUidle arm: CPU 0 failed to init idle CPU ops [ 2.725845] GACT probability NOT on [ 2.731043] Mirror/redirect action on [ 2.734515] Simple TC action Loaded [ 2.738587] netem: version 1.3 [ 2.741549] u32 classifier [ 2.744748] Performance counters on [ 2.747358] input device check on [ 2.751091] Actions configured [ 2.754971] Netfilter messages via NETLINK v0.30. [ 2.758357] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 2.763910] nf_conntrack_rtsp v0.7 loading [ 2.769282] xt_time: kernel timezone is -0000 [ 2.772974] ip_set: protocol 6 [ 2.777577] gre: GRE over IPv4 demultiplexor driver [ 2.781347] nf_nat_rtsp v0.7 loading [ 2.785219] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.789081] NET: Registered protocol family 17 [ 2.794282] Bridge firewalling registered [ 2.798548] 8021q: 802.1Q VLAN Support v1.8 [ 2.802649] Registering SWP/SWPB emulation handler [ 2.808013] Key type encrypted registered [ 2.818276] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 2.836305] s1a: Bringing 0uV into 1050000-1050000uV [ 2.836480] s1b: Bringing 0uV into 1050000-1050000uV [ 2.840467] s2a: Bringing 0uV into 800000-800000uV [ 2.845530] s2b: Bringing 0uV into 800000-800000uV [ 2.852469] trying to register driver cpufreq-dt [ 2.855801] searching for nvram [ 2.859435] nvram size = 262144 [ 2.897691] no valid UBI magic found inside mtd13[ 2[ 2.905742] VFS: Mo unted root (squashfs filesystem) readonly on device 31:14. [ 2.906932] Freeing unused kernel memory: 1024K start service starting Architecture code for ipq806x cannot open /dev/nvram cannot open /dev/nvram udevtrigger[102]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory sysinit using mac C0:56:27:08:B2:92 mount: mounting ubi0:rootfs_data on /jffs failed: No such device reset boot counter load ATH 802.11 a/b/g Driver insmod: ath_pci.ko: module not found insmod: ath_ahb.ko: module not found load ATH9K 802.11n Driver [ 5.690006] lzma_compress: module license 'unspecified' taints kernel. [ 5.690030] Disabling lock debugging due to kernel taint [ 5.743594] Loading modules backported from Linux version wireless-drivers-ne xt-for-davem-2017-09-01-0-geb464d4a8d09 [ 5.743627] Backport generated by backports.git backports-20160324-111-g97b8d 7c4 load ATH/QCA 802.11ac Driver [ 6.284682] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 6.285357] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 r eset_mode 0 [ 6.456763] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal- pci-0000:01:00.0.bin failed with error -2 [ 6.456798] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.468324] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/ hw2.0/firmware-6.bin failed with error -2 [ 6.472517] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.822885] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 6.822923] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 6.833371] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 feat ures no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 9.136176] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,v endor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/Q CA99X0/hw2.0/board-2.bin [ 9.136417] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 d3e0cd b5 [ 10.347298] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file m ax-sta 512 raw 0 hwcrypto 1 [ 10.454803] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 10.455457] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 r eset_mode 0 [ 10.626826] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal- pci-0001:01:00.0.bin failed with error -2 [ 10.626873] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.638329] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/ hw2.0/firmware-6.bin failed with error -2 [ 10.642592] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.654393] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 10.659260] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 10.672369] ath10k_pci 0001:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 feat ures no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 12.963791] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,v endor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/Q CA99X0/hw2.0/board-2.bin [ 12.963998] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 402a81 11 [ 14.169604] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file m ax-sta 512 raw 0 hwcrypto 1 [ 15.259579] dwmac1000: Master AXI performs any burst length [ 15.259633] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advance d Timestamp supported [ 15.264153] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 15.324130] dwmac1000: Master AXI performs any burst length [ 15.324186] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advance d Timestamp supported [ 15.328860] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [USB] checking... umount: can't unmount /mnt: No such file or directory /etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexis tent directory /etc/preinit: line 45: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_ma x: nonexistent directory /etc/preinit: line 46: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_tc p_timeout_established: nonexistent directory /etc/preinit: line 47: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_ud p_timeout_stream: nonexistent directory cannot open /proc/sys/net/ipv4/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout [ 16.334902] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Ful l - flow control off /etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexis tent directory /etc/preinit: line 45: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_ma x: nonexistent directory /etc/preinit: line 46: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_tc p_timeout_established: nonexistent directory /etc/preinit: line 47: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_ud p_timeout_stream: nonexistent directory cannot open /proc/sys/net/ipv4/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout ath9k deconfigure_single: phy0 ath0 interface wlan0 does not exist! ath9k deconfigure_single: phy1 ath1 interface wlan1 does not exist! [ 17.317218] device br0 entered promiscuous mode killall: ead: no process killed [ 17.377157] br0: port 1(vlan1) entered blocking state [ 17.377188] br0: port 1(vlan1) entered disabled state [ 17.381521] device vlan1 entered promiscuous mode [ 17.386349] device eth0 entered promiscuous mode sh: ead: not found [ 17.399981] br0: port 1(vlan1) entered blocking state [ 17.400011] br0: port 1(vlan1) entered forwarding state [ 17.404673] device br0 left promiscuous mode [ 17.413095] device br0 entered promiscuous mode ifconfig: ioctl 0x8914 failed: Address not available [ 17.429957] device br0 left promiscuous mode ath9k deconfigure_single: phy0 ath0 ath9k deconfigure_single: phy1 ath1 ath9k configure_single: phy0 ath0 sh: write error: Network is down sh: can't create /sys/kernel/debug/ieee80211/phy0/ath9k/chanbw: nonexistent directory call mac80211autochannel for interface: ath0 ath0: freq:2452 qual:98 noise:-99 eirp: 30 ath0: freq:2432 qual:95 noise:-99 eirp: 30 ath0: freq:2412 qual:92 noise:-100 eirp: 30 ath0: freq:2442 qual:73 noise:-99 eirp: 30 ath0: freq:2422 qual:72 noise:-99 eirp: 30 ath0: freq:2462 qual:68 noise:-99 eirp: 30 ath0: freq:2417 qual:48 noise:-100 eirp: 30 ath0: freq:2427 qual:48 noise:-99 eirp: 30 ath0: freq:2437 qual:48 noise:-99 eirp: 30 ath0: freq:2447 qual:48 noise:-99 eirp: 30 ath0: freq:2457 qual:43 noise:-99 eirp: 30 mac80211autochannel interface: ath0 frequency: 2452 setup ath0 C0:56:27:08:B2:94 Configuration file: /tmp/ath0_hostap.conf [ 28.567046] br0: port 2(ath0) entered blocking state [ 28.567069] br0: port 2(ath0) entered disabled state [ 28.571259] device ath0 entered promiscuous mode ath0: interface state UNINITIALIZED->COUNTRY_UPDATE Using interface ath0 with hwaddr c0:56:27:08:b2:94 and ssid "dd-wrt" [ 29.126664] br0: port 2(ath0) entered blocking state [ 29.126693] br0: port 2(ath0) entered forwarding state ath0: interface state COUNTRY_UPDATE->ENABLED ath0: AP-ENABLED ath9k configure_single: phy1 ath1 sh: write error: Network is down sh: can't create /sys/kernel/debug/ieee80211/phy1/ath9k/chanbw: nonexistent directory call mac80211autochannel for interface: ath1 ath1: freq:5825 qual:99 noise:-103 eirp: 30 ath1: freq:5745 qual:94 noise:-103 eirp: 30 ath1: freq:5180 qual:93 noise:-104 eirp: 23 ath1: freq:5200 qual:93 noise:-104 eirp: 23 ath1: freq:5220 qual:93 noise:-104 eirp: 23 ath1: freq:5240 qual:93 noise:-104 eirp: 23 ath1: freq:5260 qual:93 noise:-104 eirp: 23 ath1: freq:5300 qual:93 noise:-104 eirp: 23 ath1: freq:5320 qual:93 noise:-104 eirp: 23 ath1: freq:5620 qual:93 noise:-104 eirp: 23 ath1: freq:5640 qual:93 noise:-104 eirp: 23 ath1: freq:5280 qual:92 noise:-103 eirp: 23 ath1: freq:5500 qual:92 noise:-103 eirp: 23 ath1: freq:5520 qual:92 noise:-103 eirp: 23 ath1: freq:5560 qual:92 noise:-103 eirp: 23 ath1: freq:5580 qual:92 noise:-103 eirp: 23 ath1: freq:5600 qual:92 noise:-103 eirp: 23 ath1: freq:5660 qual:92 noise:-103 eirp: 23 ath1: freq:5680 qual:92 noise:-103 eirp: 23 ath1: freq:5700 qual:92 noise:-103 eirp: 23 ath1: freq:5540 qual:91 noise:-102 eirp: 23 ath1: freq:5720 qual:91 noise:-102 eirp: 23 ath1: freq:5805 qual:79 noise:-86 eirp: 30 ath1: freq:5765 qual:78 noise:-97 eirp: 30 ath1: freq:5785 qual:54 noise:-89 eirp: 30 mac80211autochannel interface: ath1 frequency: 5825 setup ath1 C0:56:27:08:B2:95 Configuration file: /tmp/ath1_hostap.conf ath1: interface state UNINITIALIZED->COUNTRY_UPDATE Using interface ath1 with hwaddr c0:56:27:08:b2:95 and ssid "dd-wrt" ath1: interface state COUNTRY_UPDATE->ENABLED ath1: AP-ENABLED [ 40.399343] br0: port 3(ath1) entered blocking state [ 40.399366] br0: port 3(ath1) entered disabled state [ 40.403606] device ath1 entered promiscuous mode [ 40.408440] br0: port 3(ath1) entered blocking state [ 40.412915] br0: port 3(ath1) entered forwarding state killall: roaming_daemon: no process killed sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max: nonexistent directory sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max_hyst: nonexistent directory cp: can't stat '/tmp/mycron.d/*': No such file or directory cp: can't stat '/jffs/mycron.d/*': No such file or directory[ 40.588362] device vlan2 entered promiscuous mode cp: can't stat '/mmc/mycron.d/*': No such file or directory cat: can't open '/proc/net/ip_conntrack_flush': No such file or directory 0 [ 41.166296] device vlan2 left promiscuous mode ath9k radio 1: phy0 ath0 ath9k radio 1: phy1 ath1 cannot open /proc/sys/dev/wifi0/silent cannot open /proc/sys/dev/wifi1/silent udhcpc: started, v1.29.3 udhcpc: sending discover /opt/etc/init.d/rcS: No such file or directory /jffs/etc/init.d/rcS: No such file or directory /mmc/etc/init.d/rcS: No such file or directory rmmod: eoip: No such file or directory killall: proxywatchdog.sh: no process killed /mnt/smbshare umount: can't unmount /mnt/smbshare: No such file or directory rmmod: cifs: No such file or directory rmmod: fscache: No such file or directory killall: schedulerb.sh: no process killed killall: shatd: no process killed killall: wdswatchdog.sh: no process killed The Milkfish Router Services ERROR: Necessary service setting not found: milkfish_username - aborting. The Milkfish Router Services Restoring SIP ddsubscriber database from NVRAM... Empty. The Milkfish Router Services Restoring SIP ddaliases database from NVRAM... Empty. udhcpc: sending discover udhcpc: sending discover DD-WRT v3.0-r37490M kongat (c) 2018 NewMedia-NET GmbH Release: 10/22/18 DD-WRT login: root Password: ========================================================== ___ ___ _ _____ ______ ____ ___ / _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \ / // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // / /____/____/ |__/|__/_/|_| /_/ |___/____(_)___/ DD-WRT v3.0 http://www.dd-wrt.com ========================================================== login[1312]: root login on 'console' BusyBox v1.29.3 (2018-10-22 02:08:39 CEST) built-in shell (ash) root@DD-WRT:~# reboot root@DD-WRT:~# send dhcp lease release signal Sending SIGTERM to all processes [ 128.874809] device ath0 left promiscuous mode [ 128.874896] br0: port 2(ath0) entered disabled state [ 128.876632] init (1): drop_caches: 3 unmounting / [ 128.887572] br0: port 3(ath1) entered disabled state Sending SIGKILL to all processes [ 128.922156] init (1): drop_caches: 3 unmounting / [ 129.404405] reboot: Restarting system [ 129.404431] [ 129.404431] Resetting with watch dog! U-Boot 2012.07 [Standard IPQ806X.LN,r40331] (Mar 16 2015 - 16:29:21) CBT U-Boot ver: 1.0.9 smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:0:3:7f:ba:db:2 eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is 00:06:3b:01:41:00 , eth1 Updating boot_count ... done Hit any key to stop autoboot: 0 MMC Device 0 not found MMC Device 0 not found Loading from nand0, offset 0xf80000 Image Name: DD-WRT V3.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2228095 Bytes = 2.1 MiB Load Address: 42208000 Entry Point: 42208000 Automatic boot of image at addr 0x44000000 ... Image Name: DD-WRT V3.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2228095 Bytes = 2.1 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK Loading Kernel Image ... OK OK mtdids not defined, no default present info: "mtdparts" not set Using machid 0x1260 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.135 (bluebat@helios) (gcc version 6.3.0 (LEDE GCC 6.3.0 r4639-eb43a817f7) ) #232 SMP PREEMPT Mon Oct 22 02:10:08 CEST 2018 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt:Machine model: Linksys EA8500 WiFi Router [ 0.000000] OF: fdt:Ignoring memory range 0x41500000 - 0x42000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 13 pages/cpu @ddc06000 s21324 r8192 d23732 u53248 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 478140K/491520K available (5120K kernel code, 281K rwdata, 1060K rodata, 1024K init, 399K bss, 13380K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0800000 (6112 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b464b0 ( 282 kB) [ 0.000000] .bss : 0xc0b48000 - 0xc0babf38 ( 400 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000025] Switching to timer-based delay loop, resolution 160ns [ 0.000207] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000229] pid_max: default: 32768 minimum: 301 [ 0.000323] Security Framework initialized [ 0.000389] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000406] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001004] CPU: Testing write buffer coherency: ok [ 0.001312] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001364] Setting up static identity map for 0x42300000 - 0x42300034 [ 0.176879] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.177087] Brought up 2 CPUs [ 0.177109] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.177119] CPU: All CPU(s) started in SVC mode. [ 0.189859] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.190055] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.190082] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.190168] pinctrl core: initialized pinctrl subsystem [ 0.191512] NET: Registered protocol family 16 [ 0.191862] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.217282] cpuidle: using governor ladder [ 0.248301] cpuidle: using governor menu [ 0.301292] msm_bus_fabric_init_driver [ 0.302242] pps_core: LinuxPPS API ver. 1 registered [ 0.302260] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.302295] PTP clock support registered [ 0.303978] clocksource: Switched to clocksource dg_timer [ 0.308283] NET: Registered protocol family 2 [ 0.309169] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.309212] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.309267] TCP: Hash tables configured (established 4096 bind 4096) [ 0.309319] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.309343] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.309528] NET: Registered protocol family 1 [ 0.320752] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.327828] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.335356] io scheduler noop registered [ 0.335374] io scheduler deadline registered (default) [ 0.337121] 1b500000.pci supply vdda not found, using dummy regulator [ 0.337229] 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.337327] 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.338133] OF: PCI: host bridge /soc/pci@1b500000 ranges: [ 0.338176] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.338203] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.446435] qcom-pcie 1b500000.pci: link up [ 0.446626] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.446649] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.446669] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.446685] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.447200] PCI: bus0: Fast back to back transfers disabled [ 0.449604] PCI: bus1: Fast back to back transfers disabled [ 0.449899] pci 0000:00:00.0: BAR 14: assigned [mem 0x08000000-0x081fffff] [ 0.449926] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.450060] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.450083] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.450979] 1b700000.pci supply vdda not found, using dummy regulator [ 0.451096] 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.451191] 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.451976] OF: PCI: host bridge /soc/pci@1b700000 ranges: [ 0.452014] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.452036] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.562336] qcom-pcie 1b700000.pci: link up [ 0.562508] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.562528] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.562557] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.563016] PCI: bus0: Fast back to back transfers disabled [ 0.565346] PCI: bus1: Fast back to back transfers disabled [ 0.565736] pci 0001:00:00.0: BAR 14: assigned [mem 0x2e000000-0x2e1fffff] [ 0.565763] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.565885] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.565906] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.567286] deviceless supply s1b not found, using dummy regulator [ 0.569332] L2 @ QSB rate. Forcing new rate. [ 0.569501] L2 @ 1200000 KHz [ 0.569648] CPU0 @ 1400000 KHz [ 0.569654] CPU1 @ QSB rate. Forcing new rate. [ 0.569755] CPU1 @ 1400000 KHz [ 0.571088] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.572175] serial8250_init [ 0.572184] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.572823] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.572876] msm_serial 16340000.serial: uartclk = 7372800 [ 0.572913] physical 16340000 = virtual de879000 [ 0.572923] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 168, base_baud = 460800) is a MSM [ 0.572946] msm_serial: console setup on port #0 [ 1.276684] console [ttyMSM0] enabled [ 1.281296] msm_serial: driver initialized [ 1.286057] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1 [ 1.288737] nand: AMD/Spansion S34MS01G2 [ 1.295308] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.299709] 19 ofpart partitions found on MTD device qcom_nand.0 [ 1.306638] Creating 19 MTD partitions on "qcom_nand.0": [ 1.312698] 0x000000000000-0x000000040000 : "SBL1" [ 1.329222] 0x000000040000-0x000000180000 : "MIBIB" [ 1.341553] 0x000000180000-0x0000002c0000 : "SBL2" [ 1.353924] 0x0000002c0000-0x000000540000 : "SBL3" [ 1.354505] random: fast init done [ 1.370765] 0x000000540000-0x000000660000 : "DDRCONFIG" [ 1.382967] 0x000000660000-0x000000780000 : "SSD" [ 1.395399] 0x000000780000-0x000000a00000 : "TZ" [ 1.409363] 0x000000a00000-0x000000c80000 : "RPM" [ 1.423338] 0x000000c80000-0x000000dc0000 : "art" [ 1.435919] 0x000000dc0000-0x000000ec0000 : "APPSBL" [ 1.448174] 0x000000ec0000-0x000000f00000 : "u_env" [ 1.459554] 0x000000f00000-0x000000f40000 : "s_env" [ 1.470911] 0x000000f40000-0x000000f80000 : "devinfo" [ 1.482285] 0x000000f80000-0x000003780000 : "linux" [ 1.539802] 0x000001280000-0x000003780000 : "rootfs" [ 1.593830] mtd: partition "rootfs" set to be root filesystem [ 1.593856] 0x000003780000-0x000005f40000 : "linux2" [ 1.656167] 0x000003a80000-0x000005f40000 : "rootfs2" [ 1.709896] 0x000005f40000-0x000005f80000 : "nvram" [ 1.721258] 0x000005f80000-0x000008000000 : "ddwrt" [ 1.740108] random: crng init done [ 1.770862] libphy: GPIO Bitbanged MDIO: probed [ 1.773369] libphy: Fixed MDIO Bus: probed [ 1.792095] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 2.651406] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.651426] Ring mode enabled [ 2.655515] DMA HW capability register supported[ 2.658376] Enhanced/Alternate descriptors [ 2.664016] Enabled extended descriptors [ 2.667026] RX Checksum Offload Engine supported [ 2.671141] COE Type 2 [ 2.675908] TX Checksum insertion supported [ 2.678085] Wake-Up On Lan supported [ 2.682599] Enable RX Mitigation via HW Watchdog Timer [ 2.687103] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.691195] Ring mode enabled [ 2.696490] DMA HW capability register supported[ 2.699352] Enhanced/Alternate descriptors [ 2.705074] Enabled extended descriptors [ 2.707953] RX Checksum Offload Engine supported [ 2.712121] COE Type 2 [ 2.716884] TX Checksum insertion supported [ 2.719064] Wake-Up On Lan supported [ 2.723578] Enable RX Mitigation via HW Watchdog Timer [ 2.727563] i2c /dev entries driver [ 2.732580] Calibration not found. [ 2.735730] qcom-tsens 900000.thermal-sensor: tsens calibration failed [ 2.739477] CPUidle arm: CPU 0 failed to init idle CPU ops [ 2.745906] GACT probability NOT on [ 2.751101] Mirror/redirect action on [ 2.754572] Simple TC action Loaded [ 2.758640] netem: version 1.3 [ 2.761605] u32 classifier [ 2.764775] Performance counters on [ 2.767414] input device check on [ 2.771148] Actions configured [ 2.775027] Netfilter messages via NETLINK v0.30. [ 2.778411] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 2.783969] nf_conntrack_rtsp v0.7 loading [ 2.789305] xt_time: kernel timezone is -0000 [ 2.793031] ip_set: protocol 6 [ 2.797632] gre: GRE over IPv4 demultiplexor driver [ 2.801405] nf_nat_rtsp v0.7 loading [ 2.805275] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.809139] NET: Registered protocol family 17 [ 2.814395] Bridge firewalling registered [ 2.818545] 8021q: 802.1Q VLAN Support v1.8 [ 2.822706] Registering SWP/SWPB emulation handler [ 2.828050] Key type encrypted registered [ 2.838280] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 2.856273] s1a: Bringing 0uV into 1050000-1050000uV [ 2.856451] s1b: Bringing 0uV into 1050000-1050000uV [ 2.860430] s2a: Bringing 0uV into 800000-800000uV [ 2.865482] s2b: Bringing 0uV into 800000-800000uV [ 2.872469] trying to register driver cpufreq-dt [ 2.875766] searching for nvram [ 2.879404] nvram size = 262144 [ 2.917909] no valid UBI magic found inside mtd13[ 2[ 2.925940] VFS: Mounted root (squashfs filesystem) readonly on device 31:14. [ 2.927087] Freeing unused kernel memory: 1024K start service starting Architecture code for ipq806x cannot open /dev/nvram cannot open /dev/nvram udevtrigger[102]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory sysinit using mac C0:56:27:08:B2:92 mount: mounting ubi0:rootfs_data on /jffs failed: No such device reset boot counter load ATH 802.11 a/b/g Driver insmod: ath_pci.ko: module not found insmod: ath_ahb.ko: module not found load ATH9K 802.11n Driver [ 5.771543] lzma_compress: module license 'unspecified' taints kernel. [ 5.771574] Disabling lock debugging due to kernel taint [ 5.824223] Loading modules backported from Linux version wireless-drivers-next-for-davem-2017-09-01-0-geb464d4a8d09 [ 5.824435] Backport generated by backports.git backports-20160324-111-g97b8d7c4 load ATH/QCA 802.11ac Driver [ 6.354629] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 6.355297] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 6.526949] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2 [ 6.526994] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.538774] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2 [ 6.542713] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.931109] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 6.931145] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 6.941531] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 9.244750] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 9.245004] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 d3e0cdb5 [ 10.467857] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 10.574378] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 10.574970] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 10.746677] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2 [ 10.746718] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.758000] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2 [ 10.762437] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.774530] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 10.779105] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 10.791887] ath10k_pci 0001:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 13.089051] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 13.089310] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 402a8111 [ 14.295363] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 15.410204] dwmac1000: Master AXI performs any burst length [ 15.410244] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 15.414786] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 15.450969] dwmac1000: Master AXI performs any burst length [ 15.451009] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 15.459955] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [USB] checking... umount: can't unmount /mnt: No such file or directory /etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory /etc/preinit: line 45: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_max: nonexistent directory /etc/preinit: line 46: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established: nonexistent directory /etc/preinit: line 47: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout_stream: nonexistent directory cannot open /proc/sys/net/ipv4/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout [ 16.508192] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off /etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory /etc/preinit: line 45: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_max: nonexistent directory /etc/preinit: line 46: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established: nonexistent directory /etc/preinit: line 47: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout_stream: nonexistent directory cannot open /proc/sys/net/ipv4/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_max cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout ath9k deconfigure_single: phy0 ath0 interface wlan0 does not exist! ath9k deconfigure_single: phy1 ath1 interface wlan1 does not exist! [ 17.397697] device br0 entered promiscuous mode killall: ead: no process killed [ 17.456709] br0: port 1(vlan1) entered blocking state [ 17.456739] br0: port 1(vlan1) entered disabled state [ 17.461062] device vlan1 entered promiscuous mode [ 17.465869] device eth0 entered promiscuous mode sh: ead: not found [ 17.479312] br0: port 1(vlan1) entered blocking state [ 17.479341] br0: port 1(vlan1) entered forwarding state [ 17.483913] device br0 left promiscuous mode [ 17.492642] device br0 entered promiscuous mode ifconfig: ioctl 0x8914 failed: Address not available [ 17.505828] device br0 left promiscuous mode ath9k deconfigure_single: phy0 ath0 ath9k deconfigure_single: phy1 ath1 ath9k configure_single: phy0 ath0 sh: write error: Network is down sh: can't create /sys/kernel/debug/ieee80211/phy0/ath9k/chanbw: nonexistent directory call mac80211autochannel for interface: ath0 ath0: freq:2432 qual:96 noise:-99 eirp: 30 ath0: freq:2452 qual:96 noise:-99 eirp: 30 ath0: freq:2412 qual:85 noise:-100 eirp: 30 ath0: freq:2442 qual:73 noise:-99 eirp: 30 ath0: freq:2422 qual:69 noise:-99 eirp: 30 ath0: freq:2462 qual:69 noise:-99 eirp: 30 ath0: freq:2437 qual:48 noise:-99 eirp: 30 ath0: freq:2447 qual:48 noise:-99 eirp: 30 ath0: freq:2417 qual:46 noise:-100 eirp: 30 ath0: freq:2427 qual:45 noise:-99 eirp: 30 ath0: freq:2457 qual:44 noise:-99 eirp: 30 mac80211autochannel interface: ath0 frequency: 2432 setup ath0 C0:56:27:08:B2:94 Configuration file: /tmp/ath0_hostap.conf [ 28.573103] br0: port 2(ath0) entered blocking state [ 28.573127] br0: port 2(ath0) entered disabled state [ 28.577443] device ath0 entered promiscuous mode ath0: interface state UNINITIALIZED->COUNTRY_UPDATE Using interface ath0 with hwaddr c0:56:27:08:b2:94 and ssid "dd-wrt" [ 29.103890] br0: port 2(ath0) entered blocking state [ 29.103915] br0: port 2(ath0) entered forwarding state ath0: interface state COUNTRY_UPDATE->ENABLED ath0: AP-ENABLED ath9k configure_single: phy1 ath1 sh: write error: Network is down sh: can't create /sys/kernel/debug/ieee80211/phy1/ath9k/chanbw: nonexistent directory call mac80211autochannel for interface: ath1 ath1: freq:5745 qual:99 noise:-103 eirp: 30 ath1: freq:5805 qual:99 noise:-103 eirp: 30 ath1: freq:5825 qual:99 noise:-103 eirp: 30 ath1: freq:5765 qual:98 noise:-103 eirp: 30 ath1: freq:5785 qual:98 noise:-103 eirp: 30 ath1: freq:5180 qual:93 noise:-104 eirp: 23 ath1: freq:5200 qual:93 noise:-104 eirp: 23 ath1: freq:5220 qual:93 noise:-104 eirp: 23 ath1: freq:5240 qual:93 noise:-104 eirp: 23 ath1: freq:5260 qual:93 noise:-104 eirp: 23 ath1: freq:5280 qual:93 noise:-104 eirp: 23 ath1: freq:5300 qual:93 noise:-104 eirp: 23 ath1: freq:5320 qual:93 noise:-104 eirp: 23 ath1: freq:5620 qual:93 noise:-104 eirp: 23 ath1: freq:5640 qual:93 noise:-104 eirp: 23 ath1: freq:5500 qual:92 noise:-103 eirp: 23 ath1: freq:5520 qual:92 noise:-103 eirp: 23 ath1: freq:5540 qual:92 noise:-103 eirp: 23 ath1: freq:5560 qual:92 noise:-103 eirp: 23 ath1: freq:5580 qual:92 noise:-103 eirp: 23 ath1: freq:5600 qual:92 noise:-103 eirp: 23 ath1: freq:5680 qual:92 noise:-103 eirp: 23 ath1: freq:5700 qual:92 noise:-103 eirp: 23 ath1: freq:5720 qual:92 noise:-103 eirp: 23 ath1: freq:5660 qual:91 noise:-102 eirp: 23 mac80211autochannel interface: ath1 frequency: 5745 setup ath1 C0:56:27:08:B2:95 Configuration file: /tmp/ath1_hostap.conf [ 39.884643] br0: port 3(ath1) entered blocking state [ 39.884667] br0: port 3(ath1) entered disabled state [ 39.888864] device ath1 entered promiscuous mode ath1: interface state UNINITIALIZED->COUNTRY_UPDATE Using interface ath1 with hwaddr c0:56:27:08:b2:95 and ssid "dd-wrt" [ 40.303362] br0: port 3(ath1) entered blocking state [ 40.303383] br0: port 3(ath1) entered forwarding state ath1: interface state COUNTRY_UPDATE->ENABLED ath1: AP-ENABLED killall: roaming_daemon: no process killed sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max: nonexistent directory cp: can't stat '/tmp/mycron.d/*': No such file or directory [ 40.485463] device vlan2 entered promiscuous mode sh: can't create /sys/devices/platform/i2c-0/0-0048/temp1_max_hyst: nonexistent directory cp: can't stat '/jffs/mycron.d/*': No such file or directory cp: can't stat '/mmc/mycron.d/*': No such file or directory cat: can't open '/proc/net/ip_conntrack_flush': No such file or directory 0 [ 41.231568] device vlan2 left promiscuous mode udhcpc: started, v1.29.3 ath9k radio 1: phy0 ath0 ath9k radio 1: phy1 ath1 cannot open /proc/sys/dev/wifi0/silent cannot open /proc/sys/dev/wifi1/silent udhcpc: sending discover sh: missing ] udhcpc: sending select for 10.72.28.52 /opt/etc/init.d/rcS: No such file or directory /jffs/etc/init.d/rcS: No such file or directory /mmc/etc/init.d/rcS: No such file or directory rmmod: eoip: No such file or directory udhcpc: lease of 10.72.28.52 obtained, lease time 86400 killall: proxywatchdog.sh: no process killed vlan2: No such process /mnt/smbshare umount: can't unmount /mnt/smbshare: No such file or directory rmmod: cifs: No such file or directory rmmod: fscache: No such file or directory killall: schedulerb.sh: no process killed killall: shatd: no process killed killall: wdswatchdog.sh: no process killed The Milkfish Router Services ERROR: Necessary service setting not found: milkfish_username - aborting. cat: can't open '/proc/net/ip_conntrack_flush': No such file or directory 0 cannot open /proc/sys/net/ipv4/conf/br0/loop The Milkfish Router Services Restoring SIP ddsubscriber database from NVRAM... Empty. The Milkfish Router Services Restoring SIP ddaliases database from NVRAM... Empty. cp: can't stat '/tmp/mycron.d/*': No such file or directory cp: can't stat '/jffs/mycron.d/*': No such file or directory cp: can't stat '/mmc/mycron.d/*': No such file or directory process_monitor..done DD-WRT v3.0-r37490M kongat (c) 2018 NewMedia-NET GmbH Release: 10/22/18 DD-WRT login: root Password: ========================================================== ___ ___ _ _____ ______ ____ ___ / _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \ / // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // / /____/____/ |__/|__/_/|_| /_/ |___/____(_)___/ DD-WRT v3.0 http://www.dd-wrt.com ========================================================== login[1460]: root login on 'console' BusyBox v1.29.3 (2018-10-22 02:08:39 CEST) built-in shell (ash) root@DD-WRT:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.135 (bluebat@helios) (gcc version 6.3.0 (LEDE GCC 6.3.0 r4639-eb43a817f7) ) #232 SMP PREEMPT Mon Oct 22 02:10:08 CEST 2018 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt:Machine model: Linksys EA8500 WiFi Router [ 0.000000] OF: fdt:Ignoring memory range 0x41500000 - 0x42000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 122880 [ 0.000000] free_area_init_node: node 0, pgdat c0b457c0, node_mem_map ddc39000 [ 0.000000] Normal zone: 960 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 122880 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 13 pages/cpu @ddc06000 s21324 r8192 d23732 u53248 [ 0.000000] pcpu-alloc: s21324 r8192 d23732 u53248 alloc=13*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs noinitrd console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs root=31:14 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 478140K/491520K available (5120K kernel code, 281K rwdata, 1060K rodata, 1024K init, 399K bss, 13380K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0800000 (6112 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b464b0 ( 282 kB) [ 0.000000] .bss : 0xc0b48000 - 0xc0babf38 ( 400 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000025] Switching to timer-based delay loop, resolution 160ns [ 0.000207] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000229] pid_max: default: 32768 minimum: 301 [ 0.000323] Security Framework initialized [ 0.000389] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000406] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001004] CPU: Testing write buffer coherency: ok [ 0.001312] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001364] Setting up static identity map for 0x42300000 - 0x42300034 [ 0.176879] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.177087] Brought up 2 CPUs [ 0.177109] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.177119] CPU: All CPU(s) started in SVC mode. [ 0.189859] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.190055] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.190082] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.190168] pinctrl core: initialized pinctrl subsystem [ 0.191512] NET: Registered protocol family 16 [ 0.191862] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.217282] cpuidle: using governor ladder [ 0.248301] cpuidle: using governor menu [ 0.301292] msm_bus_fabric_init_driver [ 0.302242] pps_core: LinuxPPS API ver. 1 registered [ 0.302260] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.302295] PTP clock support registered [ 0.303978] clocksource: Switched to clocksource dg_timer [ 0.308283] NET: Registered protocol family 2 [ 0.309169] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.309212] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.309267] TCP: Hash tables configured (established 4096 bind 4096) [ 0.309319] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.309343] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.309528] NET: Registered protocol family 1 [ 0.309582] PCI: CLS 0 bytes, default 64 [ 0.320752] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.327828] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.335356] io scheduler noop registered [ 0.335374] io scheduler deadline registered (default) [ 0.337121] 1b500000.pci supply vdda not found, using dummy regulator [ 0.337229] 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.337327] 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.338133] OF: PCI: host bridge /soc/pci@1b500000 ranges: [ 0.338176] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.338203] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.446435] qcom-pcie 1b500000.pci: link up [ 0.446626] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.446649] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.446669] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.446685] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.446738] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.446895] pci 0000:00:00.0: supports D1 [ 0.446909] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.447200] PCI: bus0: Fast back to back transfers disabled [ 0.447539] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000 [ 0.447789] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.448949] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.449604] PCI: bus1: Fast back to back transfers disabled [ 0.449899] pci 0000:00:00.0: BAR 14: assigned [mem 0x08000000-0x081fffff] [ 0.449926] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.450060] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.450083] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.450514] aer 0000:00:00.0:pcie002: service driver aer loaded [ 0.450979] 1b700000.pci supply vdda not found, using dummy regulator [ 0.451096] 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.451191] 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.451976] OF: PCI: host bridge /soc/pci@1b700000 ranges: [ 0.452014] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.452036] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.562336] qcom-pcie 1b700000.pci: link up [ 0.562508] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.562528] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.562557] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.562604] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.562731] pci 0001:00:00.0: supports D1 [ 0.562741] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 0.563016] PCI: bus0: Fast back to back transfers disabled [ 0.563326] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000 [ 0.563551] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.564731] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 0.565346] PCI: bus1: Fast back to back transfers disabled [ 0.565736] pci 0001:00:00.0: BAR 14: assigned [mem 0x2e000000-0x2e1fffff] [ 0.565763] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.565885] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.565906] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.566280] aer 0001:00:00.0:pcie002: service driver aer loaded [ 0.567286] deviceless supply s1b not found, using dummy regulator [ 0.569332] L2 @ QSB rate. Forcing new rate. [ 0.569501] L2 @ 1200000 KHz [ 0.569648] CPU0 @ 1400000 KHz [ 0.569654] CPU1 @ QSB rate. Forcing new rate. [ 0.569755] CPU1 @ 1400000 KHz [ 0.571088] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.572175] serial8250_init [ 0.572184] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.572823] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.572876] msm_serial 16340000.serial: uartclk = 7372800 [ 0.572913] physical 16340000 = virtual de879000 [ 0.572923] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 168, base_baud = 460800) is a MSM [ 0.572946] msm_serial: console setup on port #0 [ 1.276684] console [ttyMSM0] enabled [ 1.281296] msm_serial: driver initialized [ 1.286057] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1 [ 1.288737] nand: AMD/Spansion S34MS01G2 [ 1.295308] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.299709] 19 ofpart partitions found on MTD device qcom_nand.0 [ 1.306638] Creating 19 MTD partitions on "qcom_nand.0": [ 1.312698] 0x000000000000-0x000000040000 : "SBL1" [ 1.329222] 0x000000040000-0x000000180000 : "MIBIB" [ 1.341553] 0x000000180000-0x0000002c0000 : "SBL2" [ 1.353924] 0x0000002c0000-0x000000540000 : "SBL3" [ 1.354505] random: fast init done [ 1.370765] 0x000000540000-0x000000660000 : "DDRCONFIG" [ 1.382967] 0x000000660000-0x000000780000 : "SSD" [ 1.395399] 0x000000780000-0x000000a00000 : "TZ" [ 1.409363] 0x000000a00000-0x000000c80000 : "RPM" [ 1.423338] 0x000000c80000-0x000000dc0000 : "art" [ 1.435919] 0x000000dc0000-0x000000ec0000 : "APPSBL" [ 1.448174] 0x000000ec0000-0x000000f00000 : "u_env" [ 1.459554] 0x000000f00000-0x000000f40000 : "s_env" [ 1.470911] 0x000000f40000-0x000000f80000 : "devinfo" [ 1.482285] 0x000000f80000-0x000003780000 : "linux" [ 1.539802] 0x000001280000-0x000003780000 : "rootfs" [ 1.593830] mtd: partition "rootfs" set to be root filesystem [ 1.593856] 0x000003780000-0x000005f40000 : "linux2" [ 1.656167] 0x000003a80000-0x000005f40000 : "rootfs2" [ 1.709896] 0x000005f40000-0x000005f80000 : "nvram" [ 1.721258] 0x000005f80000-0x000008000000 : "ddwrt" [ 1.740108] random: crng init done [ 1.770862] libphy: GPIO Bitbanged MDIO: probed [ 1.773369] libphy: Fixed MDIO Bus: probed [ 1.792095] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 2.651406] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.651426] Ring mode enabled [ 2.655515] DMA HW capability register supported [ 2.658376] Enhanced/Alternate descriptors [ 2.664016] Enabled extended descriptors [ 2.667026] RX Checksum Offload Engine supported [ 2.671141] COE Type 2 [ 2.675908] TX Checksum insertion supported [ 2.678085] Wake-Up On Lan supported [ 2.682599] Enable RX Mitigation via HW Watchdog Timer [ 2.687103] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.691195] Ring mode enabled [ 2.696490] DMA HW capability register supported [ 2.699352] Enhanced/Alternate descriptors [ 2.705074] Enabled extended descriptors [ 2.707953] RX Checksum Offload Engine supported [ 2.712121] COE Type 2 [ 2.716884] TX Checksum insertion supported [ 2.719064] Wake-Up On Lan supported [ 2.723578] Enable RX Mitigation via HW Watchdog Timer [ 2.727563] i2c /dev entries driver [ 2.732580] Calibration not found. [ 2.735730] qcom-tsens 900000.thermal-sensor: tsens calibration failed [ 2.739477] CPUidle arm: CPU 0 failed to init idle CPU ops [ 2.745906] GACT probability NOT on [ 2.751101] Mirror/redirect action on [ 2.754572] Simple TC action Loaded [ 2.758640] netem: version 1.3 [ 2.761605] u32 classifier [ 2.764775] Performance counters on [ 2.767414] input device check on [ 2.771148] Actions configured [ 2.775027] Netfilter messages via NETLINK v0.30. [ 2.778411] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 2.783969] nf_conntrack_rtsp v0.7 loading [ 2.789305] xt_time: kernel timezone is -0000 [ 2.793031] ip_set: protocol 6 [ 2.797632] gre: GRE over IPv4 demultiplexor driver [ 2.801405] nf_nat_rtsp v0.7 loading [ 2.805275] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.809139] NET: Registered protocol family 17 [ 2.814395] Bridge firewalling registered [ 2.818545] 8021q: 802.1Q VLAN Support v1.8 [ 2.822706] Registering SWP/SWPB emulation handler [ 2.828050] Key type encrypted registered [ 2.838280] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 2.856273] s1a: Bringing 0uV into 1050000-1050000uV [ 2.856451] s1b: Bringing 0uV into 1050000-1050000uV [ 2.860430] s2a: Bringing 0uV into 800000-800000uV [ 2.865482] s2b: Bringing 0uV into 800000-800000uV [ 2.872469] trying to register driver cpufreq-dt [ 2.875766] searching for nvram [ 2.879404] nvram size = 262144 [ 2.917909] no valid UBI magic found inside mtd13 [ 2.917950] hctosys: unable to open rtc device (rtc0) [ 2.925940] VFS: Mounted root (squashfs filesystem) readonly on device 31:14. [ 2.927087] Freeing unused kernel memory: 1024K [ 5.771543] lzma_compress: module license 'unspecified' taints kernel. [ 5.771574] Disabling lock debugging due to kernel taint [ 5.824223] Loading modules backported from Linux version wireless-drivers-next-for-davem-2017-09-01-0-geb464d4a8d09 [ 5.824435] Backport generated by backports.git backports-20160324-111-g97b8d7c4 [ 6.354629] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 6.355297] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 6.526949] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2 [ 6.526994] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.538774] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2 [ 6.542713] ath10k_pci 0000:01:00.0: Falling back to user helper [ 6.931109] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 6.931145] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 6.941531] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 9.244750] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 9.245004] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 d3e0cdb5 [ 10.467857] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 10.556788] ath: EEPROM regdomain: 0x0 [ 10.556795] ath: EEPROM indicates default country code should be used [ 10.556799] ath: doing EEPROM country->regdmn map search [ 10.556808] ath: country maps to regdmn code: 0x3a [ 10.556815] ath: Country alpha2 being used: US [ 10.556820] ath: Regpair used: 0x3a [ 10.574378] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 10.574970] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 10.746677] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2 [ 10.746718] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.758000] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2 [ 10.762437] ath10k_pci 0001:01:00.0: Falling back to user helper [ 10.774530] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 10.779105] ath10k_pci 0001:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 [ 10.791887] ath10k_pci 0001:01:00.0: firmware ver 10.4-3.5.3-00050 api 5 features no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 5ae23169 [ 13.089051] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin [ 13.089310] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 402a8111 [ 14.295363] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1 [ 14.386753] ath: EEPROM regdomain: 0x0 [ 14.386760] ath: EEPROM indicates default country code should be used [ 14.386766] ath: doing EEPROM country->regdmn map search [ 14.386775] ath: country maps to regdmn code: 0x3a [ 14.386781] ath: Country alpha2 being used: US [ 14.386786] ath: Regpair used: 0x3a [ 15.410204] dwmac1000: Master AXI performs any burst length [ 15.410244] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 15.414786] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 15.450969] dwmac1000: Master AXI performs any burst length [ 15.451009] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 15.459955] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 16.508192] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 17.397697] device br0 entered promiscuous mode [ 17.456709] br0: port 1(vlan1) entered blocking state [ 17.456739] br0: port 1(vlan1) entered disabled state [ 17.461062] device vlan1 entered promiscuous mode [ 17.465869] device eth0 entered promiscuous mode [ 17.479312] br0: port 1(vlan1) entered blocking state [ 17.479341] br0: port 1(vlan1) entered forwarding state [ 17.483913] device br0 left promiscuous mode [ 17.492642] device br0 entered promiscuous mode [ 17.505828] device br0 left promiscuous mode [ 17.566659] ath: EEPROM regdomain: 0x8348 [ 17.566665] ath: EEPROM indicates we should expect a country code [ 17.566671] ath: doing EEPROM country->regdmn map search [ 17.566679] ath: country maps to regdmn code: 0x3a [ 17.566685] ath: Country alpha2 being used: US [ 17.566689] ath: Regpair used: 0x3a [ 17.566696] ath: regdomain 0x8348 dynamically updated by user [ 17.566718] ath: EEPROM regdomain: 0x8348 [ 17.566722] ath: EEPROM indicates we should expect a country code [ 17.566727] ath: doing EEPROM country->regdmn map search [ 17.566732] ath: country maps to regdmn code: 0x3a [ 17.566737] ath: Country alpha2 being used: US [ 17.566742] ath: Regpair used: 0x3a [ 17.566747] ath: regdomain 0x8348 dynamically updated by user [ 28.573103] br0: port 2(ath0) entered blocking state [ 28.573127] br0: port 2(ath0) entered disabled state [ 28.577443] device ath0 entered promiscuous mode [ 29.103890] br0: port 2(ath0) entered blocking state [ 29.103915] br0: port 2(ath0) entered forwarding state [ 39.884643] br0: port 3(ath1) entered blocking state [ 39.884667] br0: port 3(ath1) entered disabled state [ 39.888864] device ath1 entered promiscuous mode [ 40.303362] br0: port 3(ath1) entered blocking state [ 40.303383] br0: port 3(ath1) entered forwarding state [ 40.485463] device vlan2 entered promiscuous mode [ 41.231568] device vlan2 left promiscuous mode root@DD-WRT:~# DD-WRT v3.0-r37490M kongat (c) 2018 NewMedia-NET GmbH Release: 10/22/18 DD-WRT login: